A two-phase generator is connected to two 9012 load resistors. Each coil generates 120 V ac. The value of ...

A two-phase generator is connected to two 90Ω load resistors. Each coil generates 120 V ac. The value of current flowing through the common neutral line will be: A. 1.33 A B. 1.88 A C. 2.66 A D. 1.77 A

by

1 Answer

Answer :

A two-phase generator is connected to two 90Ω load resistors. Each coil generates 120 V ac. The value of current flowing through the common neutral line will be: 1.77 A

by

Related questions

Regarding an AC generator connected to the main electrical bus; as the electric load and power factor vary, a corresponding change is reflected in the generator armature reaction. These changes in armature reaction are compensated for by the __________ A. governor speed droop setting B. voltage regulator C. balance coil D. phase-balance relay

Description : Regarding an AC generator connected to the main electrical bus; as the electric load and power factor vary, a corresponding change is reflected in the generator armature reaction. These changes in ... . governor speed droop setting B. voltage regulator C. balance coil D. phase-balance relay

Last Answer : Answer: B

Two resistors of `6 Omega " and " 9 Omega` are connected in series to a 120 V source. The power consumed by the `6 Omega` resistor is

Description : Two resistors of `6 Omega " and " 9 Omega` are connected in series to a 120 V source. The power consumed by the `6 Omega` resistor is

Last Answer : Two resistors of `6 Omega " and " 9 Omega` are connected in series to a 120 V source. The power consumed by ... 384 W B. 616 W C. 1500 W D. 1800 W

Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor

Description : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

Last Answer : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

Three factors responsible for the change in voltage as load is applied to an AC generator are: 1) the drop in resistance in the armature circuit, 2) the change in flux, and 3) the ____________. A. armature winding speed B. inductance load drop C. coil pitch factor D. armature reactance voltage drop

Description : Three factors responsible for the change in voltage as load is applied to an AC generator are: 1) the drop in resistance in the armature circuit, 2) the change in flux, and 3) the ____________. A. armature winding speed B. inductance load drop C. coil pitch factor D. armature reactance voltage drop

Last Answer : Answer: D

What will be the frequency of a three-phase, six pole, AC generator operating at 1800 revolutions per minute? A. 60 hertz B. 90 hertz C. 120 hertz D. 180 hertz

Description : What will be the frequency of a three-phase, six pole, AC generator operating at 1800 revolutions per minute? A. 60 hertz B. 90 hertz C. 120 hertz D. 180 hertz

Last Answer : Answer: B

The primary coil of a transformer is connected to a 60 V ac source. The secondary coil is connected to a 330

Description : The primary coil of a transformer is connected to a 60 V ac source. The secondary coil is connected to a 330 ohms load. The turns ratio is 3:1. What is the secondary voltage? A.2 V B.20 V C.180 V D.18 V

Last Answer : The primary coil of a transformer is connected to a 60 V ac source. The secondary coil is connected to a 330 ohms load. The turns ratio is 3:1. What is the secondary voltage? A.2 V B.20 V C.180 V D.18 V

The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. separate exciter in a series with the shunt field C. carbon pile regulator in series with the load D. balance coil diverting neutral current through the shunt field

Description : The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. ... in series with the load D. balance coil diverting neutral current through the shunt field

Last Answer : Answer: A

A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured...

Description : A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured across all the resistors except the third resistor. The voltage across the third resistor is: A. 0 V B. 1.2V C. 6V D. 0.6V

Last Answer : A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured across all the resistors except the third resistor. The voltage across the third resistor is: 6V

A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W....

Description : A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ?  (a) 100 VAR (b) 200 VAR (c) 300 VAR (d) 400 VAR

Last Answer : A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ? 400 VAR

The power factor of an AC generator operating singularly is determined by the __________. A. connected load B. prime mover speed C. field excitation D. generator's rated voltage

Description : The power factor of an AC generator operating singularly is determined by the __________. A. connected load B. prime mover speed C. field excitation D. generator's rated voltage

Last Answer : Answer: A

The power factor at which a paralleled AC generator operates is usually adjusted by the _____________. A. connected load B. prime mover speed C. field excitation D. generator's rated voltage

Description : The power factor at which a paralleled AC generator operates is usually adjusted by the _____________. A. connected load B. prime mover speed C. field excitation D. generator's rated voltage

Last Answer : Answer: C

A 100 kVA, 415 V(line), star-connected synchronous machine generates rated open circuit voltage of 415 V

Description : A 100 kVA, 415 V(line), star-connected synchronous machine generates rated open circuit voltage of 415 V at a field current of 15 A. The short circuit armature current at a field current of 10 A is equal to the ... unit saturated synchronous reactance is  (A) 1.731 (B) 1.5 (C) 0.666 (D) 0.577

Last Answer : 0.6

Two 1 kilo ohm, 1/2 W resistors are connected in series. Their combined resistance value and wattage will be

Last Answer : Two 1 kilo-ohm 1/2 W resistors are connected in series. Their combined resistance value and wattage will be 2 kΩ, 1 W.

Which of the following procedures should be used to determine the load of a threephase, delta wound, AC generator? A. Multiply the amperage in one phase by three. B. Divide the total amperage in all phases by three. C. Multiply the amperage in one phase by the square root of three. D. Divide the total amperage in all phases by the square root of three.

Description : Which of the following procedures should be used to determine the load of a threephase, delta wound, AC generator? A. Multiply the amperage in one phase by three. B. Divide the total amperage in all ... square root of three. D. Divide the total amperage in all phases by the square root of three.

Last Answer : Answer: C

Two resistors of resistances `2Omega` and `6Omega` are connected in parallel. This combination is then connected to a battery of emf 2 V and internal

Description : Two resistors of resistances `2Omega` and `6Omega` are connected in parallel. This combination is then connected to a battery of emf 2 V and internal

Last Answer : Two resistors of resistances `2Omega` and `6Omega` are connected in parallel. This combination is then connected to a ... . `(4)/(17)A` D. `1 A`

`6Omega` and `12Omega` resistors are connected in parallel. This combination is connected in series with 10 V battery and `6 Omega` resistor. What is

Description : `6Omega` and `12Omega` resistors are connected in parallel. This combination is connected in series with 10 V battery and `6 Omega` resistor. What is

Last Answer : `6Omega` and `12Omega` resistors are connected in parallel. This combination is connected in series with 10 V battery and ... 4 V B. 16 V C. 2 D. 8 V

There resistors of 3Ω, 10Ω, and 15Ω are connected in parallel to a 30 V...

Description : There resistors of 3Ω, 10Ω, and 15Ω are connected in parallel to a 30 V circuit the current that will flow through the 3Ω resistor is 

Last Answer : There resistors of 3Ω, 10Ω, and 15Ω are connected in parallel to a 30 V circuit the current that will flow through the 3Ω resistor is 10A.

If four 90 ohm resistors are connected in series across an 18 V source, the current equals

Last Answer : If four 90 ohm resistors are connected in series across an 18 V source, the current equals 50 mA.

Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?

Description : Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?

Last Answer : 25 ohms

N resistors of each of resistance R when connected in series offer an equivalent resistance of 50 ohm and when reconnected in parallel the effective resistance is 2 ohm the value of R is

Description : N resistors of each of resistance R when connected in series offer an equivalent resistance of 50 ohm and when reconnected in parallel the effective resistance is 2 ohm the value of R is

Last Answer : 25 ohms

What is the total resistance if 5 resistors of 20 Ω each are connected in series?

Description : What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

Last Answer : What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

What is the equivalent resistance of a network having 5 resistors of each 10ohm connected in parallel?

Description : What is the equivalent resistance of a network having 5 resistors of each 10ohm connected in parallel?  (A) 10 Ohms (B) 50 Ohms (C) 500 Ohms (D) 2 Ohms 

Last Answer : D) 2 ohms Solution: 1/Rt = (1/R)(n) 1/Rt = (1/10) (5) 1/Rt = 5/10    Rt = 2 ohms

1275.42 + 8624.6 – 894.54 – 24.71 = ? a) 8620.27 b) 8738.57 c) 8890.93 d) 8980.77 e) 9012.17

Description : 1275.42 + 8624.6 – 894.54 – 24.71 = ? a) 8620.27 b) 8738.57 c) 8890.93 d) 8980.77 e) 9012.17

Last Answer : d) 8980.77

A three-phase synchronous motor connected to ac mains is running at full load and unity power factor.

Description : A three-phase synchronous motor connected to ac mains is running at full load and unity power factor. lf its shaft load is reduced by half and field current is held constant then its new power factor will be

Last Answer : Leading

A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V,

Description : A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum when the supply frequency is 1 kHz. The ... (A) 40, 400 Hz (B) 10, 100 Hz (C) 20, 50 Hz (D) 50, 20 Hz

Last Answer : A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum ... supply frequency is 1 kHz. The approximate values of Q-factor and bandwidth are, respectively 20, 50 Hz

The power consumed by a coil is 300 W when connected to a 30 V dc source and 108 W when connected to ...

Description : The power consumed by a coil is 300 W when connected to a 30 V dc source and 108 W when connected to a 30 V ac source. The reactance of the coil is

Last Answer : The power consumed by a coil is 300 W when connected to a 30 V dc source and 108 W when connected to a 30 V ac source. The reactance of the coil is 4 Ohm.

In the plane of AC generator coil is parallel to the field, then emf induced in coil is: a. maximum b. minimum c. zero d. intermediate

Description : In the plane of AC generator coil is parallel to the field, then emf induced in coil is: a. maximum b. minimum c. zero d. intermediate

Last Answer : b. minimum

Two light bulbs are connected in series across a 120 V battery. Bulb 1 uses 40 W of power and Bulb 2 uses

Description : Two light bulbs are connected in series across a 120 V battery. Bulb 1 uses 40 W of power and Bulb 2 uses 20 W of power. If bulb 1 alone is connected to the 120 V source, then it will consume (A) 90 W (B) 80 W (C) 60 W (D) 180 W

Last Answer : Two light bulbs are connected in series across a 120 V battery. Bulb 1 uses 40 W of power and Bulb 2 uses 20 W of power. If bulb 1 alone is connected to the 120 V source, then it will consume 90 W

A fuse will 'blow' if _____________. A. an electric motor is stopped suddenly by opening a switch B. the flow of current to the protection device is reversed C. the electrical current exceeds the rated value of the fuse D. unequal resistors are connected in parallel

Description : A fuse will 'blow' if _____________. A. an electric motor is stopped suddenly by opening a switch B. the flow of current to the protection device is reversed C. the electrical current exceeds the rated value of the fuse D. unequal resistors are connected in parallel

Last Answer : Answer: C

When two 100 kΩ resistors are connected in parallel, net resistance is

Description : When two 100 kΩ resistors are connected in parallel, net resistance is

Last Answer : When two 100 kΩ resistors are connected in parallel, net resistance is 50 kΩ

what is equivalent resistance when four 4 Ohm resistors are connected in i) series ii) parallel

Description : what is equivalent resistance when four 4 Ohm resistors are connected in i) series ii) parallel

Last Answer : equivalent resistance

Three identical resistors connected in star consume 5000 W. If the resistors are connected in

Description : Three identical resistors connected in star consume 5000 W. If the resistors are connected in delta across the same supply, the power consumed will be

Last Answer : Three identical resistors connected in star consume 5000 W. If the resistors are connected in delta across the same supply, the power consumed will be 15000 W

Consider a circuit with four resistors in series connected to a voltage source. What happens to the voltage

Description : Consider a circuit with four resistors in series connected to a voltage source. What happens to the voltage across each resistor, if the value of each of the resistors is doubled? A) It will double B) It will remain the same C) It will be halved D) It will become zero

Last Answer : Consider a circuit with four resistors in series connected to a voltage source. What happens to the voltage across each resistor, if the value of each of the resistors is doubled? A) It will double B) It will remain the same C) It will be halved D) It will become zero

When three resistors with unequal values are connected in parallel, _______

Description : When three resistors with unequal values are connected in parallel, _______ A) The current across the resistors is the same  B) The voltage drop across the resistors is the same C) The voltage drops across the resistors is proportional to the resistance of each resistor D) None of these

Last Answer : When three resistors with unequal values are connected in parallel, The voltage drop across the resistors is the same

Consider a circuit with four 10 Ω resistors connected in parallel and the current flowing through the circuit is

Description : Consider a circuit with four 10 Ω resistors connected in parallel and the current flowing through the circuit is 5 A. What will be the current if the above 4 resistors are connected in parallel? A) 5 A B) 50 A C) 500 A D) None of these

Last Answer : Consider a circuit with four 10 Ω resistors connected in parallel and the current flowing through the circuit is 5 A. What will be the current if the above 4 resistors are connected in parallel? A) 5 A B) 50 A C) 500 A D) None of these

Which of the following series combinations of resistors dissipates the most power when connected across a...

Description : Which of the following series combinations of resistors dissipates the most power when connected across a 120 V source? A. One, 220Ω resistor B. Two, 220Ω resistors C. Three, 220Ω resistors D. Four, 220Ω resistors

Last Answer : Which of the following series combinations of resistors dissipates the most power when connected across a 120 V source?  One, 220Ω resistor

Three resistors of 4 Ω, 6 Ω and 9 Ω are connected in parallel. Which resistor consumes the maximum power?

Description : Three resistors of 4 Ω, 6 Ω and 9 Ω are connected in parallel. Which resistor consumes the maximum power?  (A) 4 Ω (B) 6 Ω (C) 9 Ω (D) 17 Ω

Last Answer : (c) 9 ohm

Four identical resistors are first connected in parallel and then in series. ...

Description : Four identical resistors are first connected in parallel and then in series. The resultant resistance of the first combination to the second will be

Last Answer : Four identical resistors are first connected in parallel and then in series. The resultant resistance of the first combination to the second will be  1 / 16 times.

Three equal resistors connected in series across a source of emf together...

Description : Three equal resistors connected in series across a source of emf together dissipate 10 watts of power. What would be the power dissipated in the same resistors when they are connected in parallel across the same source of emf? 

Last Answer : Three equal resistors connected in series across a source of emf together dissipate 10 watts of power. 90 watts would be the power dissipated in the same resistors when they are connected in parallel across the same source of emf.

Three resistors each of 2 ohm are connected together in a triangular shape. The resistance between any two vertices will be

Description : Three resistors each of 2 ohm are connected together in a triangular shape. The resistance between any two vertices will be

Last Answer : Three resistors each of 2 ohm are connected together in a triangular shape. The resistance between any two ... 3//4Omega` C. `3Omega` D. `6Omega`

A 1000 watts heater is connected to a 240 V AC Supply. Then the current drawn by the heater is

Description : A 1000 watts heater is connected to a 240 V AC Supply. Then the current drawn by the heater is

Last Answer : A 1000 watts heater is connected to a 240 V AC Supply. Then the current drawn by the heater is 4.166 amperes

A `5 Omega` resistor is connected in series with a parallel combination of n resistors of `6 Omega` each. The equivalent resistance is `7 Omega`. Find

Description : A `5 Omega` resistor is connected in series with a parallel combination of n resistors of `6 Omega` each. The equivalent resistance is `7 Omega`. Find

Last Answer : A `5 Omega` resistor is connected in series with a parallel combination of n resistors of `6 Omega ... The equivalent resistance is `7 Omega`. Find n.

Three equal resistors connected in series with a source of e m f together dissipate 10 W of power each. What will be the power dissipated if the same resistors are connected in parallel across the same source of e m f? a. 40 W b. 90W c. 100W d. 120W

Description : Three equal resistors connected in series with a source of e m f together dissipate 10 W of power each. What will be the power dissipated if the same resistors are connected in parallel across the same source of e m f? a. 40 W b. 90W c. 100W d. 120W

Last Answer : b. 90W

A 3-phase star-connected 75 MVA, 25 kV 3-phase synchronous generator has a synchronous reactance of...

Description : A 3-phase star-connected 75 MVA, 25 kV 3-phase synchronous generator has a synchronous reactance of 1.0 p.u. The per unit value to a 90 MVA base and 30 kV is (A) 2/15 p.u. (B) 5/6 p.u. (C) 1.0 p.u. (D) 1.2 p.u.

Last Answer : A 3-phase star-connected 75 MVA, 25 kV 3-phase synchronous generator has a synchronous reactance of 1.0 p.u. The per unit value to a 90 MVA base and 30 kV is 5/6 p.u.

In a certain three -wire Y -connected generator, the phase voltages are 2 kV. The magnitudes of the line...

Description : In a certain three -wire Y -connected generator, the phase voltages are 2 kV. The magnitudes of the line voltages will be: A. 2,000 V B. 6,000 V C. 666 V D. 3,464 V

Last Answer : In a certain three -wire Y -connected generator, the phase voltages are 2 kV. The magnitudes of the line voltages will be: 3,464 V

An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes

Description : An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes

Last Answer : Answer: B

What should be kVA rating of each transformer in V-V bank when three phase balanced load is

Description : What should be kVA rating of each transformer in V-V bank when three phase balanced load is 40 kVA ? (A) 19 (B) 28 (C) 37 (D) 23

Last Answer : What should be kVA rating of each transformer in V-V bank when three phase balanced load is 40 kVA ? (A) 19 (B) 28 (C) 37 (D) 23