main function of the current regulator is A. To prevent the reversal flow of current from the battery when dynamo speed is drops. B. To safeguard against flow of high currents to battery when armature develops more current. C. To prevent building up of high voltage in a circuit. D. None of the above

main function of the current regulator is
A. To prevent the reversal flow of current from the battery when dynamo speed is drops. B. To safeguard against flow of high currents to battery when armature develops more current. C. To prevent building up of high voltage in a circuit.
D. None of the above
by

1 Answer

Answer :

B. To safeguard against flow of high currents to battery when armature develops more current.
by

Related questions

Main function of cutout relay in electrical circuit is A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces. B. To restrict the maximum output at high speed. C. To permit the generation to deliver current to the battery or to the lightening and ignition circuit. D. None of the above

Description : Main function of cutout relay in electrical circuit is A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces. B. To restrict the maximum output at ... deliver current to the battery or to the lightening and ignition circuit. D. None of the above

Last Answer : A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces.

A d.c. shunt motor runs at no load speed of 1140 r.p.m. At full load, armature reaction weakens the main flux by 5% whereas the armature circuit voltage drops by 10%. The motor full load speed in r.p.m. is (A) 1080 (B) 1203 (C) 1000 (D) 1200

Description : A d.c. shunt motor runs at no load speed of 1140 r.p.m. At full load, armature reaction weakens the main flux by 5% whereas the armature circuit voltage drops by 10%. The motor full load speed in r.p.m. is (A) 1080 (B) 1203 (C) 1000 (D) 1200

Last Answer : (A) 1080

Alternators are preferred over dynamo because A. Alternators can produce a strong current of 30-40 amperes. B. Alternators don’t required cutout reiny C. Alternators don’t have commutaters D. All of the above

Description : Alternators are preferred over dynamo because A. Alternators can produce a strong current of 30-40 amperes. B. Alternators don’t required cutout reiny C. Alternators don’t have commutaters D. All of the above

Last Answer : D. All of the above

Regarding an AC generator connected to the main electrical bus; as the electric load and power factor vary, a corresponding change is reflected in the generator armature reaction. These changes in armature reaction are compensated for by the __________ A. governor speed droop setting B. voltage regulator C. balance coil D. phase-balance relay

Description : Regarding an AC generator connected to the main electrical bus; as the electric load and power factor vary, a corresponding change is reflected in the generator armature reaction. These changes in ... . governor speed droop setting B. voltage regulator C. balance coil D. phase-balance relay

Last Answer : Answer: B

The total voltage of a series circuit is the _____________. A. sum of the individual voltage drops B. total resistance divided by the total current C. sum of the individual currents multiplied by the number of resistors D. total current divided by the total resistance

Description : The total voltage of a series circuit is the _____________. A. sum of the individual voltage drops B. total resistance divided by the total current C. sum of the individual currents multiplied by the number of resistors D. total current divided by the total resistance

Last Answer : Answer: A

An AC generator operating in parallel loses its excitation without tripping the circuit breaker. This will __________. A. not affect the faulty generator due to the compensation of the other generators B. cause the slip rings to melt C. cause a low voltage differential to develop between the armature and the bus D. cause high currents to be induced in the field windings

Description : An AC generator operating in parallel loses its excitation without tripping the circuit breaker. This will __________. A. not affect the faulty generator due to the compensation of the other generators B. ... between the armature and the bus D. cause high currents to be induced in the field windings

Last Answer : Answer: D

In order to prevent the winch shown in the illustration from turning while troubleshooting the controller circuit, _________________. EL-0102 A. set the dynamic brake by clamping contact 'DB' closed B. set the mechanical brake by the jackscrew provided C. disconnect the brake solenoid at 'B1' and 'B2' D. open the test link preventing current flow to the armature

Description : In order to prevent the winch shown in the illustration from turning while troubleshooting the controller circuit, _________________. EL-0102 A. set the dynamic brake by clamping contact 'DB' closed B. set the ... at 'B1' and 'B2' D. open the test link preventing current flow to the armature

Last Answer : Answer: D

Undervoltage trips are frequently installed on switchboard circuit breakers to trip ____________. A. out generators in the event of severe arcing or sparking B. out generators when there is reversal of power in the main circuit C. the breaker if the generator overspeeds by 5%, but continues to run D. out generators when there is low voltage in the main circuit

Description : Undervoltage trips are frequently installed on switchboard circuit breakers to trip ____________. A. out generators in the event of severe arcing or sparking B. out generators when there is reversal of power ... , but continues to run D. out generators when there is low voltage in the main circuit

Last Answer : Answer: D

The main function of a fuse is to (a) protect the line (b) open the circuit (c) protect the appliance (d) prevent excessive currents (e) none of the above

Description : The main function of a fuse is to (a) protect the line (b) open the circuit (c) protect the appliance (d) prevent excessive currents (e) none of the above

Last Answer : (d) prevent excessive currents

The battery has following three major functions to perform: a) To provide a source of current for engine starting, lighting and use of horn. b) To help control the voltage in the electrical system. c) To store the current produced by dynamo/alternator and to furnish the current d) all of the above. Ans. d

Description : The battery has following three major functions to perform: a) To provide a source of current for engine starting, lighting and use of horn. b) To help control the voltage in the electrical system. c ... the current produced by dynamo/alternator and to furnish the current d) all of the above. Ans. d

Last Answer : ans d

Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal of the sum of the individual currents. C. The total resistance equals the sum of the individual resistances. D. The total voltage equals the sum of the individual voltages across each resistance.

Description : Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal ... resistances. D. The total voltage equals the sum of the individual voltages across each resistance.

Last Answer : Answer: A

The function of the commutator in a DC motor is to ________. A. reverse the flow of current through the armature B. reverse the flow of current in the field poles C. reduce the reluctance of the magnetic path through the motor D. shift the neutral running plane of the brushes to prevent sparking

Description : The function of the commutator in a DC motor is to ________. A. reverse the flow of current through the armature B. reverse the flow of current in the field poles C. reduce the reluctance of the magnetic path through the motor D. shift the neutral running plane of the brushes to prevent sparking

Last Answer : Answer: A

Superchargers are driven by A. Electric current from the battery B. Exhaust gases from engine C. Direct connection with the engine power D. None of the above

Description : Superchargers are driven by A. Electric current from the battery B. Exhaust gases from engine C. Direct connection with the engine power D. None of the above

Last Answer : C. Direct connection with the engine power

Turbo chargers are driven by A. Direct connection with engine power B. Exhaust gases from engine C. Electric current from the battery D. None of the above

Description : Turbo chargers are driven by A. Direct connection with engine power B. Exhaust gases from engine C. Electric current from the battery D. None of the above

Last Answer : B. Exhaust gases from engine

A low-voltage protection circuit is used in electric motor starting equipment to _____________. A. trip circuit contactors when the motor overspeeds due to low voltage B. trip circuit contactors when the motor develops a short circuit due to low voltage C. allow the motor to restart automatically on restoration of voltage without manually resetting D. prevent the motor from restarting automatically on restoration of voltage

Description : A low-voltage protection circuit is used in electric motor starting equipment to _____________. A. trip circuit contactors when the motor overspeeds due to low voltage B. trip circuit ... voltage without manually resetting D. prevent the motor from restarting automatically on restoration of voltage

Last Answer : Answer: D

The purpose of a motor undervoltage protection device is to _____________. A. prevent high armature current when power is restored B. start the motor at a very low voltage C. trip the load off the motor in case of fire D. protect personnel from low voltage shocks

Description : The purpose of a motor undervoltage protection device is to _____________. A. prevent high armature current when power is restored B. start the motor at a very low voltage C. trip the load off the motor in case of fire D. protect personnel from low voltage shocks

Last Answer : Answer: A

Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Description : Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Last Answer : Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Description : iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Last Answer : ∙ Torque is a function of thermal efficiency

When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only and a low resistance meter for DC measurements C. whenever a low impedance meter is not available, regardless of the components being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Description : When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only ... being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Last Answer : Answer: D

A 220 V shunt motor develops a torque of 54 N-m at armature current of 10 A. The torque produced when...

Description : A 220 V shunt motor develops a torque of 54 N-m at armature current of 10 A. The torque produced when the armature current is 20 A, is?

Last Answer : Armature torque, Ta=PØZIa/2πA So Ta1/Ta2=Ia1/Ia2 Ta2=Ta1*Ia2/Ia1        =54*20/10         =108

Brush sparking during commutation may be caused by ________. A. eddy currents in the armature core B. laminations in the generator field pieces C. induced current opposite to coil inductance D. coil inductance discharge occurring at commutation

Description : Brush sparking during commutation may be caused by ________. A. eddy currents in the armature core B. laminations in the generator field pieces C. induced current opposite to coil inductance D. coil inductance discharge occurring at commutation

Last Answer : Answer: D

pecific gravity of fully charged storage battery is ∙ 1.15 ∙ 1.50 ∙ 1.28 ∙ 2.15

Description : pecific gravity of fully charged storage battery is ∙ 1.15 ∙ 1.50 ∙ 1.28 ∙ 2.15

Last Answer : ∙ 1.28

The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. separate exciter in a series with the shunt field C. carbon pile regulator in series with the load D. balance coil diverting neutral current through the shunt field

Description : The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. ... in series with the load D. balance coil diverting neutral current through the shunt field

Last Answer : Answer: A

Three factors responsible for the change in voltage as load is applied to an AC generator are: 1) the drop in resistance in the armature circuit, 2) the change in flux, and 3) the ____________. A. armature winding speed B. inductance load drop C. coil pitch factor D. armature reactance voltage drop

Description : Three factors responsible for the change in voltage as load is applied to an AC generator are: 1) the drop in resistance in the armature circuit, 2) the change in flux, and 3) the ____________. A. armature winding speed B. inductance load drop C. coil pitch factor D. armature reactance voltage drop

Last Answer : Answer: D

Roller chains are used for: a)Higher speed and higher loads b)made of high grade steel c)components are harden and polished d)All of the above

Description : Roller chains are used for: a)Higher speed and higher loads b)made of high grade steel c)components are harden and polished d)All of the above

Last Answer : d)All of the above

High speed diesel A) is used on high speed engine B) has lower fule value then l.s.d per litre. C)both (a) & (b) D)none of the above

Description : High speed diesel A) is used on high speed engine B) has lower fule value then l.s.d per litre. C)both (a) & (b) D)none of the above

Last Answer : C)both (a) & (b)

Piston speed for high speed engine is (a) 300-500 m/min (b) 100-300 m/min (c) 500-700 m/min (d) >700m/min

Description : Piston speed for high speed engine is (a) 300-500 m/min (b) 100-300 m/min (c) 500-700 m/min (d) >700m/min

Last Answer : (a) 300-500 m/min

peed of a high speed engine is (a) <350 rpm (b) 350-1000 rpm (c) >1000rpm (d) none of the above

Description : peed of a high speed engine is (a) 1000rpm (d) none of the above

Last Answer : (c) >1000rpm

V-belt drive transmission system is used when it is designed to achieve a) High speed ratio b) Space requirements are limited c) Both (a) and (b) d) None of the above

Description : V-belt drive transmission system is used when it is designed to achieve a) High speed ratio b) Space requirements are limited c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Description : Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

In the illustration, the component labeled 'EXC' is _______. EL-0003 A. a separate class II regulated DC generator for critical direct current loads B. a generator feeding the FLD winding through the voltage regulator. C. the controller to drive the governor for turbogenerator speed. D. the electronic driver for the switchboard metering circuits

Description : In the illustration, the component labeled 'EXC' is _______. EL-0003 A. a separate class II regulated DC generator for critical direct current loads B. a generator feeding the FLD ... to drive the governor for turbogenerator speed. D. the electronic driver for the switchboard metering circuits

Last Answer : Answer: B

Which of the following statements is true concerning simple parallel resistance circuits? A. The total current flow equals the sum of the individual currents. B. The total current flow equals the reciprocal of the sum of the individual currents. C. The total resistance equals the sum of the individual resistance. D. The total voltage equals the sum of the individual voltages across each resistance.

Description : Which of the following statements is true concerning simple parallel resistance circuits? A. The total current flow equals the sum of the individual currents. B. The total current flow equals the ... resistance. D. The total voltage equals the sum of the individual voltages across each resistance.

Last Answer : Answer: A

What is the function of a fuse wire? (a) To prevent an unduly high electric current from passing through a circuit (b) To increase the current supply (c) To decrease the current supply (d) To stabilise the voltage

Description : What is the function of a fuse wire? (a) To prevent an unduly high electric current from passing through a circuit (b) To increase the current supply (c) To decrease the current supply (d) To stabilise the voltage

Last Answer : Ans:(a)

Which is NOT a characteristic of a series circuit? w) The current is the same throughout. x) The total resistance is the sum of the individual resistance. y) The voltage of the source equals the sum of the circuit's individual voltage drops. z) The total resistance is the sum of the reciprocals of the individual resistances.

Description : Which is NOT a characteristic of a series circuit? w) The current is the same throughout. x) The total resistance is the sum of the individual resistance. y) The voltage of the source ... individual voltage drops. z) The total resistance is the sum of the reciprocals of the individual resistances.

Last Answer : ANSWER: Z -- THE TOTAL RESISTANCE IS THE SUM OF THE RECIPROCALS OF THE RECIPROCAL OF THE INDIVIDUAL RESISTANCES.

Two unpedauces given by Z1 = 10 + j5 and Z2 = 8 + j9 are joined in parallel and connected across a voltage of V = 200 + j0. Calculate the circuit current and branch currents. Draw the vector diagram.

Description : Two unpedauces given by Z1 = 10 + j5 and Z2 = 8 + j9 are joined in parallel and connected across a voltage of V = 200 + j0. Calculate the circuit current and branch currents. Draw the vector diagram.

Last Answer : Solution: Given, Z1=10+j5, Z2=8+j9, V=200+j0

A circuit breaker and a fuse have a basic similarity in that they both _____________. A. can be reset to energize the circuit B. should open the circuit when overloaded C. will burn out when an over current flow develops D. all of the above

Description : A circuit breaker and a fuse have a basic similarity in that they both _____________. A. can be reset to energize the circuit B. should open the circuit when overloaded C. will burn out when an over current flow develops D. all of the above

Last Answer : Answer: B

Flow rates of particular nozzle is directly proportional to a. square root of pressure b. orifice area c. Both (a) and (B) d. none of the above

Description : Flow rates of particular nozzle is directly proportional to a. square root of pressure b. orifice area c. Both (a) and (B) d. none of the above

Last Answer : c. Both (a) and (B)

Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill

Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill

Last Answer : a) Raspbar type cylinder

Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill

Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill

Last Answer : a) Raspbar type cylinder

Most commonly used metering device for bulk flow seed metering of small and medium size seeds (grains) a) Fluted wheel b) Internal double run c) Stationary opening with agitator d) None of the above

Description : Most commonly used metering device for bulk flow seed metering of small and medium size seeds (grains) a) Fluted wheel b) Internal double run c) Stationary opening with agitator d) None of the above

Last Answer : a) Fluted wheel

Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder

Description : Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder

Last Answer : (b) Spike tooth cylinder

If a three-phase induction motor is operated under a light load and it develops an open in one of its supply lines, the motor will _____________. A. continue to run, but will vibrate and have reduced torque B. speed up due to the reduced number of poles C. run cooler due to reduced current flow D. stop

Description : If a three-phase induction motor is operated under a light load and it develops an open in one of its supply lines, the motor will _____________. A. continue to run, but will vibrate and have reduced ... speed up due to the reduced number of poles C. run cooler due to reduced current flow D. stop

Last Answer : Answer: A

In an AC dynamo, the speed at which the coil rotates is doubled. How would this affect a) the frequency of output voltage b) the maximum output voltage?

Description : In an AC dynamo, the speed at which the coil rotates is doubled. How would this affect a) the frequency of output voltage b) the maximum output voltage?

Last Answer : a) Frequency is doubled b) Maximum output voltage is doubled.

Multiple universal joint are preferred over single joint because they : A. provide higher strength B. minimize speed fluctuation C. are lighter in weight D. are more flexible

Description : Multiple universal joint are preferred over single joint because they : A. provide higher strength B. minimize speed fluctuation C. are lighter in weight D. are more flexible

Last Answer : B. minimize speed fluctuation

Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more

Description : Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more

Last Answer : a) Higher cylinder speed.

raft increases with increase in forward speed for most of the implement, mainly due to a) More rapid acceleration of any soil particles that is moved appreciably b) More working width c) Increased working depth d) Draft decreases with increase in speed of implement

Description : raft increases with increase in forward speed for most of the implement, mainly due to a) More rapid acceleration of any soil particles that is moved appreciably b) More working width c) Increased working depth d) Draft decreases with increase in speed of implement

Last Answer : a) More rapid acceleration of any soil particles that is moved appreciably

The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance between the speed pick up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

Description : The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance ... up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

One of the main advantages of disc brakes over drum brakes is that the disc brake : U. Can stop a vehicle in a shorter distance V. Is more heat resistant W. Weighs less than drum brakes X. Requires less pedal force to stop the vehicle

Description : One of the main advantages of disc brakes over drum brakes is that the disc brake : U. Can stop a vehicle in a shorter distance V. Is more heat resistant W. Weighs less than drum brakes X. Requires less pedal force to stop the vehicle

Last Answer : . Requires less pedal force to stop the vehicle