How many amps run through a high tension power line?

How many amps run through a high tension power line?
by

1 Answer

Answer :

Watts/Volts = Amps. So a typical 400 kV (400,000 V) might have a current draw of 100 MW (100,000,000 W). This would equal 250 Amps.
by

Related questions

I need a new 12 volt AC adapter; do amps matter?

Description : I need a new 12 volt AC adapter; do amps matter?

Last Answer : answer:Amperage does matter. if you do not use the proper amperage for a certain device, it will either fry again or not work at all. i had this problem with an extended volume control on a ... they also have the best selection of AC adapters i have ever seen. they were very helpful at RS.

How many volts does it take to power an Arduino?

Description : How many volts does it take to power an Arduino?

Last Answer : 5volts is enough to supply the Arduino.

Can I plug a 6V adapter into a USB-hub?

Description : Can I plug a 6V adapter into a USB-hub?

Last Answer : Try it for 15 mins, feel it, and if it scalds your hand like you just touched the sun, then its probably not a good idea to keep using this.

how can we express 0.40 kV in volts?

Description : how can we express 0.40 kV in volts?

Last Answer : Kvx1000=400v

A current of 5 amps passes through a 10 ohm resistor. What power is dissipated by this resistor under these conditions?

Description : A current of 5 amps passes through a 10 ohm resistor. What power is dissipated by this resistor under these conditions?

Last Answer : ANSWER: 250 WATTS

Presence of high concentration of ozone and smog in atmospheric air causes the(A) Embrittlement & decrease of folding resistance of paper(B) Cracking of rubber products(C) Fading of dye on textiles(D) Damage of electrical insulator on high tension power line

Description : Presence of high concentration of ozone and smog in atmospheric air causes the (A) Embrittlement & decrease of folding resistance of paper (B) Cracking of rubber products (C) Fading of dye on textiles (D) Damage of electrical insulator on high tension power line

Last Answer : (B) Cracking of rubber products

What is a high tension power line?

Description : What is a high tension power line?

Last Answer : High tension power line is a high voltage of 115 kv and power line is underground transimissio used by urbun areas

What is the maximum current allowed to be drawn from the secondary of a 2 KVA step-down transformer with a turns ratio of four to one if connected across a 440 volt line? A. 1.1 amps B. 4.5 amps C. 18.1 amps D. 22.7 amps

Description : What is the maximum current allowed to be drawn from the secondary of a 2 KVA step-down transformer with a turns ratio of four to one if connected across a 440 volt line? A. 1.1 amps B. 4.5 amps C. 18.1 amps D. 22.7 amps

Last Answer : Answer: C

What is the maximum allowable primary current of a 2 KVA step-down transformer with a four to one turns ratio if connected across a 440 volt line? A. 1.1 amps B. 4.5 amps C. 18.1 amps D. 27.7 amps

Description : What is the maximum allowable primary current of a 2 KVA step-down transformer with a four to one turns ratio if connected across a 440 volt line? A. 1.1 amps B. 4.5 amps C. 18.1 amps D. 27.7 amps

Last Answer : Answer: B

In the schematic diagram of the DC compound generator shown in the illustration, the positive ammeter reading is 500 amps and the negative ammeter reading is 475 amps. What is the current flow through the neutral bus? EL-0037 A. 0 amp B. 12.5 amp C. 25 amp D. 975 amp

Description : In the schematic diagram of the DC compound generator shown in the illustration, the positive ammeter reading is 500 amps and the negative ammeter reading is 475 amps. What is the current flow through the neutral bus? EL-0037 A. 0 amp B. 12.5 amp C. 25 amp D. 975 amp

Last Answer : Answer: C

A load is connected to the secondary of the transformer illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps

Description : A load is connected to the secondary of the transformer illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps

Last Answer : Answer: C

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 24 kohms, and R2 is 3610 ohms what is the current flowing through R1? EL-0036 A. .434 milliamps B. .005 amp C. 6.00 amps D. 2.4 milliamps

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 24 kohms, and R2 is 3610 ohms what is the current flowing through R1? EL-0036 A. .434 milliamps B. .005 amp C. 6.00 amps D. 2.4 milliamps

Last Answer : Answer: A

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the current flowing through R1? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the current flowing through R1? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Last Answer : Answer: A

What is the current flowing through R3 of the illustrated circuit if the battery is 12 VDC and resistance of R1 is 2 ohms, R2 is 3 ohms, and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Description : What is the current flowing through R3 of the illustrated circuit if the battery is 12 VDC and resistance of R1 is 2 ohms, R2 is 3 ohms, and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Last Answer : Answer: A

What is the current flowing through R2 of the illustrated circuit if the voltage is 12 VDC and the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Description : What is the current flowing through R2 of the illustrated circuit if the voltage is 12 VDC and the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Last Answer : Answer: B

What is the current through R2 of the circuit illustrated if the resistances of R1 is 2 ohms, R2 is 4 ohms, and R3 is 4 ohms with a 6 volt battery? EL-0021 A. 0.5 amp B. 1.5 amps C. 3.0 amps D. 6 amps

Description : What is the current through R2 of the circuit illustrated if the resistances of R1 is 2 ohms, R2 is 4 ohms, and R3 is 4 ohms with a 6 volt battery? EL-0021 A. 0.5 amp B. 1.5 amps C. 3.0 amps D. 6 amps

Last Answer : Answer: B

What is the current flow through R1 of the circuit illustrated if the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms with a 12 VDC battery? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Description : What is the current flow through R1 of the circuit illustrated if the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms with a 12 VDC battery? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Last Answer : Answer: C

What is the current flowing through R1 of the illustrated circuit with a 6 VDC battery if the resistance of R1 is 2 ohms, R2 is 4 ohms and R3 is 4 ohms? EL-0021 A. 0.5 amps B. 1.5 amps C. 3.0 amps D. 6 amps

Description : What is the current flowing through R1 of the illustrated circuit with a 6 VDC battery if the resistance of R1 is 2 ohms, R2 is 4 ohms and R3 is 4 ohms? EL-0021 A. 0.5 amps B. 1.5 amps C. 3.0 amps D. 6 amps

Last Answer : Answer: C

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the current flowing through R2? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the current flowing through R2? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Last Answer : Answer: A

A load is connected to the secondary of the device illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps

Description : A load is connected to the secondary of the device illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps

Last Answer : Answer: C

A current of 5 amps passes through a 10 ohm resistor. How many joules of energy will be generated by this resistor in 2 seconds?

Description : A current of 5 amps passes through a 10 ohm resistor. How many joules of energy will be generated by this resistor in 2 seconds? 

Last Answer : ANSWER: 500 JOULES

An electric heating element supplied with 120 volts draws 15 amps. How much power will be consumed? A. 15 watts B. 45.57 watts C. 180 watts D. 1800 watts

Description : An electric heating element supplied with 120 volts draws 15 amps. How much power will be consumed? A. 15 watts B. 45.57 watts C. 180 watts D. 1800 watts

Last Answer : Answer: D

A three-phase alternator is operating at 450 volts, 250 amps at 0.6 power factor. If the power factor increases to 0.8, the kw load potential will increase by _____________. A. 38.525 kw B. 116.91 kw C. 155.88 kw D. 194.85 kw

Description : A three-phase alternator is operating at 450 volts, 250 amps at 0.6 power factor. If the power factor increases to 0.8, the kw load potential will increase by _____________. A. 38.525 kw B. 116.91 kw C. 155.88 kw D. 194.85 kw

Last Answer : Answer: A

A three-phase alternator is developing 300 amps, with a 0.8 power factor, at 450 volts. The true indicated power on the kilowatt meter, located on the main switchboard, will be ____________. A. 133 kw B. 155 kw C. 187 kw D. 212 kw

Description : A three-phase alternator is developing 300 amps, with a 0.8 power factor, at 450 volts. The true indicated power on the kilowatt meter, located on the main switchboard, will be ____________. A. 133 kw B. 155 kw C. 187 kw D. 212 kw

Last Answer : Answer: C

A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter would then read ____________. A. 181.4 KW B. 186.8 KW C. 194.2 KW D. 201.4 KW

Description : A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter would then read ____________. A. 181.4 KW B. 186.8 KW C. 194.2 KW D. 201.4 KW

Last Answer : Answer: B

Electrical power is expressed in _____________. A. ohms B. volts C. amps D. watts

Description : Electrical power is expressed in _____________. A. ohms B. volts C. amps D. watts

Last Answer : Answer: D

A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter reading would increase by ___ A. 17.8 KW B. 23.2 KW C. 30.6 KW D. 37.8 KW

Description : A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter reading would increase by ___ A. 17.8 KW B. 23.2 KW C. 30.6 KW D. 37.8 KW

Last Answer : Answer: B

A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.

In practical op-amps, what is the effect of high frequency on its performance?

Description : In practical op-amps, what is the effect of high frequency on its performance?

Last Answer : The open-loop gain of op-amp decreases at higher frequencies due to the presence of parasitic capacitance. The closed-loop gain increases at higher frequencies and leads to instability.

Surface tension (A) Acts in the plane of the interface normal to any line in the surface (B) Is also known as capillarity (C) Is a function of the curvature of the interface (D) Decreases with fall in temperature

Description : Surface tension (A) Acts in the plane of the interface normal to any line in the surface (B) Is also known as capillarity (C) Is a function of the curvature of the interface (D) Decreases with fall in temperature

Last Answer : Answer: Option A

The force per unit length across such a line in the surface is called _________.  a. force per length  b. surface tension  c. Pressure  d. Density

Description : The force per unit length across such a line in the surface is called _________.  a. force per length  b. surface tension  c. Pressure  d. Density

Last Answer : surface tension

Is it the amp's in that kill you, and not the voltage?

Description : Is it the amp's in that kill you, and not the voltage?

Last Answer : The voltage is the pressure that drives the amps through a wire. Resistance (load) is the control. Amperage is the flow of electrons. There is no resistance when a bolt of lightning hits you (so the amperage is out of this world) and the voltage is through the roof.

How many amps will I need?

Description : How many amps will I need?

Last Answer : It should tell you what it needs for power in the specs, no way to know otherwise, but if it’s a walk in I’d guess a 30 amp circuit at least.

What do you like about your Orange amp compared to amps you've owned in the past?

Description : What do you like about your Orange amp compared to amps you've owned in the past?

Last Answer : answer:I don't own an Orange have Fender gear but I did get to play through the Thunderverb 50 with a 4 12 bottom and it had a killer sound the rivaled Marshall half stacks I have played ... Effects that has pretty much replaced all the old Boss pedals I have. Nothing will replace my Cry Baby!

What are some good touring acoustic guitar amps?

Description : What are some good touring acoustic guitar amps?

Last Answer : Roland Cube

How many amps it takes to kill someone,?

Description : How many amps it takes to kill someone,?

Last Answer : It's not a cut and dry matter of a certain number of amps = death, but let's see. Well the Wikipedia article on electric shock seems to have info on this. It claims, Generally, currents approaching 100 mA ... to humans ranges from 0.06 A to 0.07 A, depending on the person and the type of current.

Where is the noise coming from when I hook several amps together and how do I fix it?

Description : Where is the noise coming from when I hook several amps together and how do I fix it?

Last Answer : Feedback. They are too close to each other. Experiment with different configurations separated in various ways.

What are the major differences between car amps?

Description : What are the major differences between car amps?

Last Answer : answer:I'm pretty sure that channels just represent speakers. So 2 channels, means you can hook up 2 speakers. 4 channels, 4 speakers & so on. As for classes.. if it's an ... D technique from Tripath. Class T modulates the pulses based on the individual characteristics of the output transistors.

Is AMPS the number of coulombs per second or 1.6x10^-19 per seconds?

Description : Is AMPS the number of coulombs per second or 1.6x10^-19 per seconds?

Last Answer : not sure, but according to wikipedia: http://en.wikipedia.org/wiki/Ampere a current of one ampere is one coulomb of charge going past a given point per second or more specifically Since ... to 6.24150948 1018 elementary charges, such as electrons, moving past a boundary in one second.

Making a solar USB charger, question about amps?

Description : Making a solar USB charger, question about amps?

Last Answer : This will really depend on the solar panels output at any given time and what you are trying to charge. A cell phone will generally never exceed 1 Amp. The wires that the power will be transmitted on can do over an amp, so I would not be worried about that.

How many amps does it take to kill a person?

Description : How many amps does it take to kill a person?

Last Answer : F’real?

What is Digital AMPS (D-AMPS) ?

Description : What is Digital AMPS (D-AMPS) ?

Last Answer : Digital AMPS (D-AMPS) is a second generation ( 2G ) cellular technology that refers to another development in the first generation system of North America called AMPS (Advanced Mobile Phone Service). ... has been retired and has been replaced by GSM / GPRS and CDMA 2000 cellular technology.

What is the amps for 400 volts and 5800 watts phase?

Description : What is the amps for 400 volts and 5800 watts phase?

Last Answer : Need answer

What is the resistance of a circuit that operates on 12 volts and draws 7 amps?

Description : What is the resistance of a circuit that operates on 12 volts and draws 7 amps?

Last Answer : Need answer

How many amps will a 230 vac 3500 watts heater draw?

Description : How many amps will a 230 vac 3500 watts heater draw?

Last Answer : Since power = voltage * currentwe have current=power/voltage so 3500 watts/230 volts = about15.218 amperes in a heater using a resistance to generate heat.This should be valid even though the "230 vac" indicates that it isan AC circuit and not a DC circuit.

How many amps will a computer draw?

Description : How many amps will a computer draw?

Last Answer : Depends on the computer. Laptop, desktop, mainframe? Just thecomputer or computer and monitor?

How many amps in 6 watts at 12 volts?

Description : How many amps in 6 watts at 12 volts?

Last Answer : Wattage is volts times amps. To find amps when you know voltsand watts, divide wattage by voltage. In this case, it would be 0.5amps.

How many amps does a 1500 watt heater need?

Description : How many amps does a 1500 watt heater need?

Last Answer : Feel Free to Answer

How many amps needed for induction range?

Description : How many amps needed for induction range?

Last Answer : Feel Free to Answer