An OP amp has a slew rate of 1V/µs. At a signal frequency of 0.1 MHz, the maximum undistorted sine wave ...

An OP amp has a slew rate of 1V/µs. At a signal frequency of 0.1 MHz, the maximum undistorted sine wave amplitude is (a) 8V (b) 4.82 V (c) 2.02 V (d) 1.592 V
by

1 Answer

Answer :

Slew rate = 2πfv

where v is the amplitude

V=(1/2π*0.1) = 1.592V
by

Related questions

When the initial slope of input sine wave is greater than the slew rate of an OPAMP, the output:

Description : When the initial slope of input sine wave is greater than the slew rate of an OPAMP, the output: (1) Has no offset (2) Approaches to triangular waveshape (3) Is pure sinusoidal (4) Is square wave 

Last Answer : When the initial slope of input sine wave is greater than the slew rate of an OPAMP, the output: Approaches to triangular waveshape

A sine wave of 15 kHz is changing at a faster rate than a sine wave with a frequency of?

Description : A sine wave of 15 kHz is changing at a faster rate than a sine wave with a frequency of? B.12 kHz C.18 kHz D.1.3 MHz

Last Answer : A sine wave of 15 kHz is changing at a faster rate than a sine wave with a frequency of? B.12 kHz C.18 kHz D.1.3 MHz

A sine wave has a frequency of 50 Hz. Its angular frequency is _______ radian/second.

Last Answer :  A sine wave has a frequency of 50 Hz. Its angular frequency is 100 n radian/second.

In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the

Description : In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the (A) applied load (B) internal compensation (C) impedance of the source (D) power dissipation in the chip

Last Answer : In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the internal compensation

A 4 GHz carrier is amplitude modulated by a low-pass signal of maximum cut off frequency 1 MHz

Description : A 4 GHz carrier is amplitude modulated by a low-pass signal of maximum cut off frequency 1 MHz. lf this signal is to be ideally sampled, the minimum sampling frequency should be nearly

Last Answer : A 4 GHz carrier is amplitude modulated by a low-pass signal of maximum cut off frequency 1 MHz. lf this signal is to be ideally sampled, the minimum sampling frequency should be nearly 4 Ghz

An OP amp has an open loop gain of 1,00,000. If the feedback fraction is 0.02, the approximate closed loop...

Description : An OP amp has an open loop gain of 1,00,000. If the feedback fraction is 0.02, the approximate closed loop gain is (a) 1 (b) 1,00,000 (c) 50 (d) 0.02

Last Answer : The closed loop gain Ag = G/(1+G*f) Where G is the open loop gain and f is the feedback fraction  So Ag = 49.975

The purpose of a 'slew rate controller' in a circuit such as shown in the illustration is to ______________. EL-0096 A. limit the rate of change of a signal B. introduce a 'live zero' factor into the circuit C. shape the linear input into a non-linear output D. reduce air pressure to a value required by a combination circuit

Description : The purpose of a 'slew rate controller' in a circuit such as shown in the illustration is to ______________. EL-0096 A. limit the rate of change of a signal B. introduce a 'live zero' ... linear input into a non-linear output D. reduce air pressure to a value required by a combination circuit

Last Answer : Answer: A

A 100 pF capacitor has a maximum charging current of 150 μA.What is the slew rate ?

Description : A 100 pF capacitor has a maximum charging current of 150 μA.What is the slew rate ? (A) 1.5 V/μs (B) 1.05 V/μs (C) 0.15mV/s (D) 10.5 mV/s

Last Answer : A 100 pF capacitor has a maximum charging current of 150 μA.What is the slew rate ? (A) 1.5 V/μs (B) 1.05 V/μs (C) 0.15mV/s (D) 10.5 mV/s

In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?

Description : In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?

Last Answer : 0 volts.

Op-amp can provide maximum output current of A. 25 mA B. 30 mA C. 35 mA D. 40 mA

Description : Op-amp can provide maximum output current of A. 25 mAB. 30 mA C. 35 mA D. 40 mA

Last Answer :  25 mA

Define the following terms related to Op-Amp: i) CMRR ii) SVRR

Description : Define the following terms related to Op-Amp: i) CMRR ii) SVRR

Last Answer : Definition:- i) SVRR: It is defined as the ratio of change of input offset voltage to the change in one supply voltage while keeping other supply voltage constant. Ideally,SVRR=0  ii)CMMR:-The ... gain should exceed common-mode gain, this will be a positive number, and the higher the better.

State any two characteristics of an ideal Op-amp.

Description : State any two characteristics of an ideal Op-amp.

Last Answer : Characteristics of Op-amp: i) Input offset voltage ii) Input offset current iii) Input bias current iv) Differential input resistance v) Input capacitance vi) CMRR-common mode rejection ration vii) ... voltage rejection ratio(SVRR) viii) Output resistance ix) Voltage gain x) Bandwidth xi) Slew rate

Draw and explain the Op-amp based subtractor

Description : Draw and explain the Op-amp based subtractor

Last Answer : Working The subtractor circuit is a basic op-amp circuit whose output voltage is the difference between two input voltages.  In the above circuit, the two input voltages are V1 and V2.  The op amp is used ... When differential gain is 1, ie Rf = R,  the output voltage is Vo = (V2 - V1).

Draw the diagram of zero crossing detector using op-amp and explain its working.

Description : Draw the diagram of zero crossing detector using op-amp and explain its working.

Last Answer : The zero crossing detector circuit is an important application of the op-amp comparator circuit. It can also be called as the sine to square wave converter. Anyone of the inverting or non-inverting ... the possibility of any false zero crossing due to noise voltages at the op-amp input.

What is the Output voltage of Op-amp for input voltage of Vi1=150 μV,Vi2=140 μV if the amplifier ...

Description : What is the Output voltage of Op-amp for input voltage of Vi1=150 μV,Vi2=140 μV if the amplifier has differential gain of Ad=4000 and value of CMRR is 100. 

Last Answer : i don know

A _________ sine wave is not useful in data communications; we need to send a _______signal. A) composite; single-frequency B) single-frequency; composite C) single-frequency;double-frequency D) none of the above

Description : A _________ sine wave is not useful in data communications; we need to send a _______signal. A) composite; single-frequency B) single-frequency; composite C) single-frequency;double-frequency D) none of the above

Last Answer : single-frequency; composite

A sine wave in the ______domain can be representedby onesingle spikein the _____domain. A) time; frequency B) frequency; time C) time; phase D) phase; time

Description : A sine wave in the ______domain can be representedby onesingle spikein the _____domain. A) time; frequency B) frequency; time C) time; phase D) phase; time

Last Answer : time; frequency

What determines the frequency of a sine wave?

Description : What determines the frequency of a sine wave?

Last Answer : The rate at which the vector which is generating the sine wave is rotating.

(i) Draw the time domain and frequency domain representation of sine wave and triangular wave. (ii) Define frequency and wavelength.

Description : (i) Draw the time domain and frequency domain representation of sine wave and triangular wave. (ii) Define frequency and wavelength.

Last Answer : (i)Time domain and frequency domain representation of sine wave time domain and frequency domain representation of triangular wave.   ii) Define frequency and wavelength. Frequency ... : Wavelength can be defined as the distance between two successive crests troughs of a wave. 

When a sine wave has a frequency of 100 Hz in 12 s it goes through?

Description : When a sine wave has a frequency of 100 Hz in 12 s it goes through? A.1/100 cycle B.12 cycles C.120 cycles D.1,200 cycles

Last Answer : When a sine wave has a frequency of 100 Hz in 12 s it goes through? A.1/100 cycle B.12 cycles C.120 cycles D.1,200 cycles

The RMS value of a sine-wave current may also be expressed as the _____________. A. average value B. maximum value C. effective value D. instantaneous value

Description : The RMS value of a sine-wave current may also be expressed as the _____________. A. average value B. maximum value C. effective value D. instantaneous value

Last Answer : Answer: C

If the maximum amplitude of a sine wave is 2 V, the minimum amplitude is________ V. A) 2 B) 1 C) -2 D) between -2 and 2

Description : If the maximum amplitude of a sine wave is 2 V, the minimum amplitude is________ V. A) 2 B) 1 C) -2 D) between -2 and 2

Last Answer : -2

An eight stage ripple counter uses a flip-flop with propagation delay of 75 nanoseconds. The pulse width of the strobe is 50ns. The frequency of the input signal which can be used for proper operation of the counter is approximately (A) 1 MHz. (B) 500 MHz. (C) 2 MHz. (D) 4 MHz.

Description : An eight stage ripple counter uses a flip-flop with propagation delay of 75 nanoseconds. The pulse width of the strobe is 50ns. The frequency of the input signal which can be used for proper operation of the counter is approximately (A) 1 MHz. (B) 500 MHz. (C) 2 MHz. (D) 4 MHz.

Last Answer : Maximum time taken for all flip-flops to stabilize is 75ns x 8 + 50 = 650ns. Frequency of operation must be less than 1/650ns = 1.5 MHz.

______ is the time duration for one horizontal trace. A. 48µs B. 52 µs C. 62 µs D. 50 µs

Description : ______ is the time duration for one horizontal trace. A. 48µs B. 52 µs C. 62 µs D. 50 µs

Last Answer : B. 52 µs

Tropospheric scatter is a method of sky wave propagation for which of the following frequency bands? A. 300 kHz to 3 MHz B. 3 MHz to 30 MHz C. 30 MHz to 300 MHz D. 300 MHz to 3 GHz

Description : Tropospheric scatter is a method of sky wave propagation for which of the following frequency bands? A. 300 kHz to 3 MHz B. 3 MHz to 30 MHz C. 30 MHz to 300 MHz D. 300 MHz to 3 GHz

Last Answer : D. 300 MHz to 3 GHz

Which of the following frequency bands is best suited for sky wave propagation? A. 30 to 300 kHz B. 3 MHz to 30 MHz C. 30 MHz to 300 MHz D. 3 GHz to 30 GHz

Description : Which of the following frequency bands is best suited for sky wave propagation? A. 30 to 300 kHz B. 3 MHz to 30 MHz C. 30 MHz to 300 MHz D. 3 GHz to 30 GHz

Last Answer : B. 3 MHz to 30 MHz

Which of the following frequency bands is best suited for ground wave propagation? A. 30 to 300 kHz B. 300 kHz to 3 MHzC. 3 MHz to 30 MHz D. 30 MHz to 300 MHz

Description : Which of the following frequency bands is best suited for ground wave propagation? A. 30 to 300 kHz B. 300 kHz to 3 MHz C. 3 MHz to 30 MHz D. 30 MHz to 300 MHz

Last Answer : A. 30 to 300 kHz

What is the frequency of a 2-cm sound wave in sea water at 25˚C? A. 76 kHz B. 76 Hz C. 76 MHz D. 76 mHz

Description : What is the frequency of a 2-cm sound wave in sea water at 25˚C? A. 76 kHz B. 76 Hz C. 76 MHz D. 76 mHz

Last Answer : A. 76 kHz

Define each of following terms of operational amplifiers i) Slew rate ii) Input offset voltage iii) Voltage gain iv) Input capacitance

Description : Define each of following terms of operational amplifiers i) Slew rate ii) Input offset voltage iii) Voltage gain iv) Input capacitance

Last Answer : i) Slew rate:- Maximum rate of change of o/p voltage per unit of time. It is express in volt/µsec.  ii) Input offset voltage:- The voltage that must be applied between two ... capacitance that can be measured at either be inverting or non-inverting terminal with other terminal connected to ground.

Instantaneous value of a sine wave voltage

Description : Instantaneous value of a sine wave voltage

Last Answer : Instantaneous value of a sine wave voltage

Draw a labeled block diagram of sine wave generator and state function of each block.

Description : Draw a labeled block diagram of sine wave generator and state function of each block. 

Last Answer : Function Generator:  This instrument can deliver sine, triangular & square waves with frequency range of 0.01 Hz to 100 kHz.  The frequency control network is governed by a frequency ... voltage reaches a predetermined level on the negative slope of the integrator's output voltage.

The phase difference between sine and cosine function for a given wave form is

Description : The phase difference between sine and cosine function for a given wave form is

Last Answer : The phase difference between sine and cosine function for a given wave form is 900

When sine wave is given as input to Schmitt trigger then it generates :

Description : When sine wave is given as input to Schmitt trigger then it generates : (A) Sine wave (B) Saw tooth wave (C) Triangle wave (D) Square wave

Last Answer : When sine wave is given as input to Schmitt trigger than it generates Square Wave

One sine wave has a positive - going zero crossing at 15° and another sine wave has a positive - going zero...

Description : One sine wave has a positive - going zero crossing at 15° and another sine wave has a positive - going zero crossing at 55°. The angle between the two waveforms is -  a) 0° b) 45° c) 40° d) None of the above

Last Answer : One sine wave has a positive - going zero crossing at 15° and another sine wave has a positive - going zero crossing at 55°. The angle between the two waveforms is - 40° 

The equation of 50 Hz current sine wave having r.m.s. value of 60 A is?

Description : The equation of 50 Hz current sine wave having r.m.s. value of 60 A is?

Last Answer : (60*√2)Sin(2π*50*t)

Form factor for a sine wave is?

Description : Form factor for a sine wave is?

Last Answer : 1.11

For a sine wave with peak value Imax the r.m.s. value is?

Description : For a sine wave with peak value Imax the r.m.s. value is?

Last Answer : For a sine wave with peak value Imax the r.m.s. value is 0.707.

what is mean by sine wave?

Description : what is mean by sine wave?

Last Answer : Hi, Sine wave means it is the wave form of sinusoidal wave generally of voltage or current. It takes the path of positive & negative half cycles. 1 set of positive and negative half cycles is called 1 cycle. frequency is no. of cycles per second (HZ). Thanks K.Srikanth

What is Op -Amp ?

Description : What is Op -Amp ?

Last Answer : The operational amplifier is abbreviated as OP-Amp . This OP-Amp is a high gain direct coupled negative feedback amplifier circuit with multiple transistors. Op-Amp is a modular , multistage amplifying device with a ... of op-amp is 500 ml. Op-amp IC : A709, LM108, LM208, CA741 and CA741T.

What is op amp?

Description : What is op amp?

Last Answer : An operational amplifier, which is often called an op-amp, is a DC-coupled high-gain electronic voltage amplifier with a differential input and, usually, a single-ended output.[1] An op-amp ... at the input terminals (ideally infinite) and low output impedance at the output terminal(s) (idea

What is op amp?

Description : What is op amp?

Last Answer : An operational amplifier, which is often called an op-amp, is a DC-coupled high-gain electronic voltage amplifier with a differential input and, usually, a single-ended output.[1] An op-amp ... at the input terminals (ideally infinite) and low output impedance at the output terminal(s) (idea

What is the type of feedback used in an op-amp Schmitt trigger?

Description : What is the type of feedback used in an op-amp Schmitt trigger?

Last Answer : The type of feedback used in an op-amp Schmitt trigger is positive feedback.

What is the basic building block of an op-amp?

Description : What is the basic building block of an op-amp?

Last Answer : The basic building block of an op-amp is differential amplifier.

What is the type of feedback employed in the inverting op-amp amplifier?

Description : What is the type of feedback employed in the inverting op-amp amplifier?

Last Answer : Negative feedback is employed in the inverting op-amp amplifier.

What are the DC characteristics of an op-amp?

Description : What are the DC characteristics of an op-amp?

Last Answer : a. input bias current b. Input offset current c .Input offset voltage d. Thermal drift

What are the AC characteristics of an op-amp?

Description : What are the AC characteristics of an op-amp?

Last Answer : a. Frequency response b. Slew rate

What is compensated op-amp?

Description : What is compensated op-amp?

Last Answer : Op-amp, which uses a capacitor internally for compensation, is called a compensated op-amp. This op-amp has a high gain stability and low bandwidth.

What is an op-amp?

Description : What is an op-amp?

Last Answer : The operational amplifier is a multi-terminal device, which is quite complex internally. An operational amplifier is a direct coupled high gain amplifier usually consisting of one or more ... as well as ac input signals and was originally designed for computing such mathematical functions.