Description : Strain energy in a spring should be (a) Large (b) Small (c) Zero (d) None
Last Answer : (a) Large
Description : Deflection in a spring should be (a) Large (b) Small (c) Zero (d) None
Description : Most important features of any spring are (a) Deflection, stiffness and strength (b) Stiffness, bending and shear strengths (c) Strain energy, deflection and strength (d) None
Last Answer : (c) Strain energy, deflection and strength
Description : The strain energy stored in a spiral spring is given by? (a) 12M²L/Ebtᵌ (b) 6M²L/Ebtᵌ (c) 8M²L/Ebtᵌ (d) None of the listed
Last Answer : (b) 6M²L/Ebtᵌ
Description : In spring balances, the spring is used (a) To apply forces (b) To absorb shocks (c) To store strain energy (d) To measure forces
Last Answer : (d) To measure forces
Description : Strain energy in a leaf spring is (a) W x δ (b) W x δ/3 (c) W x δ/2 (d) None
Last Answer : (c) W x δ/2
Description : Resilience of spring is (a) Strain energy per unit length (b) Strain energy per unit area (c) Strain energy per unit mass (d) None
Last Answer : (d) None
Description : Strain energy in a close coiled helical spring is (a) τ2/8G (b) τ2/16G (c) τ2/4G (d) None
Last Answer : (c) τ2/4G
Description : Deflection in a spring should be (a) Large (b) Medium (c) Small (d) None
Description : Initial gap between two turns of a close coil helical tension spring should be a. 0.5 mm b. based on the maximum deflection c. 1 mm d. zero
Last Answer : d. zero
Description : The springs in brakes and clutches are used (a) To apply forces (b) To measure forces (c) To absorb shocks (d) To absorb strain energy
Last Answer : (a) To apply forces
Description : In the strain energy method of slope and deflection ,load is applied a. gradually b.suddenly c.with an impact. d.None.
Last Answer : c.with an impact.
Description : The strain energy will be higher in which shaft under the same torque (a) Solid shaft (b) Hollow shaft (c) Same in Solid as well as hollow shaft (d) None
Last Answer : (b) Hollow shaft
Description : The axial deflection of spring for the small angle of θ is given by? a) 328PDᵌN/Gd⁴ b) 8PDᵌN/Gd⁴ c) 16PDᵌN/Gd⁴ d) 8PD²N/Gdᵌ
Last Answer : b) 8PDᵌN/Gd⁴
Description : Lame’s equation used to find the thickness of the cylinder is based on maximum strain failure. a) True b) False
Last Answer : b) False
Description : The maximum strain in a thick cylinder under pi will be a) σh/E+μ σl/E b) σh/ E+ μσr/E c) σr/E+μ σl/E d) None
Last Answer : b) σh/ E+ μσr/E
Description : Longitudinal strain in a thin shell is a) σh /E b) σl /E c) σr /E d) None
Last Answer : d) None
Description : Hoop strain in a thin shell is a) σh /E b) σl /E c) 3 σh /E d) None
Description : In a simple bending theory, one of the assumption is that the plane sections before bending remain plane after bending. This assumption means that a. stress is uniform throughout the beam b. ... the distance from the neutral axis d. strain is proportional to the distance from the neutral axis
Last Answer : d. strain is proportional to the distance from the neutral axis
Description : When a beam is subjected to a bending moment the strain in a layer is …………the distance from the neutral axis. (a) Independent of (b) Directly proportional to (c) Inversely proportional to (d) None of these
Last Answer : (b) Directly proportional to
Description : Variation of bending strain in a beam has (a) Parabolic variation (b) Linear variation (c) Cubical variation (d) None
Last Answer : (b) Linear variation
Description : The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram
Last Answer : (d) Trust diagram
Description : Which stress strain curve is more steep (a) For a ductile material (b) For a brittle material (c) For a pure metal (d) None
Last Answer : b) For a brittle material
Description : Linear stress strain curve is for a (a) Load ∞ displacement (b) Load ∞ ( 1/displacement) (c) Load = ( displacement)2 (d) None
Last Answer : (a) Load ∞ displacement
Description : 70. Shear strain is a (a) Linear strain (b) Parabolic strain (c) Angular strain (d) None
Last Answer : (c) Angular strain
Description : Shear strain is a (a) Linear strain (b) Parabolic strain (c) Logarithmic strain (d) None
Description : In a composite body, consisting of two different materials...........will be same in both materials. (a) Stress (b) Strain (c) Both stress and strain (d) None of these
Last Answer : (b) Strain
Description : When a wire is stretched to double in length, the longitudinal strain produced in it is (a) 0.5 (b) 1.0 (c) 1.5 (d) 2.0
Last Answer : b) 1.0
Description : The statement : stress is proportional to strain, i.e. the Hooke’s law holds good upto (a) Elastic Limit (b) Proportional Limit (c) Plastic Limit (d) Yield point
Last Answer : (b) Proportional Limit
Description : Which of the following is a dimensionless quantity? (a) Shear stress (b) Poison’s ratio (c) Strain (d) Both (b) and (c)
Last Answer : (d) Both (b) and (c)
Description : The ratio of lateral strain to linear strain is called (a) Modulus of Elasticity (b) Modulus of Rigidity (c) Bulk Modulus (d) Poisson’s Ratio
Last Answer : (d) Poisson’s Ratio
Description : The deformation per unit length is called (a) Strain (b) Stress (c) Elasticity (d) None of these
Last Answer : (a) Strain
Description : Poisson’s ratio is a. Lateral strain / Longitudinal strain b. Shear strain / Lateral strain c. Longitudinal strain / Lateral strain d. Lateral strain / Volumetric strain
Last Answer : a. Lateral strain / Longitudinal strain
Description : Bulk modulus of elasticity is a. Tensile stress / Tensile strain b. Shear stress / Shear strain c. Tensile stress / Shear strain d. Normal stress on each face of cube / Volumetric strain
Last Answer : d. Normal stress on each face of cube / Volumetric strain
Description : Modulus of rigidity is (a)Tensile stress / Tensile strain (a)Shear stress / Shear strain (a)Tensile stress / Shear strain (a)Shear stress / Tensile strain
Last Answer : (a)Shear stress / Shear strain
Description : Young’s Modulus of elasticity is (a)Tensile stress / Tensile strain (b)Shear stress / Shear strain (c)Tensile stress / Shear strain (d)Shear stress / Tensile strain
Last Answer : a)Tensile stress / Tensile strain
Description : Which of the following is not a basic type of strain? (a)Compressive strain (b)Shear strain (c)Area strain (d)Volume strain
Last Answer : (c)Area strain
Description : In a watch, the spring is used to store energy. The energy is released (a) To stop the watch (b) To run the watch (c) To change the time (d) All of these (
Last Answer : (b) To run the watch
Description : If a close-coiled helical spring absorbs 50 N-mm of energy while extending by 5 mm, its stiffness will be (a) 2 N/mm (b) 4 N/mm (c) 6 N/mm (d) 10 N/mm
Last Answer : (d) 10 N/mm
Description : In a watch, the spring is used to store energy. The energy is released (a) To stop the watch (b) To run the watch (c) To change the time (d) All of these
Description : In case of a laminated spring, the load at which the plates become straight is called (a) working load (b) safe load (c) proof load (d) none
Last Answer : (c) proof load
Description : The type of spring used to achieve any linear and non-linear load-deflection characteristics is (a)spiral spring (b) non-ferrous spring (c)Belleville spring (d) torsion spring
Last Answer : (c)Belleville spring
Description : The type of spring used to achieve greater load carrying capacity within given space is (a)spiral spring (b) springs in series (c)multi-leaf spring (d) concentric spring
Last Answer : (d) concentric spring
Description : With a leaf spring type of suspension, interference between steering and suspension system can be (a) front end of the spring is pin joined and the rear end is shackled (b) front end of the spring is ... joined (c) both end of the spring are shackled (d) both end of the spring are pin joined
Last Answer : (b) front end of the spring is shackled and the rear end is pin joined
Description : The clips placed at intervals along some leaf spring to prevent spring leaf separation on rebound are (a) rebound clips (b) separation clips (c) interval clips (d)relief clips
Last Answer : (a) rebound clips
Description : The laminated spring which is in common use, is of the type (a) full elliptic (b) semi elliptic (c)one quarter elliptic (d)three quarter elliptic
Last Answer : (b) semi elliptic