Description : Deflection in a spring should be (a) Large (b) Small (c) Zero (d) None
Last Answer : (a) Large
Description : Deflection in a spring should be (a) Large (b) Medium (c) Small (d) None
Description : Initial gap between two turns of a close coil helical tension spring should be a. 0.5 mm b. based on the maximum deflection c. 1 mm d. zero
Last Answer : d. zero
Description : Strain energy in a spring should be (a) Large (b) Small (c) Zero (d) None
Description : The axial deflection of spring for the small angle of θ is given by? a) 328PDᵌN/Gd⁴ b) 8PDᵌN/Gd⁴ c) 16PDᵌN/Gd⁴ d) 8PD²N/Gdᵌ
Last Answer : b) 8PDᵌN/Gd⁴
Description : The type of spring used to achieve any linear and non-linear load-deflection characteristics is (a)spiral spring (b) non-ferrous spring (c)Belleville spring (d) torsion spring
Last Answer : (c)Belleville spring
Description : The weight or pressure required to deflect a spring in mm is called the spring (a) Weight (b) deflection (c) rate (d) rebound
Last Answer : c) rate
Description : Most important features of any spring are (a) Deflection, stiffness and strength (b) Stiffness, bending and shear strengths (c) Strain energy, deflection and strength (d) None
Last Answer : (c) Strain energy, deflection and strength
Description : Belleville spring can only produce linear load deflection characteristics. (a) Only linear (b) Linear as well as non linear (c) Non-linear (d) None of the mentioned
Last Answer : (b) Linear as well as non linear
Description : The most important property for the spring material is (a) High elastic limit (b) High deflection value (c) Resistance to fatigue and shock (d) All of these
Last Answer : (d) All of these
Description : The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity
Last Answer : b) Spring stiffness
Description : Maximum deflection in a leaf spring is given by (a) 3WL3/4Enbt3 (b) 3WL3/8Enbt3 (c) 3WL3/16Enbt3 (d) None
Last Answer : (b) 3WL3/8Enbt3
Description : A spring is designed for (a) Higher strength (b) Higher deflection (c) Higher stiffness (d) None
Last Answer : (b) Higher deflection
Description : Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4
Last Answer : a) 7
Description : Deflection in a close coiled helical spring is (a) 16 WR3n/Gd4 (b) 32 WR3n/Gd4 (c) 64 WR3n/Gd4 (d) None
Last Answer : (c) 64 WR3n/Gd4
Description : The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4
Last Answer : (a)1/2
Last Answer : (b) Spring stiffness
Description : Which of the following statements is/are true for a simply supported beam? a. Deflection at supports in a simply supported beam is maximum. b.Deflection is maximum at a point where slope is zero . c. Slope is minimum at supports in a simply supported beam. d. All of the above
Last Answer : b.Deflection is maximum at a point where slope is zero .
Description : In cantilever beam the slope and deflection at the free end is ---------. a.zero b.maximum c.minimum d.none of above.
Last Answer : b.maximum
Description : When two Belleville springs are in parallel, half force is obtained for a given deflection. (a) Half force (b) Double force (c) Same force (d) Can’t be determined
Last Answer : (b) Double force
Description : When two Belleville sprigs are arranged in series, half deflection is obtained for same force. (a) One fourth deflection (b) Double deflection (c) Four time deflection (d) None of the listed
Last Answer : (b) Double deflection
Description : eaf springs are designed on the basis of (a) Maximum bending stresses (b) Maximum deflection (c) Maximum bending as well as maximum deflection (d) None
Last Answer : (c) Maximum bending as well as maximum deflection
Description : In continuous beam, the intermediate beams are subjected to a. some bending moment b. no bending moment c. no slope d.no deflection
Last Answer : a. some bending moment
Description : In continuous over the mid span, the deflection is a. concave up b. concave down c. convex up d. convex down
Last Answer : a. concave up
Description : Sinking of support effects the a. deflection at supports b. moments at supports c. fixity d. deformation at supports
Last Answer : b. moments at supports
Description : In continuous beam between intermediate supports the deflection is a. convex down b. convex up c. concave up d. concave down
Last Answer : b. convex up
Description : Which of the following theorem can be used for deflection in fixed beams a. Mohr’s first theorem b. Mohr’s second theorem c. Mohr’s third theorem d.Mohr’s fourth theorem
Last Answer : b. Mohr’s second theorem
Description : For the same span and loads fixed beam in comparison with simply supported beams has a. lesser value of maximum deflection b. more value of maximum deflecction c.twice the value of maximum deflecction d.same value of maximum deflecction
Last Answer : a. lesser value of maximum deflection
Description : Deflection of an off centre loaded fixed beam is a.Wa3 b3/ 3L3EI b.Wa3b3/ 8L3EI c.Wa3b3/ 192L3EI d.Wa3b3/ 384L3EI
Last Answer : a.Wa3 b3/ 3L3EI
Description : For a fixed beam with UDL, maximum deflection is a.wL4/48EI b.wL4/192EI c. wL4/384EI d.wL3/192EI
Last Answer : c. wL4/384EI
Description : For a fixed beam with midpoint load point deflection for x
Last Answer : c. (Px2/48EI)(3L-4x)
Description : For a fixed beam with midpoint load point, maximum deflection at the centre is a.PL3/ 192EI b.PL2/ 48EI c.PL4/ 192EI d.PL3/ 48EI
Last Answer : a.PL3/ 192EI
Description : A beam 3m long simply supported at its ends ,is carrying a point load W at the centre.If the slope at the ends of the beam should not exceed 10,find the deflection at the centre of beam? a.18.41 mm b.13.45 mm c.17.45 mm d.21.67 mm.
Last Answer : c.17.45 mm
Description : A cantilever of length 3 m carries a uniformly distributed load over the entire length.If the deflection at the free end is 40 mm,find the slope at the free end. a.0.0115 rad b.0.01777 rad c.0.001566 rad d.0.00144 rad
Last Answer : b.0.01777 rad
Description : A cantilever of length 3 m carries two point loads of 2 KN at the free end and 4KN at a distance of 1m from the free end .What is the deflection at the free end? Take E= 2×105 N/mm2and I= 108 mm4. a.2.56 mm b.3.84 mm c.1.84 mm d.5.26mm
Last Answer : c.1.84 mm
Description : A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.
Last Answer : d.16.27 mm.
Description : A cantilever of length 3m carries a point load of 60 KN at a distance of 2m from the fixed end.If E= 2×105 and I=108, what is the deflection at the free end?. a.7 mm b.14 mm c.26 mm d.52 mm.
Last Answer : b.14 mm
Description : The slope at the free end of a cantilever of length 1m is 10 .If the cantilever carries a uniformly distributed load over the whole length ,then the deflection at the free end will be a.1cm b.1.309 cm c.2.618 cm. d.3.927cm.
Last Answer : b.1.309 cm
Description : A simply supported beam carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the distributed load per unit length is doubled and also depth of beam is doubled ,then the deflection at the centre would be a.2y b.4y c.y/2 d.y/4.
Last Answer : d.y/4.
Description : A simply supported beam is of rectangular section.It carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the depth of beam is doubled ,the deflection at the centre would be a.2y b.4y c.y/2 d.y/8.
Last Answer : d.y/8.
Description : A beam is designed on the basis of a. Maximum deflection. b.Minimum deflection c.Maximum slope d.None.
Last Answer : a. Maximum deflection.
Description : Deflection due to shear force as compared to bending moment will be a.equal b.less c.More d.None.
Last Answer : b.less
Description : Deflection is found out by moment area method by using a. First moment of area. b. Second moment of area. c. Third moment of area. d.None.
Last Answer : a. First moment of area.
Description : In the strain energy method of slope and deflection ,load is applied a. gradually b.suddenly c.with an impact. d.None.
Last Answer : c.with an impact.
Description : Which bracket is used in Macaulays method of slope and deflection. a.Parenthesis() b.Square brackets [] c.braces {} d.None.
Last Answer : b.Square brackets []
Description : Deflection underthe load in a S.S beam with W not at the centre will be a.4Wa2b2/ 3EI l . b.2Wa2b2/3EIl. c.Wa2 b2/ 3EIL. d.None.
Last Answer : c.Wa2 b2/ 3EIL.
Description : Maximum deflection in a cantilever beam with UDL w over the entire length will be a. At the free end. b. At the fixed end. c. At the centre d. None.
Last Answer : a. At the free end.