A concentric spring consists of 2 sprigs of diameter 10mm and 4mm. The net force acting on the composite spring is 5000N. Find the force acting on each of the two springs. (a) 1232.2N and 3767.8N (b) 786.4N and 4213.6N (c) 689.7N and 4310.3N (d) 645.3N and 4354.7N

A concentric spring consists of 2 sprigs of diameter 10mm and 4mm. The net force  acting on the composite spring is 5000N. Find the force acting on each of the two springs. (a) 1232.2N and 3767.8N (b) 786.4N and 4213.6N (c) 689.7N and 4310.3N (d) 645.3N and 4354.7N
by

1 Answer

Answer :

(c) 689.7N and 4310.3N
by

Related questions

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Last Answer : c) 41666.7N

A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the leaves are 100mm and 12mm respectively. Calculate the initial pre load required to close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can’t be determined

Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can't be determined

Last Answer : (b) 4674.1N

Find the shear stress in the spring wire used to design a helical compression sprig if a load of 1200N is applied on the spring. Spring index is 6, and wire diameter 7mm. a) 452.2N/mm² b) 468.6N/mm² c) 512.2N/mm² d) None of the listed

Description : Find the shear stress in the spring wire used to design a helical compression sprig if a load of 1200N is applied on the spring. Spring index is 6, and wire diameter 7mm. a) 452.2N/mm² b) 468.6N/mm² c) 512.2N/mm² d) None of the listed

Last Answer : b) 468.6N/mm²

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

Overlap in a leaf spring is (a) L/n (b) L/2n (c) L/3n (d) None

Description : Overlap in a leaf spring is (a) L/n (b) L/2n (c) L/3n (d) None

Last Answer : (b) L/2n

Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed

Description : Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed

Last Answer : b) 1102.8N

A railway wagon moving with a speed of 1.5m/s is brought to rest by bumper consisting of two springs. Mass of wagon is 100kg. The springs are compressed by 125mm. Calculate the maximum force acting on each spring. a) 1200N b) 1500N c) 1800N d) 2000N

Description : A railway wagon moving with a speed of 1.5m/s is brought to rest by bumper consisting of two springs. Mass of wagon is 100kg. The springs are compressed by 125mm. Calculate the maximum force acting on each spring. a) 1200N b) 1500N c) 1800N d) 2000N

Last Answer : c) 1800N

11.Theploidy of the zygote in angiosperms after double fertilization is (a) 4n (b) n (c) 2n (d) 8n.

Description : 11.Theploidy of the zygote in angiosperms after double fertilization is (a) 4n (b) n (c) 2n (d) 8n.

Last Answer : (c) 2n

Light is normally incident on a thin soap film and is reflected. If the wavelength of this light is "L" and the index of refraction of the soap film is "N", complete destructive interference will occur for a film thickness of: w) L / 8N x) L / 4N y) L / 2N z) 3L / 4N

Description : Light is normally incident on a thin soap film and is reflected. If the wavelength of this light is "L" and the index of refraction of the soap film is "N", complete destructive interference will occur for a film thickness of: w) L / 8N x) L / 4N y) L / 2N z) 3L / 4N

Last Answer : ANSWER: Y -- L / 2N 

The type of spring used to achieve greater load carrying capacity within given space is (a)spiral spring (b) springs in series (c)multi-leaf spring (d) concentric spring

Description : The type of spring used to achieve greater load carrying capacity within given space is (a)spiral spring (b) springs in series (c)multi-leaf spring (d) concentric spring

Last Answer : (d) concentric spring

Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Description : Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Last Answer : a) 7

When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring (B) Wire diameter of each spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Description : When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring ... spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Last Answer : (D) Square of wire diameter of each spring

Two concentric springs with stiffness equal to 100 N/mm and 80 N/mm respectively, when subjected to load of 900N will deflect by a. 9mm b. 11.25 mm c. 5mm d. 31.5 mm

Description : Two concentric springs with stiffness equal to 100 N/mm and 80 N/mm respectively, when subjected to load of 900N will deflect by a. 9mm b. 11.25 mm c. 5mm d. 31.5 mm

Last Answer : c. 5mm

A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Last Answer : c) 8mm

The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4

Description : The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4

Last Answer : (a)1/2

The stiffness of the close coil helical spring is (A) d 4N/8D 3n (B) d 4N/4D 3n (C) 4D 3N/d 4n (D) 8D 3N/d 4n

Description : The stiffness of the close coil helical spring is  (A) d 4N/8D 3n (B) d 4N/4D 3n (C) 4D 3N/d 4n (D) 8D 3N/d 4n

Last Answer : (A) d 4N/8D 3n

When two Belleville sprigs are arranged in series, half deflection is obtained for same force. (a) One fourth deflection (b) Double deflection (c) Four time deflection (d) None of the listed

Description : When two Belleville sprigs are arranged in series, half deflection is obtained for same force. (a) One fourth deflection (b) Double deflection (c) Four time deflection (d) None of the listed

Last Answer : (b) Double deflection

A close coil helical spring of mean diameter D consists of n coils of diameter d. If it carries an axial load W, the energy stored in the spring, is (A) 4WD²n/d 4N (B) 4W²Dn/d 4N (C) 4W²D3n/d 4N (D) 4W²D3n²/d 4N

Description : A close coil helical spring of mean diameter D consists of n coils of diameter d. If it carries an axial  load W, the energy stored in the spring, is  (A) 4WD²n/d 4N (B) 4W²Dn/d 4N (C) 4W²D3n/d 4N (D) 4W²D3n²/d 4N

Last Answer : (C) 4W²D3n/d 4N

When two helical springs of equal lengths are arranged to form a cluster spring, then a. Shear stress in each spring will be equal b. Load taken by each spring will be half the total load c. Only A is correct d. Both A and B is correct

Description : When two helical springs of equal lengths are arranged to form a cluster spring, then a. Shear stress in each spring will be equal b. Load taken by each spring will be half the total load c. Only A is correct d. Both A and B is correct

Last Answer : d. Both A and B is correct

For keeping the stress wholly compressive the load may be applied on a circular column anywherewithin a concentric circle of diameter (a) d/2 (b) d/3 (c) d/4 (d) d/8

Description : For keeping the stress wholly compressive the load may be applied on a circular column anywherewithin a concentric circle of diameter (a) d/2 (b) d/3 (c) d/4 (d) d/8

Last Answer : (c) d/4

A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the leaves are 100mm and 12mm respectively. If modulus of elasticity is 207000N/mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm

Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... /mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm

Last Answer : b) 24.9mm

find the value of n in the equation 6.2n – 3.7n = 85 + 45. -General Knowledge

Description : find the value of n in the equation 6.2n – 3.7n = 85 + 45. -General Knowledge

Last Answer : 6.2n - 3.7n = 85 + 45; 2.5n = 130; n = 130/2.5; n = 52

A close-coiled helical spring of stiffness 30 N/mm is arranged in series with another such spring of stiffness 60 N/mm. The stiffness of composite unit is (a) 20 N/mm (b) 30 N/mm (c) 45 N/mm (d) 90 N/mm

Description : A close-coiled helical spring of stiffness 30 N/mm is arranged in series with another such spring of stiffness 60 N/mm. The stiffness of composite unit is (a) 20 N/mm (b) 30 N/mm (c) 45 N/mm (d) 90 N/mm

Last Answer : (a) 20 N/mm

Two close-coiled helical springs are equal in all respects except the number of turns. If the number of turns are in the ratio of 2:3, then the stiffness of the spring will be in the ratio of (a) 2:3 (b) 4:9 (c) 3:2 (d) 9:4

Description : Two close-coiled helical springs are equal in all respects except the number of turns. If the number of turns are in the ratio of 2:3, then the stiffness of the spring will be in the ratio of (a) 2:3 (b) 4:9 (c) 3:2 (d) 9:4

Last Answer : (c) 3:2

A close –coiled helical spring is cut into two equal parts. The stiffness of the resulting springs will be (a) same (b) double (c) half (d) One-fourth

Description : A close –coiled helical spring is cut into two equal parts. The stiffness of the resulting springs will be (a) same (b) double (c) half (d) One-fourth

Last Answer : (b) double

Solve : `(2n + 3)/(6n -5) = 1`

Description : Solve : `(2n + 3)/(6n -5) = 1`

Last Answer : Solve : `(2n + 3)/(6n -5) = 1`

If a body weighs 12N on the surface of the earth, how much will it weigh on the surface of the moon where acceleration due to gravity is only one-sixth of that on earth's surface? (1) 12N (2) 2N (3) 10N (4) 6N

Description : If a body weighs 12N on the surface of the earth, how much will it weigh on the surface of the moon where acceleration due to gravity is only one-sixth of that on earth's surface? (1) 12N (2) 2N (3) 10N (4) 6N

Last Answer : (2) 2N Explanation: Weight is mass x g. Since mass is constant and g is only 16thof that on the earth. The weight on the moon is only 16th of that on the earth.

A concentric spring consist of two helical compression springs (A) both springs always have right hand helix (B) both springs always have left hand helix (C) both springs always have opposite hand of helices (D) any of the above

Description : A concentric spring consist of two helical compression springs (A) both springs always have right hand helix (B) both springs always have left hand helix (C) both springs always have opposite hand of helices (D) any of the above

Last Answer : (C) both springs always have opposite hand of helices

The type of spring used to achieve greater load carrying capacity within given space is (A) Spiral spring (B) Springs in series (C) Multi-leaf spring (D) Concentric springs

Description : The type of spring used to achieve greater load carrying capacity within given space is (A) Spiral spring (B) Springs in series (C) Multi-leaf spring (D) Concentric springs

Last Answer : (D) Concentric springs

If `A=(x : x=4n+1,nle5,n in N}` and `B={3n : n le 8, n in N}`, then find `(A-(A-B))`.

Description : If `A=(x : x=4n+1,nle5,n in N}` and `B={3n : n le 8, n in N}`, then find `(A-(A-B))`.

Last Answer : If `A=(x : x=4n+1,nle5,n in N}` and `B={3n : n le 8, n in N}`, then find `(A-(A-B))`.

For two springs connected in parallel, net force is equal to the sum of force in each spring. a) True b) False

Description : For two springs connected in parallel, net force is equal to the sum of force in each spring. a) True b) False

Last Answer : a) True

When two Belleville springs are in parallel, half force is obtained for a given deflection. (a) Half force (b) Double force (c) Same force (d) Can’t be determined

Description : When two Belleville springs are in parallel, half force is obtained for a given deflection. (a) Half force (b) Double force (c) Same force (d) Can’t be determined

Last Answer : (b) Double force

Why are mechanical springs used? a. To apply force b. To store energy c. To measure force d. All of the above

Description : Why are mechanical springs used? a. To apply force b. To store energy c. To measure force d. All of the above

Last Answer : d. All of the above

What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Last Answer : c. 20.120 N/mm2

What is the moment of inertia acting on a circle of diameter 50 mm? a. 122.71 x 103 mm4 b. 306.79 x 103 mm4 c. 567.23 x 103 mm4 d. 800 x 103 mm4

Description : What is the moment of inertia acting on a circle of diameter 50 mm? a. 122.71 x 103 mm4 b. 306.79 x 103 mm4 c. 567.23 x 103 mm4 d. 800 x 103 mm4

Last Answer : b. 306.79 x 103 mm4

Can concentric springs be used to obtain a force which is not proportional to its deflection? a) True b) False

Description : Can concentric springs be used to obtain a force which is not proportional to its deflection? a) True b) False

Last Answer : a) True

What is 2n times 3n?

Description : What is 2n times 3n?

Last Answer : 6n²example if n=5(2x5) x (3x5) = 10 x 15 = 1506 x 5² = 6 x 25 = 150

If input frequency of a full wave rectifier be n, then output frequency would be - (1) n/2 (2) n (3) 3n/2 (4) 2n

Description : If input frequency of a full wave rectifier be n, then output frequency would be - (1) n/2 (2) n (3) 3n/2 (4) 2n

Last Answer : (4) 2n Explanation: The frequency of a full-wave rectifier is double that of the input, if the input is a sine wave. A full-wave rectifier converts the whole of the input waveform to one ... both polarities of the input waveform to DC (direct current), and yields a higher mean output voltage.

................... comparisons are necessary in the worst case to find both the maximum and minimum of n numbers. (A) 2n-2 (B) n + floor(lg n) - 2 (C) floor(3n/2) - 2 (D) 2 lg n – 2

Description : ................... comparisons are necessary in the worst case to find both the maximum and minimum of n numbers. (A) 2n-2 (B) n + floor(lg n) - 2 (C) floor(3n/2) - 2 (D) 2 lg n – 2

Last Answer : (C) floor(3n/2) - 2

-For two shafts in parallel or for two concentric shafts a. T = T1 + T2 b. T = T1 = T2 c. T = T1 – T2 d. T = (T1.T2)^1/2

Description : -For two shafts in parallel or for two concentric shafts a. T = T1 + T2 b. T = T1 = T2 c. T = T1 – T2 d. T = (T1.T2)^1/2

Last Answer : a. T = T1 + T2

A spring of stiffness 100 N/mm used in a spring-loaded safety valve of diameter 20 mm on a boiler with the pressure inside the boiler equal to 1 MPa should be initially compressed by a. 5mm b. 3.14 mm c. 2mm d. 6.28 mm

Description : A spring of stiffness 100 N/mm used in a spring-loaded safety valve of diameter 20 mm on a boiler with the pressure inside the boiler equal to 1 MPa should be initially compressed by a. 5mm b. 3.14 mm c. 2mm d. 6.28 mm

Last Answer : b. 3.14 mm

Stiffness of the spring can be increased by a. increase the number of turns b. increase the free length c. decrease the number of turns d. decrease the spring wire diameter

Description : Stiffness of the spring can be increased by a. increase the number of turns b. increase the free length c. decrease the number of turns d. decrease the spring wire diameter

Last Answer : c. decrease the number

Compute the maximum shearing stress developed in a phosphor bronze spring having mean diameter of 200 mm and consisting of 24 turns of 20-mm diameter wire when the spring is stretched 100 mm. and G = 42 GPa. a. 51 MPa b. 31.89 MPa c. 80 MPa d. 70 MPa

Description : Compute the maximum shearing stress developed in a phosphor bronze spring having mean diameter of 200 mm and consisting of 24 turns of 20-mm diameter wire when the spring is stretched 100 mm. and G = 42 GPa. a. 51 MPa b. 31.89 MPa c. 80 MPa d. 70 MPa

Last Answer : b. 31.89 MPa

A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing stress of 124 N/mm2. G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Description : A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing ... G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Last Answer : a. 10 turns

Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm

Description : Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm

Last Answer : b. 105.4 mm

A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number of active coils is 10. If the mean coil diameter is reduced to 10 mm, the stiffness of the spring is approximately a. increased by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Description : A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number ... by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Last Answer : a. increased by 8 times

The spring constant of a helical compression spring does not depend on a. Coil diameter b. Material strength c. Number of active turns d. wire diameter

Description : The spring constant of a helical compression spring does not depend on a. Coil diameter b. Material strength c. Number of active turns d. wire diameter

Last Answer : b. Material strength

Determine number of coils in a helical compression spring, if modulus of rigidity is 80 Gpa and spring stiffness is 50 N/ mm. Assume wire diameter and spring index as 8 mm and 5 respectively a. 11.8 turns b. 12.8 turns c. 13.3 turns d. None of the above

Description : Determine number of coils in a helical compression spring, if modulus of rigidity is 80 Gpa and spring stiffness is 50 N/ mm. Assume wire diameter and spring index as 8 mm and 5 respectively a. 11.8 turns b. 12.8 turns c. 13.3 turns d. None of the above

Last Answer : b. 12.8 turns

The product of the tangential force acting on the shaft and radius of shaft known as (a) Torsional rigidity (b) Flexural rigidity (c) Bending moment (d) Twisting moment

Description : The product of the tangential force acting on the shaft and radius of shaft known as (a) Torsional rigidity (b) Flexural rigidity (c) Bending moment (d) Twisting moment

Last Answer : (d) Twisting moment