Spiral spring is quite rigid.
(a) Yes (b) No it is flexible (c) It is of moderate rigidity (d) Rigidity can’t be  determined

1 Answer

Answer :

(b) No it is flexible

Related questions

Description : Spiral spring is quite rigid. a) Yes b) No it is flexible c) It is of moderate rigidity d) Rigidity can’t be determined

Last Answer : b) No it is flexible

Description : Flexible shafts have ______ rigidity in bending moment. a) High b) Low c) Very high d) Extremely low

Last Answer : b) Low

Description : Flexible shafts have ___ rigidity in torsion making them flexible. a) Low b) High c) Very high d) Infinitely small

Last Answer : b) High

Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can't be determined

Last Answer : (b) 4674.1N

Description : The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity

Last Answer : b) Spring stiffness

Description : Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Last Answer : a) 7

Description : Determine number of coils in a helical compression spring, if modulus of rigidity is 80 Gpa and spring stiffness is 50 N/ mm. Assume wire diameter and spring index as 8 mm and 5 respectively a. 11.8 turns b. 12.8 turns c. 13.3 turns d. None of the above

Last Answer : b. 12.8 turns

Description : The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity

Last Answer : (b) Spring stiffness

Description : The type of spring used to achieve any linear and non-linear load-deflection characteristics is (a)spiral spring (b) non-ferrous spring (c)Belleville spring (d) torsion spring

Last Answer : (c)Belleville spring

Description : The type of spring used to achieve greater load carrying capacity within given space is (a)spiral spring (b) springs in series (c)multi-leaf spring (d) concentric spring

Last Answer : (d) concentric spring

Description : There are number of laminations in a (a) Close coiled spring (b) Open coiled spring (c) Spiral spring (d) None

Last Answer : (d) None

Description : The strain energy stored in a spiral spring is given by? (a) 12M²L/Ebtᵌ (b) 6M²L/Ebtᵌ (c) 8M²L/Ebtᵌ (d) None of the listed

Last Answer : (b) 6M²L/Ebtᵌ

Description : The spring used in mechanical toys is (a) Leaf spring (b) Spiral spring (c) Helical spring (d) All of these

Last Answer : (b) Spiral spring

Description : A spring used to absorb shocks and vibrations is (a) Close-coil helical spring (b) Open coiled helical spring (c) Spiral spring (d) Leaf spring

Last Answer : (d) Leaf spring

Description : There are number of laminations in a (a) Close coiled spring (b) Open coiled spring (c) Spiral spring (d) None

Last Answer : (d) None

Description : The spring used in mechanical toys is (a) Leaf spring (b) Spiral spring (c) Helical spring (d) All of these

Last Answer : (b) Spiral spring

Description : A spring used to absorb shocks and vibrations is (a) Close-coil helical spring (b) Open coiled helical spring (c) Spiral spring (d) Leaf spring

Last Answer : d) Leaf spring

Description : In the theorem of three moments in the most general form a.two flexural rigidity are considered b. only one flexural rigidity is considered c.no flexural rigidity is considered d.flexural rigidity is doubled

Last Answer : a.two flexural rigidity are considered

Description : When two Belleville springs are in parallel, half force is obtained for a given deflection. (a) Half force (b) Double force (c) Same force (d) Can’t be determined

Last Answer : (b) Double force

Description : A simply supported beam carries uniformly distributed load of 20 kN/m over the length of 5 m. If flexural rigidity is 30000 kN.m2, what is the maximum deflection in the beam? a. 5.4 mm b. 1.08 mm c. 6.2 mm d. 8.6 mm

Last Answer : a. 5.4 mm

Description : The shafts will have same strength on the basis of torsional rigidity, if (a) diameter and length of both shafts is same (b) material of both shafts is same (c) angle of twist for both shafts is same (d) all of above conditions are satisfied

Last Answer : (d) all of above conditions are satisfied

Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm². a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Last Answer : b) 41.2mm

Description : While designing shaft on the basis of torsional rigidity, angle of twist is given by? a) 100Ml/Gd⁴ b) 584Ml/Gd⁴ c) 292 Ml/Gd⁴ d) 300 Ml/Gd⁴

Last Answer : b) 584Ml/Gd⁴

Description : A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of ... shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Last Answer : (a) 43 to 45

Description : A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Last Answer : (d) 27/p

Description : In the relation ( T/J = Gθ/L = τ/ R), the letter G denotes modulus of ______ a. elasticity b. plasticity c. rigidity d. resilience

Last Answer : c. rigidity

Description : What is the S.I. unit of torsional rigidity? a. Nm b. N.m2 c. Nm/ radian d. None of the above

Last Answer : b. N.m2

Description : The product of the tangential force acting on the shaft and radius of shaft known as (a) Torsional rigidity (b) Flexural rigidity (c) Bending moment (d) Twisting moment

Last Answer : (d) Twisting moment

Description : .The shafts are designed on the basis of (a) Rigidity (b) Strength (c) Both of these (d) Either of these

Last Answer : (c) Both of these

Description : Strength of a shaft a. Is equal to maximum shear stress in the shaft at the time of elastic failure b. Is equal to maximum shear stress in the shaft at the time of rupture c. Is equal to torsional rigidity d. Is ability to resist maximum twisting moment

Last Answer : d. Is ability to resist maximum twisting moment

Description : Torsional rigidity is defined as a. T/θ b. Cθ c. CIp d. = θ

Last Answer : c. CIp

Description : Which of the following is incorrect? a. In torsion equation, we use mean torque b. In torsion equation, we use maximum torque c. Many shafts are designed under combined bending and torsion load d. Shafts are also designed for torsional rigidity

Last Answer : a. In torsion equation, we use mean torque

Description : The shafts are designed on the basis of a. strength and rigidity. b. ductility. c. malleablility. d. resilience.

Last Answer : a. strength and rigidity.

Description : Torsional rigidity of a shaft is given by a. Gl/θ b. Tθ c. Tl/θ d. T/l

Last Answer : c. Tl/θ

Description : Torsional rigidity of a shaft is defined as a. G/J b. GJ c. TJ d. T/J

Last Answer : a. G/J

Description : What is the product of sectional modulus and allowable bending stress called as? a. Moment of inertia b. Moment of rigidity c. Moment of resistance d. Radius of gyration

Last Answer : c. Moment of resistance

Description : Percentage elongation during tensile test is indication of (a) Ductility (b) Malleability (c) Creep (d) Rigidity

Last Answer : (a) Ductility

Description : The ratio of lateral strain to linear strain is called (a) Modulus of Elasticity (b) Modulus of Rigidity (c) Bulk Modulus (d) Poisson’s Ratio

Last Answer : (d) Poisson’s Ratio

Description : The relationship between Young’s modulus (E), Modulus of rigidity (C) and Bulk modulus (K) is given by a. E=9CK/(C+3K) b. E=9CK/(2C+3K) c. E=9CK/(3C+K) d. E=9CK/(C-3K)

Last Answer : a. E=9CK/(C+3K)

Description : Modulus of rigidity is (a)Tensile stress / Tensile strain (a)Shear stress / Shear strain (a)Tensile stress / Shear strain (a)Shear stress / Tensile strain

Last Answer : (a)Shear stress / Shear strain

Description : Cylinder having inner diameter to wall thickness ratio less than 15 are a) Thin cylinders b) Thick Cylinders c) Moderate cylinders d) none of the above

Last Answer : b) Thick Cylinders

Description : If spring index=2.5, what can be concluded about stresses in the wire? a) They are high b) They are negligible c) They are moderate d) Cannot be determined

Last Answer : a) They are high

Description : Flexible shafts have ______ rigidity in bending moment. a) High b) Low c) Very high d) Extremely low

Last Answer : b) Low

Description : Flexible shafts have _______ rigidity in torsion making them flexible. a) Low b) High c) Very high d) Infinitely small

Last Answer : b) High

Description : Flexible shafts have ______ rigidity in bending moment. a) High b) Low c) Very high d) Extremely low

Last Answer : b) Low

Description : There is a problem of alignment in deep groove ball bearings. (a) Yes (b) No, it is self-aligning (c) It aligns itself only in some particular cases (d) Can’t be determined

Last Answer : (a) Yes

Description : There is problem of alignment in deep groove ball bearings. a) Yes b) No, it is self-aligning c) It aligns itself only in some particular cases d) Can’t be determined

Last Answer : a) Yes

Description : Set screws are subjected to tensile forces only. a) Yes b) No, they are subjected to compressive forces only c) Both compressive and tensile d) Can’t be determined

Last Answer : b) No, they are subjected to compressive forces only

Description : Indian Constitution is - (1) Rigid (2) Flexible (3) Neither rigid nor flexible (4) Partly rigid and partly flexible

Last Answer : (3) Neither rigid nor flexible Explanation: Indian constitution is neither rigid nor flexible.

Description : Government is classified as parliamentary and presidential on the basis of which of the following? (1) Relations between legislature and executive (2) Relations between politician and civil servants (3) Written or unwritten Constitutions (4) Rigid or Flexible Constitutions

Last Answer : (1) Relations between legislature and executive Explanation: Government is classified as parliamentary and presidential on the basis of relations between legislatures and executive.