Photo diode operates in the _______ condition (a) Forward bias (b) null (c) both a & d (d) reverse bias

Photo diode operates in the _______ condition
(a) Forward bias (b) null (c) both a & d (d) reverse bias
by

1 Answer

Answer :

(d) reverse bias
by

Related questions

Junction breakdown occurs: a) With forward bias b) With reverse bias c) Under high temperature condition d) Because of excess heating of the diode

Description : Junction breakdown occurs: a) With forward bias b) With reverse bias c) Under high temperature condition d) Because of excess heating of the diode

Last Answer : Ans: B

When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an ____________. A. open B. short C. good resistive quality D. good capacitive quality

Description : When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an ____________. A. open B. short C. good resistive quality D. good capacitive quality

Last Answer : Answer: B

A device used to avoid the relay destroying the op-amp is A. diode B. LED C. reverse bias diode D. forward biased diode

Description :  A device used to avoid the relay destroying the op-amp is A. diode B. LED C. reverse bias diode D. forward biased diode

Last Answer : reverse bias diode

Avalanche breakdown in a diode occurs when a. Potential barrier is reduced to zero. b. Forward current exceeds certain value. c. Reverse bias exceeds a certain value. d. None of these

Description : Avalanche breakdown in a diode occurs when a. Potential barrier is reduced to zero. b. Forward current exceeds certain value. c. Reverse bias exceeds a certain value. d. None of these

Last Answer : c. Reverse bias exceeds a certain value.

Define i)P-N junction diode ii) Depletion layer iii)Forward bias iv)Reverse bias of P-N junction diode

Description : Define i)P-N junction diode ii) Depletion layer iii)Forward bias iv)Reverse bias of P-N junction diode

Last Answer : i)P-N junction diode: It is a semiconductor device in which half of its region is P-type and other half is N-type.  ii) Depletion layer: The region where free electrons and free holes are absent ... and negative terminal is connected to p-side of p-n junction diode, it is said to be reverse bias.

Process of conversion low voltage to high voltage is called _______ (a) Rectification (b)forward bias (c) reverse bias (d) amplification

Description : Process of conversion low voltage to high voltage is called _______ (a) Rectification (b)forward bias (c) reverse bias (d) amplification

Last Answer : (d) amplification

A combination of N-type and P-type material is called a) Diode b) Transistor c) Resistor d) Capacitor

Description : A combination of N-type and P-type material is called a) Diode b) Transistor c) Resistor d) Capacitor

Last Answer : a) Diode

The emission of number of photo electrons depends upon a) The colour of the body b) The frequency of incident light c) The intensity of light d) All of the above

Description : The emission of number of photo electrons depends upon a) The colour of the body b) The frequency of incident light c) The intensity of light d) All of the above

Last Answer : c) The intensity of light

Both LEDs and ILDs operate correctly with ∙ A. forward bias ∙ B. reverse bias ∙ C. neither forward nor reverse bias ∙ D. either forward or reverse bias

Description : Both LEDs and ILDs operate correctly with ∙ A. forward bias ∙ B. reverse bias ∙ C. neither forward nor reverse bias ∙ D. either forward or reverse bias

Last Answer : A. forward bias

Both LEDs and ILDs operate correctly with ∙ a. Forward bias ∙ b. Reverse bias ∙ c. Neither A or B ∙ d. Either A or B

Description : Both LEDs and ILDs operate correctly with ∙ a. Forward bias ∙ b. Reverse bias ∙ c. Neither A or B ∙ d. Either A or B

Last Answer : a. Forward bias

On increasing the reverse bias to a large value in a p-n junction diode current (a) Increases slowly (b) Remains fixed (c) Suddenly increases (d) Decreases slowly

Description : On increasing the reverse bias to a large value in a p-n junction diode current (a) Increases slowly (b) Remains fixed (c) Suddenly increases (d) Decreases slowly

Last Answer : (c) Suddenly increases

When a reverse bias is applied to a diode, it will a. Raise the potential barrier b. Lower the potential barrier c. Increases the majority-carrier a current greatly d. None of these

Description : When a reverse bias is applied to a diode, it will a. Raise the potential barrier b. Lower the potential barrier c. Increases the majority-carrier a current greatly d. None of these

Last Answer : a. Raise the potential barrier

Explain with neat sketch construction of PIN Diode. Draw its characteristics in reverse bias mode.

Description : Explain with neat sketch construction of PIN Diode. Draw its characteristics in reverse bias mode. 

Last Answer : Construction A PIN diode is made up of three semiconductor materials; two heavily doped P- and N- type material separated by an intrinsic (undoped) semiconductor (I) as shown in above figure ... . This advantage allows the PIN diode to process even weak signals.  Characteristics

A diode in which the change in reverse bias voltage varies the capacitance is called as

Description : A diode in which the change in reverse bias voltage varies the capacitance is called as A) Varactor diode B) Switching diode C) Tunnel diode D) Zener-diode  

Last Answer : A diode in which the change in reverse bias voltage varies the capacitance is called as Varactor diode

When reverse bias is applied to a junction diode, it

Description : When reverse bias is applied to a junction diode, it  1.increases the potential barrier 2.decreases the potential barrier 3.greatly increases the minority carrier current 4.greatly increases the majority carrier current 

Last Answer : When reverse bias is applied to a junction diode, it increases the potential barrier 

State condition for resonance in R-L-C series circuit.

Description : State condition for resonance in R-L-C series circuit.

Last Answer : The condition for resonance in R-L-C series circuit. i) Inductive Reactance should be equal to capacitive reactance. That is XL = XC ii) The power factor of the circuit is Cos ɸ = 1 iii)The voltage and ... and given by I =V/R. v)Impedance of the circuit is minimum and given by Z =R.

Explain the forward bias characteristics of a P-N Junction diode.

Description : Explain the forward bias characteristics of a P-N Junction diode. 

Last Answer : forward and reverse characteristics of P-N junction diode.

To turn a UJT ON, the forward bias on emitter diode should be:

Description : To turn a UJT ON, the forward bias on emitter diode should be:  1. more than the peak point voltage 2. less than the peak point voltage 3. Equal to the peak point voltage 4. Equal to the stand - off voltage  

Last Answer : To turn a UJT ON, the forward bias on emitter diode should be: more than the peak point voltage 

How much time a diode takes to switch ON in forward bias

Description : How much time a diode takes to switch ON in forward bias condition.

Last Answer : t=0 sec.

can zener diode be used in forward bias?

Last Answer : Yes it can be, and it will act like a normal PN junction diode. The characteristic of ZENER diode is exactly same as PN junction diode in forward Bias.

The ability of materials to become polarized under an applied electric field is called _______

Description : The ability of materials to become polarized under an applied electric field is called _______ A) Ferroelectricity B) Paraelectricity C) Polectricity D) None of these

Last Answer : The ability of materials to become polarized under an applied electric field is called Paraelectricity

In the illustration, the small battery and Rb are in the circuit to apply ________. EL-0022 A. forward bias to the emitter-base B. reverse bias to the emitter-base C. a 'reference charge' on the input capacitor D. a buffer between the input ground and the emitter ground

Description : In the illustration, the small battery and Rb are in the circuit to apply ________. EL-0022 A. forward bias to the emitter-base B. reverse bias to the emitter-base C. a 'reference charge' on the input capacitor D. a buffer between the input ground and the emitter ground

Last Answer : Answer: A

In the illustration, the large battery and R(L) are in the circuit to ________. EL-0022 A. forward bias the emitter-base B. reverse bias the emitter-base C. forward bias the emitter/collector D. reverse bias the emitter/collector

Description : In the illustration, the large battery and R(L) are in the circuit to ________. EL-0022 A. forward bias the emitter-base B. reverse bias the emitter-base C. forward bias the emitter/collector D. reverse bias the emitter/collector

Last Answer : Answer: D

Photodiodes operate properly with ∙ A. forward bias ∙ B. reverse bias ∙ C. neither forward nor reverse bias ∙ D. either forward or reverse bias

Description : Photodiodes operate properly with ∙ A. forward bias ∙ B. reverse bias ∙ C. neither forward nor reverse bias ∙ D. either forward or reverse bias

Last Answer : ∙ B. reverse bias

Photodiodes operate property with ∙ a. Forward bias ∙ b. Reverse bias ∙ c. Neither A or B ∙ d. Either A or B

Description : Photodiodes operate property with ∙ a. Forward bias ∙ b. Reverse bias ∙ c. Neither A or B ∙ d. Either A or B

Last Answer : ∙ b. Reverse bias

Depletion region of a junction is formed _________ (a) during the manufacturing process (b) under forward bias (c) under reverse bias (d) when temperature varies

Description : Depletion region of a junction is formed _________ (a) during the manufacturing process (b) under forward bias (c) under reverse bias (d) when temperature varies

Last Answer : (a) during the manufacturing process

What is the difference between forward and reverse bias?

Description : What is the difference between forward and reverse bias?

Last Answer : Forward bias is a PN junction bias which allows current to flow through the junction. Forward bias decreases the resistance of the depletion layer. Reverse bias is a PN junction bias that allows only ... Positive polarity on the n-type material and negative polarity to the p-type material.

While testing a semi-conductor diode with an ohmmeter, both the forward and reverse readings are almost in the infinity range. This would indicate that the unit is _____________. A. good B. open C. grounded D. shorted

Description : While testing a semi-conductor diode with an ohmmeter, both the forward and reverse readings are almost in the infinity range. This would indicate that the unit is _____________. A. good B. open C. grounded D. shorted

Last Answer : Answer: B

Q-6 which innovative welding technique is used by L & T in T joint welding?

Description : Q-6 which innovative welding technique is used by L & T in T joint welding?

Last Answer : In T joint welding backing is required in other side while welding on one side. Flux goes on another side from the root opening and that has to be removed before welding other side. During the ... of the job is also not required by other sources since one side of welding serve the purpose.

List out any four effects of electric current used in measuring instruments & write name of meter working on it.

Description : List out any four effects of electric current used in measuring instruments & write name of meter working on it.

Last Answer : Effects of Electric Current used in measuring instruments:  1. Magnetic Effect: PMMC and Moving Iron type Ammeters, voltmeter and Dynamometer type wattmeters etc.  2. Electromagnetic induction ... . Electrostatic effect: Voltmeters.  5. Hall Effect: Flux meter, Poynting vector wattmeter.

Please solve Figure 1&2 just by KVL and also requesting to solve Fig-3 & 4 also.

Description : I am a new student of electrical and electronic engineering, and facing some problems on sign related, kvl as well as mesh current analysis. By getting solution of these problems, I may get rid of these ... For figure 4, please just write the seven mesh equations only, solution is not needed.

Last Answer : u can assume the direction of current either in clockwise or anticlockwise...but the solution will remain same in both cases

Q-10 In TANDEM SAW process, why AC and DC both currents are used?

Description : Q-10 In TANDEM SAW process, why AC and DC both currents are used?

Last Answer : AC will melt the base metal and make weld pool in the base metal and by DC it will fill the weld metal in the weld pool.

Q-9 how many electrodes are used in the TANDEM SAW? What is the polarity of the both electrode?

Description : Q-9 how many electrodes are used in the TANDEM SAW? What is the polarity of the both electrode?

Last Answer : In TANDEM SAW process there are more than one electrode is used. But for first electrode alternative current and for second electrode direct current shall be used.

The output of two inputs OR gate is zero only when: (a) Both are one (b) Both are zero (c) Either input is 1 (d) None

Description : The output of two inputs OR gate is zero only when: (a) Both are one (b) Both are zero (c) Either input is 1 (d) None

Last Answer : (b) Both are zero

An electric motor in which both stator field and rotor rotates with same speed is called?

Description : An electric motor in which both stator field and rotor rotates with same speed is called?

Last Answer : An electric motor in which both stator field and rotor rotates with same speed is called synchronous motor.

Describe the working of PN junction diode with neat sketch under forward biased condition.

Description : Describe the working of PN junction diode with neat sketch under forward biased condition.

Last Answer : If the p-region (anode) is connected to the positive terminal of the external DC source and nside (cathode) is connected to the negative terminal of the DC source then the biasing ... The large number of majority carriers crossing the junction constitutes a current called as the forward current.

Compressor wizards, share your wisdom?

Description : Compressor wizards, share your wisdom?

Last Answer : There is this chap that bought a small compressor for electronics dusting purposes and compared it to a normal blower style duster. The compressor was a complete failure.

How would you handle UPS packages with this setup?

Description : How would you handle UPS packages with this setup?

Last Answer : Pick them up from the depot…

Q-12 which Testing is used in high thickness job in LNT?

Description : Q-12 which Testing is used in high thickness job in LNT?

Last Answer : Ultrasonic Testing.

Q-11 What is the purpose of dust free zone in LNT?

Description : Q-11 What is the purpose of dust free zone in LNT?

Last Answer : Special dust-free enclosures with temperature and humidity control enable the Company to achieve manufacturing excellence in Class 1 nuclear island components. L&T manufactures reactor vessels, steam ... and Heat Exchangers are manufactured within dust-free enclosures at L&T's workshops.

Q-8 which types of SAW process are used in Larsen and Toubro?

Description : Q-8 which types of SAW process are used in Larsen and Toubro?

Last Answer : Tandem SAW Narrow groove application As the section thickness of vessel for nuclear and petroleum industry increase, the desire for reduced weld time and material consumption has driven the joint on ... process is carried out. LNT practice that for many of high thickness nuclear pressure vessel.

Q-7 during welding process, why sinusoidal wave form is converted in to the square wave form?

Description : Q-7 during welding process, why sinusoidal wave form is converted in to the square wave form?

Last Answer : In sinusoidal wave, we get maximum energy at one point only. So for the more amount of maximum energy we can get by converting the sinusoidal wave form in to the square wave form, and more penetration and deposition rate is achieved due to maximum energy.

Q-5 what is the phenomena behind the overhead welding?

Description : Q-5 what is the phenomena behind the overhead welding?

Last Answer : In overhead welding during welding flux has more fluidity and comes on the surface when the metal is deposited in the root gape. There are different freezing point metal and the flux. so metal have low ... deposit in the root gape and flux have a high freezing point so its deposit on the metal .

Q -4 what is the purpose of sodium, silicon and potassium in core element?

Description : Q -4 what is the purpose of sodium, silicon and potassium in core element?

Last Answer : • Silicon - deoxidize & form slag • Sodium - stabilize arc & form slag • Potassium - stabilizes the arc & form slag

Q-3 Write the energy distribution for different polarity?

Description : Q-3 Write the energy distribution for different polarity?

Last Answer : DCEP – 67% at electrode and 33% at job. • DCEN – 33 % at electrode and 67% at job. • AC – 50 % at electrode and 50% job.

Q-2 what are the functions of electrode covering in SMAW process?

Description : Q-2 what are the functions of electrode covering in SMAW process?

Last Answer : To facilitate arc ignition and give arc stability. To generate gas for shielding the arc & molten metal from air contamination. To de-oxidise the weld metal and flux impurities into the slag. To ... to support the molten weld metal). To control hydrogen contents in the weld. (basic type)

Q-1 what is the function of copper coating in SAW filler wire?

Description : Q-1 what is the function of copper coating in SAW filler wire?

Last Answer : to assure a good electric contact between wire and contact tip • to assure a smooth feed of the wire through the guide tube, feed rolls and contact tip (decrease contact tube wear) • to provide protection against corrosion

at the terminal of a three-phase 6.6Kv alternator a load R=200 ohm is connected between two-phase and the third phase is opened. Z1=z2=5 ohm Zo=2 find out the fault current .

Description : at the terminal of a three-phase 6.6Kv alternator a load R=200 ohm is connected between two-phase and the third phase is opened. Z1=z2=5 ohm Zo=2 find out the fault current .

Last Answer : 32A

Black body radiations depends upon a) The shape and nature of the body b) The velocity of radiations and colour of the body c) The temperature of the body d) All of the above

Description : Black body radiations depends upon a) The shape and nature of the body b) The velocity of radiations and colour of the body c) The temperature of the body d) All of the above

Last Answer : c) The temperature of the body