The operational amplifier is _______
(a) High gain amplifier (b) high power amplifier
(c)high resistance amplifier (d)low resistance amplifier

1 Answer

Answer :

a) High gain amplifier

Related questions

Description : The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter

Last Answer : (d) inverter

Description : Non-inverting amplifier circuits have _______ (a) Very high input impedance (b) very low input impedance (c) low output impedance (d) none of above

Last Answer : (a) Very high input impedance

Description : The gain G of non-inverting amplifier is (a) G = − R2 R1 (b) G = 1 + R2 R1 (c) G = R2

Last Answer : (b) G = 1 + R2 R1

Description : SI unit of gain of amplifier is (a) Volt (b) ampere (c) coulomb (d) dimensionless

Last Answer : (d) dimensionless

Description : The open loop gain of the amplifier is ______ (a) 105 (b) 103 (c) 106 (d) 108

Last Answer : (a) 105

Description : The electronic circuits which implement the various logic operations are called ________ (a) Logic gates (b) Boolean algebra (c) amplifier gain (d) logic functions

Last Answer : a) Logic gates

Description : Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages

Last Answer : Answer: C

Description : The circuit shown in the illustration functions as a ____________. EL-0087 A. pulse trigger circuit for an operational amplifier B. three stage, high gain class 'A' amplifier C. binary ripple counter or shift register D. free running multivibrator

Last Answer : Answer: C

Description : An operational amplifier, as used in today's consoles, has a calculated gain of 5. This means that when the input changes _____________. A. 5 volts, the output changes 10 volts B. 10 volts, the output changes 5 volts C. 2 volts, the output changes 10 volts D. 10 volts, the output changes 2 volts

Last Answer : Answer: C

Description : An operational amplifier, as used in today's consoles, may have a calculated gain of 5. This means that as the input changes by ______________. A. 1 volt, the output changes 5 volts B. 5 volts, the output changes 1 volt C. 5 volts, the output changes 10 volts D. 10 volts, the output changes 5 volts

Last Answer : Answer: A

Description : If the unity-gain point of the operational amplifier used in question 24 is 500 kilohertz, what is the bandwidth of the circuit?

Last Answer : 50 kilohertz (Gain = 10; Gain-Bandwidth Product = 500,000) 500,000(Hz)

Description : An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is  A) 25 micro-volt B) 50 micro-volt C) 5 Volts D) 10 volts

Last Answer : An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is 50 micro-volt

Description : In the ideal closed loop operational amplifier, the gain depends on (A) value of the series component (B) value of the feedback component (C) on the operational amplifier itself (D) both A and B

Last Answer : In the ideal closed loop operational amplifier, the gain depends on (A) value of the series component (B) value of the feedback component (C) on the operational amplifier itself (D) both A and B

Description : The effect of a finite gain of an operational amplifier used in an integrator is that (A) it would not integrate (B) the slope of the output will vary with time (C) the final value of the output voltage will reduce (D) there will be instability in the circuit

Last Answer : The effect of a finite gain of an operational amplifier used in an integrator is that there will be instability in the circuit

Description : Process of conversion low voltage to high voltage is called _______ (a) Rectification (b)forward bias (c) reverse bias (d) amplification

Last Answer : (d) amplification

Description : What is the speaker driving voltage of an amplifier?

Last Answer : I have to ask WHY? That said, Speakers and a light bulb are two different types of load, and the the lights will probably fry the output transistor.

Description : One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Last Answer : d. To prevent reradiation of the local oscillator

Description : Operational amplifiers, used primarily in analog circuits, are characterized by ____________. A. high input impedance, high gain and low output impedance B. high input impedance, high gain and high output ... gain and high output impedance D. low input impedance, high gain and low output impedance

Last Answer : Answer: A

Description : _______ electric power is the most common method used by electrical grids to transfer power.  (A) One-phase (B) Two-phase (C) Three-phase (D) None of the above

Last Answer : Three-phase electric power is the most common method used by electrical grids to transfer power. 

Description : To provide its unique characteristics to analog circuits, the operational amplifier is made up of a/an ______________. A. voltage amp, current amp and output amp B. input amp, power amp and output amp C. scaling amp, power amp and voltage amp D. differential amp, voltage amp and output amp

Last Answer : Answer: D

Description : The circuit shown in the illustration represents a/an ____________. EL-0085 A. operational amplifier B. Wheatstone bridge C. magnetic amplifier D. power supply

Last Answer : Answer: D

Description : In a resistance loaded amplifier, the gain decreases a high frequencies because A) Of decreasing reactance of the stray CT B) Increasing reactance of the stray CT C) Increasing reactance of CC D) Decreasing reactance of CC.

Last Answer : D) Decreasing reactance of CC.

Description : Cassegrain feedis usedwith a parabolic reflectorto a. increase the gain of the system b. increase the beamwidth of the system c. reduce the size of the main reflector d. allowthe feedtobeplacedata convenientpoint

Last Answer : d. allowthe feedtobeplacedata convenientpoint

Description : The standard reference antenna forthe directive gain isthe a. infinitesimal dipole b. isotropic antenna c. elementary doublet d. half-wave dipole

Last Answer : b. isotropic antenna

Description : Current gain of a transistor which has collector current of 10 mA and a base current of 40 micro Ampere is: (a) 25 (b) 250 (c) 2500 (d) 25000

Last Answer : b) 250

Description : The emitter of a transistor is doped the heaviest because it: (a) Acts as a supplier of charge carriers (b) Dissipates maximum power c) has a large resistance (d) has a small resistance

Last Answer : (a) Acts as a supplier of charge carriers

Description : When an alternating current passes through an ohmic resistance the electrical power converted into heat is?

Last Answer : When an alternating current passes through an ohmic resistance the electrical power converted into heat is true power.

Description : A galvanometer having a resistance of 4.5 Ω can read up to 5 mA. If it is to read 100 V, then the high resistance to be used in series will be a) 19998 Ω b) 19995.8 Ω c) 19995.5 Ω d) 19996.5 Ω

Last Answer : c) 19995.5

Description : Desirable resistance of a ________ is achieved by connecting a high resistance Rh in series with a galvanometer a) Ammeter b) Ohmmeter c) LED d) Voltmeter

Last Answer : d) Voltmeter

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

Description : The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, ... this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Last Answer : B. 2,518 Ω

Description : An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: (1) 1/11 kΩ (2) 1/5 kΩ (3) 5 kΩ (4) 11 kΩ

Last Answer : An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: 1/11 kΩ

Description : An OP-AMPs can amplify _______ (a) D.C (b) A.C (c) both A.C & D.C (d) none of above

Last Answer : b) A.C

Description : In transistor, the base region is of the order of _______ (a) 10-5 m (b) 10-2 m (c) 10-8 m (d) 10-6 m

Last Answer : d) 10-6 m

Description : The potential barrier for germanium is _______ (a) 0.6 V (b) 0.2 V (c) 0.3 V (d) 0.5 V

Last Answer : (c) 0.3 V

Description : How can a solar array power source be bypassed when the batteries run low?

Last Answer : Ah got it. If anyone else is interested, you need an “automatic transfer switch” – or get a manual one for that mad scientist charm.

Description : What type of circuit is on card 'A0AA2' at coordinate '29Q' shown in the illustration? EL-0099 A. Operational amplifier B. Digital logic inverter C. Square wave pulse generator D. Binary counter

Last Answer : Answer: A

Description : What can be used to replace the exciter in the circuit shown in the illustration? EL-0101 A. A step-up transformer. B. A rectifier. C. A step-down transformer. D. An operational amplifier.

Last Answer : Answer: B

Description : The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an ... drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Last Answer : Answer: D

Description : Common basic applications for the operational amplifier include ____________. A. counting, pulsing and clocking amplifiers B. summing, scaling and difference amplifiers C. step-up, step-down and rectifying amplifiers D. all of the above

Last Answer : Answer: B

Description : One feature of the operational amplifier is that it can have ____________. A. up to ten outputs B. binary coded decimal inputs C. several hundred amps at the output D. inverting and non-inverting inputs

Last Answer : Answer: D

Description : The schematic symbol for an operational amplifier in an analog circuit is a _________. A. circle B. square C. trapezoid D. triangle

Last Answer : Answer: D

Description : The conversion of the throttle command voltage to the signal necessary to achieve the desired shaft RPM is accomplished by the _____________. A. ahead or astern function generator of the ... circuit C. operational amplifiers in the autorotation circuit D. long time constant amplifier circuit

Last Answer : Answer: A

Description : In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?

Last Answer : 0 volts.

Description : What does the term "closed-loop" mean in the closed-loop configuration of an operational amplifier?

Last Answer : The use of degenerative (negative) feed-back

Description : What are the three requirements for an operational amplifier?

Last Answer : . Very high gain, very high input impedance, very low output

Description : The ideal operational amplifier does not have: (1) Infinite input resistance (2) Infinite output resistance (3) Infinite voltage gain (4) Infinite bandwidth 

Last Answer : The ideal operational amplifier does not have: Infinite output resistance

Description : What is the importance of negative feedback in the operational amplifier? (A) It maintains the gain (B) The voltage difference between the input terminals is maintained at a very small value ( ... value (D) The voltage difference between the input terminals is maintained at a very high value

Last Answer : The voltage difference between the input terminals is maintained at a very small value

Description : What is operational amplifier?

Last Answer : Operational amplifier is an amplifier which amplifies the input signal when we pass a low voltage signal .It has two terminals inverting and non inverting. It is an active device because it ... of negative feedback it provides the output waveform similar to the input waveform (truely amplified )