Description : An operational amplifier, as used in today's consoles, has a calculated gain of 5. This means that when the input changes _____________. A. 5 volts, the output changes 10 volts B. 10 volts, the output changes 5 volts C. 2 volts, the output changes 10 volts D. 10 volts, the output changes 2 volts
Last Answer : Answer: C
Description : An operational amplifier, as used in today's consoles, may have a calculated gain of 5. This means that as the input changes by ______________. A. 1 volt, the output changes 5 volts B. 5 volts, the output changes 1 volt C. 5 volts, the output changes 10 volts D. 10 volts, the output changes 5 volts
Last Answer : Answer: A
Description : What type of circuit is on card 'A0AA2' at coordinate '29Q' shown in the illustration? EL-0099 A. Operational amplifier B. Digital logic inverter C. Square wave pulse generator D. Binary counter
Description : The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an ... drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor
Last Answer : Answer: D
Description : Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages
Description : Non-inverting amplifier circuits have _______ (a) Very high input impedance (b) very low input impedance (c) low output impedance (d) none of above
Last Answer : (a) Very high input impedance
Description : The operational amplifier is _______ (a) High gain amplifier (b) high power amplifier (c)high resistance amplifier (d)low resistance amplifier
Last Answer : a) High gain amplifier
Description : The circuit shown in the illustration functions as a ____________. EL-0087 A. pulse trigger circuit for an operational amplifier B. three stage, high gain class 'A' amplifier C. binary ripple counter or shift register D. free running multivibrator
Description : The termresponsivityasit appliesto a light detectorisbest described as a. the time required for the signal to go from 10 to 90 percent of maximum amplitude b.the ratio ofthediode output currentto ... of output current to output power d. the ratio of output current to input current
Last Answer : b.the ratio ofthediode output currentto opticalinputpower
Description : In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?
Last Answer : 0 volts.
Description : If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?
Last Answer : . A different shape than the input signals but larger in amplitude.
Description : If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?
Last Answer : Equal in shape and frequency to each input signal and larger in amplitude by two times than
Description : . If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?
Last Answer : No output (the signals will "cancel out").
Description : To provide its unique characteristics to analog circuits, the operational amplifier is made up of a/an ______________. A. voltage amp, current amp and output amp B. input amp, power amp and output amp C. scaling amp, power amp and voltage amp D. differential amp, voltage amp and output amp
Description : Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback
Last Answer : C) All oscillators generate sine waves
Description : The conversion of the throttle command voltage to the signal necessary to achieve the desired shaft RPM is accomplished by the _____________. A. ahead or astern function generator of the ... circuit C. operational amplifiers in the autorotation circuit D. long time constant amplifier circuit
Description : In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage
Last Answer : Answer: B
Description : In a properly functioning circuit, can both the input and output of an inverter be HIGH at the same time?
Last Answer : No.
Description : One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator
Last Answer : d. To prevent reradiation of the local oscillator
Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source
Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals
Description : If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the ... for high dc collector supply D) Clipping of output in the negative half of the input signal
Last Answer : B) Clipping of output in the positive half of the input signal
Description : If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?
Last Answer : 200 millivolts. A-18. a. Differential amplifier
Description : If only one input signal is used with a difference amplifier, what will the output signal be?
Last Answer : Equal in shape and frequency to the input signal; larger in amplitude than the input signal; half as large in amplitude as when two input signals were used that were 180 degrees out of phase.
Description : How does an inverter work?
Last Answer : An inverter converts DC supply into AC by use of electronic devices such as diodes and thyristors.
Description : EMDis best describe bywhich statement? a. 70percentofthe corediameter and70%ofthefiberNAshouldbe filled with light b.70 percent of the fiber diameter and 70% of the cone of acceptance should be filled with ... the output d.70 percent of the unwanted wavelengths should be attenuated by the fiber
Last Answer : a. 70percentofthe corediameter and70%ofthefiberNAshouldbe filled with light
Description : The magnetic flux φB through a plane element of area A⃗ in a uniform magnetic field B⃗⃗ is minimum at a) θ = 900 b) θ = 00 c) θ = 1800 d) None of these
Last Answer : a) θ = 900
Description : In inverting amplifier, the phase difference between input and output voltages must be A. 30° B. 45° C. 90° D. 180°
Last Answer : 180°
Description : For non-inverting amplifier the input and output is A. out of phase B. in phase C. have phase difference of 180° D. have phase difference of 90°
Last Answer : in phase
Description : The input and output signals of a JFET amplifier have what phase relationship?
Last Answer : They are 180 degrees out of phase.
Description : One feature of the operational amplifier is that it can have ____________. A. up to ten outputs B. binary coded decimal inputs C. several hundred amps at the output D. inverting and non-inverting inputs
Description : An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is A) 25 micro-volt B) 50 micro-volt C) 5 Volts D) 10 volts
Last Answer : An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is 50 micro-volt
Description : Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.
Last Answer : Circuit diagram:- Input / Output waveforms:-
Description : The input to an inverter is X + (YZ). What is the output
Last Answer : X + (YZ).
Description : What can be used to replace the exciter in the circuit shown in the illustration? EL-0101 A. A step-up transformer. B. A rectifier. C. A step-down transformer. D. An operational amplifier.
Description : The circuit shown in the illustration represents a/an ____________. EL-0085 A. operational amplifier B. Wheatstone bridge C. magnetic amplifier D. power supply
Description : The schematic symbol for an operational amplifier in an analog circuit is a _________. A. circle B. square C. trapezoid D. triangle
Description : If the unity-gain point of the operational amplifier used in question 24 is 500 kilohertz, what is the bandwidth of the circuit?
Last Answer : 50 kilohertz (Gain = 10; Gain-Bandwidth Product = 500,000) 500,000(Hz)
Description : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is :
Last Answer : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is : 200 V
Description : Which of the following statements are true ? I. A circuit that adds two bits, producing a sum bit and a carry bit is called half adder. II. A circuit that adds two bits, producing a sum bit and a carry bit is called full adder. ... an inverter. (A) I & II (B) II & III (C) I, II, III (D) I, III & IV
Last Answer : (D) I, III & IV
Description : If If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?
Last Answer : 200 millivolts.
Description : The electronic circuits which implement the various logic operations are called ________ (a) Logic gates (b) Boolean algebra (c) amplifier gain (d) logic functions
Last Answer : a) Logic gates
Description : The output voltage waveform of a three-phase square-wave inverter contains (A) only even harmonics (B) both odd and even harmonic (C) only odd harmonics (D) only triple harmonics
Last Answer : C
Description : Operational amplifiers, used primarily in analog circuits, are characterized by ____________. A. high input impedance, high gain and low output impedance B. high input impedance, high gain and high output ... gain and high output impedance D. low input impedance, high gain and low output impedance
Description : What is the speaker driving voltage of an amplifier?
Last Answer : I have to ask WHY? That said, Speakers and a light bulb are two different types of load, and the the lights will probably fry the output transistor.
Description : The gain G of non-inverting amplifier is (a) G = − R2 R1 (b) G = 1 + R2 R1 (c) G = R2
Last Answer : (b) G = 1 + R2 R1
Description : SI unit of gain of amplifier is (a) Volt (b) ampere (c) coulomb (d) dimensionless
Last Answer : (d) dimensionless
Description : The open loop gain of the amplifier is ______ (a) 105 (b) 103 (c) 106 (d) 108
Last Answer : (a) 105
Description : The purpose of a 'slew rate controller' in a circuit such as shown in the illustration is to ______________. EL-0096 A. limit the rate of change of a signal B. introduce a 'live zero' ... linear input into a non-linear output D. reduce air pressure to a value required by a combination circuit
Description : A temperature instrumentation system for an engine room console consists of a resistance temperature detector (RTD), a measuring bridge circuit, and a meter (or alarm circuit).Which of the following ... is zero. D. The input voltage of the resistance bridge is the constant temperature signal.
Description : In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?
Last Answer : 60 millivolts.