The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm

(A) Wien’s bridge (B) Kelvin double bridge

(C) Maxwell’s bridge (D) Shering Bridge

1 Answer

Answer :

The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm

(A) Wien’s bridge (B) Kelvin double bridge

(C) Maxwell’s bridge (D) Shering Bridge

Related questions

Description : The bridge most suited for accurate measurement of relative permittivity of dielectric materials is (A) Carey Foster Bridge (B) Anderson’s bridge (C) Heaviside Bridge modified by Campbell. (D) Schering Bridge.

Last Answer : The bridge most suited for accurate measurement of relative permittivity of dielectric materials is Schering Bridge.

Description : A dummy strain gage is used in a quarter bridge strain gage circuit to :  (A) compensate for changes in temperature and lead wire resistance  (B) produce more output voltage from the bridge  (C) increase the sensitivity of the bridge  (D) compensate lead wire resistance only

Last Answer : A dummy strain gage is used in a quarter bridge strain gage circuit to : compensate for changes in temperature and lead wire resistance 

Description : The bridge method commonly used for finding mutual inductance is (A) Heaviside Campbell bridge (B) Schering bridge (C) De Sauty bridge (D) Wien bridge

Last Answer : The bridge method commonly used for finding mutual inductance is Heaviside Campbell bridge

Last Answer : If an inductance is connected in one arm of bridge and resistances in the remaining three arms the bridge cannot be balanced.

Last Answer : In a Schering bridge the potential of the detector above earth potential is a few volts only.

Last Answer : In an Anderson bridge, the unknown inductance is measured in terms of known capacitance and resistance.

Last Answer : For measurements on high voltage capacitors, the suitable bridge is Schering bridge.

Description : A universal RLC bridge uses?

Last Answer : A universal RLC bridge uses Maxwell Wein bridge for measurement of inductance and modified De Santy's bridge for measurement of capacitance.

Description : tern null as it applies to bridge measurement.

Last Answer : Null measurements balance voltages so that there is no current flowing through the measuring device and, therefore, no alteration of the circuit being measured. Null measurements are generally more ... the use of standard voltmeters and ammeters, and they still have limits to their precision.

Description : How to Build a Bridge

Last Answer : How to Build a Bridge How to Build a Bridge Building a bridge is not an every day task, you do not see bridges going up overnight and it takes a skilled engineer to master this craft. Bridges ... this can be one of the most satisfying moments of your life to know that you have achieved your goal.

Description : How to Become a Bridge Inspector

Last Answer : How to Become a Bridge Inspector Bridge Inspectors are construction professionals who are well versed in a number of building disciplines. Among the talents of a bridge inspector are such ... secure employment in a variety of different settings, both in government agencies and private business.

Description : How to Become a Bridge Engineer

Last Answer : How to Become a Bridge Engineer Bridge Engineers are construction professionals that bear a major part of the responsibility for the safety and stability of bridges. Consequently, a bridge engineer ... new business. A well-established reputation is vital to the success of bridge engineering career.

Description : Draw circuit diagram of symmetrical configuration of bridge converter.

Last Answer : circuit diagram of symmetrical configuration of bridge converter

Description : List out advantages and disadvantages of bridge rectifier.

Last Answer : Advantages :  1. Bridge rectifier can be used in applications allowing floating output terminals i.e. not output terminal is grounded.  2. The need of center-tapped transformer is eliminated.  ... The value of the diodes used should be precise , else there will be an error in rectification

Description : Draw full bridge & half bridge configuration with common cathode.

Last Answer : Half Bridge Configuration: Full Bridge Configuration: 

Description :  operation of whetstone bridge. 

Last Answer : A Wheatstone bridge is widely used to measure the electrical resistance. This circuit is built with two known resistors, one unknown resistor and one variable resistor connected in the form of bridge. ... using a Wheatstone Bridge the unknown electrical resistance value can easily measure.

Description : Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Last Answer : Single phase fully control bridge converter with RL load: 1. During positive half cycle of input voltage, T1 and T2 are forward biased and during negative half cycle, T3 and T4 are forward biased. Therefore, T1-T2 ... cycle till the firing of next pair of SCRs as shown in the waveform.

Description : Wheatstone bridge

Last Answer : Wheatstone bridge

Description : Which of the following is true with respect to Wien Bridge? A) It does not require equal values of R or C  B) It requires that R and C values of all components must be equal C) It requires that all resistors should have equal values D) None of these

Last Answer : Which of the following is true with respect to Wien Bridge? A) It does not require equal values of R or C  B) It requires that R and C values of all components must be equal C) It requires that all resistors should have equal values D) None of these

Description : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) ... proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

Last Answer : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ directly proportional to α and inversely proportional to Φ

Description : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is (A) 4.5 V (B) 6.75 V (C) 9 V (D) 13.5 V

Last Answer : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is 9 V

Description : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is (A) sinusoidal current (B) constant dc current (C) continuous rectangular pulses (D) alternating rectangular pulses

Last Answer : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is alternating rectangular pulses

Description : Explain three phase bridge inverter.

Last Answer : Three phase bridge inverter: Three phase bridge inverter converts DC voltage input to three-phase variable frequency variable voltage output. DC voltage source can be a DC source or output of the rectifier. ... in proper sequence. The switch may be thyristor or IGBT etc.

Description : Explain the operation of full bridge converters with their different operating modes. State its advantages and disadvantages.

Last Answer : Full bridge converter: Full bridge converter provides isolation between input and output. Full bridge converter is used for step up or step down the input voltage. Full bridge converter consists of four power semiconductor ... Require filter on both input and output.

Description : explain blanking times for Bridge circuit?

Last Answer : Blanking time is provided by driver circuit to power switch. Blanking time is important because the turn on input of one transistor must be delayed with turn off input of another transistor if both ... are connected in one converter leg. This blanking time helps in avoiding cross conduction.

Last Answer : Kelvin double bridge is best suited for the measurement of: Low resistance

Description : An ammeter has a current change of 0-5A and its internal resistance is 0.2 ohm. In order to Change the range to 0-25 A, wear need to add a resistance of  A) 0.8 ohm in series with the meter B) ... series with the meter C) 0.04 ohm in parallel with the meter D) 0.05 ohm in parallel with the meter

Last Answer : An ammeter has a current change of 0—5A and its internal resistance is 0.2 ohm. In order to Change the range to 0-25 A, wear need to add a resistance of 0.05 ohm in parallel with the meter

Description : Which mass measurement is expressed in exactly four significant figures 0.001 g 0.095 g 1005 g 1000 g?

Last Answer : 1005 g

Description : A permanent magnet moving coil ammeter has a coil resistance of 99 ohm and Full Scale Deflection (FSD) current of 0.1mA. Shunt resistance is 1 ohm. Current through the meter at 0.5 F.S.D is:

Last Answer : A permanent magnet moving coil ammeter has a coil resistance of 99 ohm and Full Scale Deflection (FSD) current of 0.1mA. Shunt resistance is 1 ohm. Current through the meter at 0.5 F.S.D is: 0.05mA

Description : Weins bridge is used for measurement of frequency in the applied voltage waveform is measurement of frequency in the applied voltage waveform is   (A)sinusoidal (B) square (C) rectangular (D) triangular

Last Answer : Weins bridge is used for measurement of frequency in the applied voltage waveform is measurement of frequency in the applied voltage waveform is sinusoidal 

Last Answer : Hay’s Bridge is suitable for the measurement of: Inductances with Q>10.

Description : The device used ' for the measurement of current, voltage and resistance is: A. AVO meter B. Galvanometer C. Ammeter D. Ohm meter

Last Answer : ANSWER: A

Description : Instruments of Measure The device used ' for the measurement of current, voltage and resistance is: A. AVO meter B. Galvanometer C. Ammeter D. Ohm meter

Last Answer : ANSWER: A

Description : The device used ' for the measurement of current, voltage and resistance is: A. AVO meter B. Galvanometer C. Ammeter D. Ohm meter

Last Answer : ANSWER: A

Description : The device used ' for the measurement of current, voltage and resistance is: A. AVO meter B. Galvanometer C. Ammeter D. Ohm meter

Last Answer : ANSWER: A

Description : The measurement range of an ammeter can be increased by using a:

Last Answer : The measurement range of an ammeter can be increased by using a: low resistance in shunt

Description : When a capacitor was connected to the terminal of ohmmeter, the pointer indicated a low resistance initially and then slowly came to infinity position. This shows that capacitor is ?

Last Answer : When a capacitor was connected to the terminal of ohmmeter, the pointer indicated a low resistance initially and then slowly came to infinity position. This shows that capacitor is all right.

Description : A three-phase synchronous motor has a terminal voltage of 460 V and a terminal current of 120 A at a power factor of 0.95 lagging, synchronous reactance of 1.68 ohm and the field current is 47 A. The field to armature mutual ... _____________.      (a). 20mH   (b). 16mH   (c). 24mH   (d). 22mH

Last Answer : 22

Description : Prior to taking a resistance reading with a volt-ohm-milliammeter, the 'zero' setting must be adjusted. After clipping the two leads together, you find the adjustment knob will not return the pointer ... range setting B. weak batteries C. a faulty zero ohms knob D. a faulty meter movement

Last Answer : Answer: B

Last Answer : The absolute measurement of resistance is done by Lorenz method.

Description : An accelerometer has input range of 0 to 10g, natural frequency 30 Hz and mass 0.001 kg. The range of the secondary displacement transducer in mm required to cover the input range is (A) 0 to 2.76 (B) 0 to 9.81 (C) 0 to 11.20 (D) 0 to 52.10

Last Answer : An accelerometer has input range of 0 to 10g, natural frequency 30 Hz and mass 0.001 kg. The range of the secondary displacement transducer in mm required to cover the input range is 0 to 2.76

Description : Measurement of a non -electrical quantity involves the following four subsystems:  a) amplifier block b) display block c) instrumentation block d) transducer block  The correct, sequence in which these block occur is  (1) d,a,c,b (2) d, c, a, b (3) a, c, b, d (4) a, b, c, d

Last Answer : Measurement of a non -electrical quantity involves the following four subsystems:  a) amplifier block b) display block c) instrumentation block d) transducer block  The correct, sequence in which these block occur is d,a,c,b

Description : Show that the percentage error in the measurement of resistance by a metre bridge is minimum when the null point is near about the centre of the wire.

Last Answer : Show that the percentage error in the measurement of resistance by a metre bridge is minimum when the null point is ... B. 50 cm C. 80 cm D. 100 cm

Description : In a galvanometer, the deflection becomes one half when the galvanometer is shunted by a 20 ohm resistor. The galvanometer resistance is 

Last Answer : In a galvanometer, the deflection becomes one half when the galvanometer is shunted by a 20 ohm resistor. The galvanometer resistance is 10 Ohm

Last Answer : One international ohm is equal to 1.00049 absolute ohm.

Description : at the terminal of a three-phase 6.6Kv alternator a load R=200 ohm is connected between two-phase and the third phase is opened. Z1=z2=5 ohm Zo=2 find out the fault current .

Last Answer : 32A

Description : Four resistances are connected in a circuit in the given figure. The electric cirrent flowing through `4 ohm` and `6 ohm` resistance is respectively

Last Answer : Four resistances are connected in a circuit in the given figure. The electric cirrent flowing through `4 ohm` and `6 ... 1 A and 1 A D. 2 A and 2 A

Description : what is equivalent resistance when four 4 Ohm resistors are connected in i) series ii) parallel

Last Answer : equivalent resistance

Description : Your company receives internet access through a network or a gateway server. Which of the following devices is best suited to protect resources and subnet your LAN directly on the network server? 1) DSL modem 2) A multi-homed firewall 3) VLAN 4) A brouter that acts both as a bridge and a router

Last Answer : 2) A multi-homed firewall

Description : Which of the following stone is best suited for construction of piers and abutments of a railway bridge? (A) Granite (B) Sand stone (C) Lime stone (D) Quartze

Last Answer : Answer: Option A