The torque produced in wattmeter is proportional to

The torque produced in wattmeter is proportional to
by

2 Answers

Answer :

The torque produced in wattmeter is proportional to the r.m.s. value of currents in the two coils

by

Answer :

A
by

Related questions

In a 3-phase power measurement by two wattmeter method the reading of one of the wattmeter was zero...

Description : In a 3-phase power measurement by two wattmeter method the reading of one of the wattmeter was zero. The power factor of the load must be?

Last Answer : In a 3-phase power measurement by two wattmeter method the reading of one of the wattmeter was zero. The power factor of the load must be 0.5.

In a 3-phase power measurement by two wattmeter method, both the wattmeters had identical readings...

Description : In a 3-phase power measurement by two wattmeter method, both the watt meters had identical readings. The power factor of the load was?

Last Answer : In a 3-phase power measurement by two wattmeter method, both the watt meters had identical readings. The power factor of the load was unity.

In a low power factor wattmeter the compensating coil is connected?

Last Answer : In a low power factor wattmeter the compensating coil is connected in series with pressure coil.

In a low power factor wattmeter the pressure coil is connected?

Last Answer : In a low power factor wattmeter the pressure coil is connected to the load side of the current coil.

The pressure coil of a wattmeter should be connected on the supply side of the current coil when?

Last Answer : The pressure coil of a wattmeter should be connected on the supply side of the current coil when load impedance is high.

An induction wattmeter can be used for?

Last Answer : An induction wattmeter can be used for A.C. 

A dynamometer wattmeter can be used for?

Last Answer : A dynamometer wattmeter can be used for both D.C. and A.C.

The resistance in the circuit of the moving coil of a dynamometer wattmeter should be?

Last Answer : The resistance in the circuit of the moving coil of a dynamometer wattmeter should be high.

Ideally, the damping torque should be

Description : Ideally, the damping torque should be  (1) Proportional to velocity of the moving system and operating current.  (2) Proportional to the velocity of the moving system but independent of operating ... operating current.  (4) Independent of the velocity of the moving system and operating current.

Last Answer : Ideally, the damping torque should be Proportional to the velocity of the moving system but independent of operating current. 

The meter which does not have any component in it to provide control torque is

Description : The meter which does not have any component in it to provide control torque is (A) Electrodynamometer for current measurement (B) Electrodynamometer for voltage measurement (C) Electrodynamometer for power measurement. (D) Electrodynamometer for power factor measurement.

Last Answer : The meter which does not have any component in it to provide control torque is Electrodynamometer for power factor measurement.

In a meggar controlling torque is provided by?

Last Answer : In a meggar controlling torque is provided by coil.

In a portable instrument, the controlling torque is provided by?

Last Answer : In a portable instrument, the controlling torque is provided by spring.

The armature torque of the D.C. shunt motor is proportional to?

Last Answer : The armature torque of the D.C. shunt motor is proportional to armature current.

Use Voltmeter, ammeter, wattmeter to determine active, reactive and apparent power consumed in given R-L series circuit, draw phasor diagram.

Description : Use Voltmeter, ammeter, wattmeter to determine active, reactive and apparent power consumed in given R-L series circuit, draw phasor diagram.

Last Answer : Practical Significance In the industry environment Electrical Engineering diploma graduate are expected to measure basic parameters like voltage, frequency, time period etc. for R-L series circuits. Therefore ... /varying L. 7. Draw the phasor diagram for each of reading for verification.

State the principle of wattmeter.

Description : State the principle of wattmeter. 

Last Answer : Working Principle of Wattmeter: It consists of two stationary coils, called current coils and one moving coil, called voltage or potential coil. The current coils are connected such that they ... experiences a force and tends to move in the direction as per Fleming's left hand rule. 

Merits of two wattmeter method

Description : Merits of two wattmeter method

Last Answer : Advantages of Two Wattmeter Method for 3-Phase Power Measurement: 1) It is used for balanced as well as unbalanced load. 2) For the star type load, it is not necessary to ... reactive volt-amperes for balanced loads also. 7) The circuit connections are independent of load connection.

State the effects of errors in dynamometer type wattmeter due to i) pc- inductance ii) pc- capacitance iii) mutual inductance iv) Connection.

Description : State the effects of errors in dynamometer type wattmeter due to i) pc- inductance ii) pc- capacitance iii) mutual inductance iv) Connection.

Last Answer : Errors in wattmeter:  i) pc - inductance: Pressure coil inductance causes wattmeter to read more power than actual .  ii) pc-capacitance: The wattmeter reads less power.  iii) ... iv) Connection: In uncompensated wattmeter , the reading of wattmeter includes the powerloss in coils. 

State any four errors that occur in dynamometer type wattmeter

Description : State any four errors that occur in dynamometer type wattmeter

Last Answer : Errors that occur in dynamometer type wattmeter: 1. Errors due to method of connection. 2. Error due to pressure coil inductance. 3. Error due to pressure coil Capacitance. 4. Error due to mutual ... Error due to eddy currents. 7. Temperature error. 8. Error due to vibration of moving system

Compare CC and PC of wattmeter on the basis of:- (i) Connection (ii) Status (iii) Number of turns (iv) Gauge of wire.

Description : Compare CC and PC of wattmeter on the basis of:- (i) Connection (ii) Status (iii) Number of turns (iv) Gauge of wire.

Last Answer : Particulars Current coil (CC) Pressure coil (PC) Connection Connected in series with load Connected in parallel with load Status It is fixed coil in wattmeter It is moving coil in ... number of turns It is having more number of turns Gauge of wire Less More

With neat diagram explain constructional details of dynamometer type wattmeter.

Description : With neat diagram explain constructional details of dynamometer type wattmeter.

Last Answer : Working Principle of Wattmeter: It consists of two stationary coils, called current coils and one moving coil, called voltage or potential coil. The moving coil is mounted on the spindle, in the gap ... experiences a force and tends to move in the direction as per Fleming's left hand rule. 

State any two disadvantages of one wattmeter method of measurement of 3 phase power.

Description : State any two disadvantages of one wattmeter method of measurement of 3 phase power.

Last Answer : State any two disadvantages of one wattmeter method of measurement of 3 phase power. Disadvantages of one wattmeter method:- 1. Only used for balanced load 2. It can not be used for ... connection then neutral point must be available 4. Delta connection must be opened to connect current coil.

State various types of errors in wattmeter.

Description : State various types of errors in wattmeter.

Last Answer : Types of Error in wattmeter: 1. Errors due to method of connection. 2. Error due to pressure coil inductance. 3. Error due to pressure coil Capacitance. 4. Error due to mutual inductance effect. 5. ... . Error due to eddy currents. 7. Temperature error. 8. Error due to vibration of moving system.

Explain construction & working of electrodynamometer type wattmeter.

Description : Explain construction & working of electrodynamometer type wattmeter.

Last Answer : Electrodynamometer Type Wattmeter:  Construction: It essentially consists of the fixed and moving coil. The fixed coil is split into two equal parts which are placed close together and parallel to each other. ... hence these instruments can be used for measurement of A.C. & D.C. power.

List the different errors in wattmeter & explain compensation for it.

Description : List the different errors in wattmeter & explain compensation for it.

Last Answer : Errors in Wattmeter Compensation method Error due to connection method To overcome this error, wattmeters are provided with additional compensating winding which is connected in series with ... due to friction The weight of moving system be reduced to minimum possible.

List one advantage and one disadvantage of one wattmeter method.

Description : List one advantage and one disadvantage of one wattmeter method. 

Last Answer : Advantages:  1) Only one wattmeter is used.  2) Less number of connections.  3) Cost required is less.  Disadvantages:  1) Used only for 3- Φ balanced load and not for ... be accessible for connecting the Pressure coil.  3) Delta connection must be opened to connect current coil. 

The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is

Description : The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is (A) 11% (B) 9% (C) 1.1% (D) 3%

Last Answer : The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is 11%

In a double squirrel cage induction motor, good starting torque is produced as

Description : In a double squirrel cage induction motor, good starting torque is produced as (A) Large current flows through the outer high resistance winding. (B) Large current flows through the inner high ... the outer high resistance winding. (D) Large current flows through the inner low resistance winding.

Last Answer : In a double squirrel cage induction motor, good starting torque is produced as Large current flows through the outer high resistance winding.

The torque produced in induction type relay (shaded pole structure) is?

Last Answer : The torque produced in induction type relay (shaded pole structure) is inversely proportional to the square of the current.

DC motor gross torque example

Description : DC motor gross torque example

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Describe spring control method of producing controlling torque in measuring instrument. Write any two properties required for spring material.

Description : Describe spring control method of producing controlling torque in measuring instrument. Write any two properties required for spring material.

Last Answer : A)Spring control method: As shown in the figure, the inner ends of the both springs are attahced to the spindle, while outer end of upper spring is attached to the lever and outer ... of spring material: 1.Non Magnetic material 2.Low specific resistance 3.Low temperature coefficient of resistance

Name the different torque and their function in measuring instrument.

Description : Name the different torque and their function in measuring instrument.

Last Answer : List of torques in analog instruments:  1. Deflecting torque  2. Controlling / restraining torque.  3. Damping torque.  1. Deflecting torque:  - To create deflection of pointer ... .  - Bring the pointer to standstill quickly.  - To minimize oscillations about final position. 

State the function of controlling torque in electrical measuring instrument.

Description : State the function of controlling torque in electrical measuring instrument.

Last Answer : Function of controlling torque  1. The function is to opposes the deflection force and increases with the increase in the deflection of the moving system, to limit its movement. 2. and brought ... set a position where the two opposing forces i.e. deflection and controlling forces are equal. 

List the different methods to produce damping torque.

Description : List the different methods to produce damping torque.

Last Answer : Methods of providing damping torque in indicating type instruments: 1) Air friction damping. 2) Fluid friction damping. 3) Eddy current damping.

State the function of controlling torque. Write two types of it.

Description : State the function of controlling torque. Write two types of it.

Last Answer : Function of Controlling Torque:  To restrict the motion of pointer / spindle and stop the pointer at the relevant position to get correct reading.  To bring back pointer to zero ... measurement is removed.  Types of Controlling Torque: 1. Spring control method 2.Gravity control method 

Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to

Description : Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be

Last Answer : Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be 25 N -m

Torque angle for the synchronous machine is the angle between

Description : Torque angle for the synchronous machine is the angle between (A) stator magnetic field and rotor magnetic field (B) stator magnetic field and net magnetic field in the air gap (C) rotor magnetic field and net magnetic field in the air gap (D) excitation voltage and impedance voltage drop

Last Answer : Torque angle for the synchronous machine is the angle between rotor magnetic field and net magnetic field in the air gap

The torque developed by any 3-phase induction motor at 0.8 p.u. slip is

Description : The torque developed by any 3-phase induction motor at 0.8 p.u. slip is (A) Full-load torque (B) unstable torque (C) starting torque (D) break down

Last Answer : The torque developed by any 3-phase induction motor at 0.8 p.u. slip is unstable torque

The shaft torque of a d.c. motor is less than its armature ...

Description : The shaft torque of a d.c. motor is less than its armature torque because of .......... losses.

Last Answer : The shaft torque of a d.c. motor is less than its armature torque because of rotational losses.

The maximum torque of d.c. motors is limited by?

Description : The maximum torque of d.c. motors is limited by?

Last Answer : The maximum torque of d.c. motors is limited by commutation.

Torque developed by a D.C. motor depends upon?

Last Answer : Torque developed by a D.C. motor depends upon magnetic field, active length of the conductor, current flow through the conductors, number of conductors, radius of armature.

For constant torque drive which speed control method is preferred ?

Last Answer : For constant torque drive armature voltage control speed control method is preferred.

Buses, trains, trolleys, hoists, cranes require high starting torque and therefore make use of?

Last Answer : Buses, trains, trolleys, hoists, cranes require high starting torque and therefore make use of D.C. series motor.

For the same H.P. rating and full load speed, following motor has poor starting torque?

Last Answer : For the same H.P. rating and full load speed, following motor has poor starting torque differentially compounded.

The ratio of starting torque to full-load torque is least in case of?

Last Answer : The ratio of starting torque to full-load torque is least in case of shunt motors.

Speed torque characteristic of a repulsion induction motor is similar to that of a D.C.?

Last Answer : Speed torque characteristic of a repulsion induction motor is similar to that of a D.C. compound motor.

In repulsion motor, maximum torque is developed when?

Last Answer : In repulsion motor, maximum torque is developed when brush axis is at 45° electrical to the field axis.

A synchronous motor can develop synchronous torque?

Last Answer : A synchronous motor can develop synchronous torque at synchronous speed.

The maximum constant load torque under which a synchronous motor will pull into synchronism...

Description : The maximum constant load torque under which a synchronous motor will pull into synchronism at rated rotor supply voltage and frequency is known as?

Last Answer : The maximum constant load torque under which a synchronous motor will pull into synchronism at rated rotor supply voltage and frequency is known as pull-in torque.

What is the maximum value of torque angle in synchronous motor?

Description : What is the maximum value of torque angle in synchronous motor?

Last Answer : The maximum value of torque angle in synchronous motor is 90 degrees electrical.

Why a dc series motor has a high starting torque?

Description : Why a dc series motor has a high starting torque?

Last Answer : motor