The main purpose of using core in a transformer is to

The main purpose of using core in a transformer is to

(A) decrease iron losses

(B) eliminate magnetic hysteresis

(C) reduce reluctance of the common magnetic circuit

(D) prevent eddy current loss
by

2 Answers

Answer :

The main purpose of using core in a transformer is to reduce reluctance of the common magnetic circuit

by

Answer :

Reduce Relucatnce of the common magnetic circuit.
by

Related questions

Why does the core of a transformer need to be laminated?

Description : Why does the core of a transformer need to be laminated?

Last Answer : Transformer cores are laminated to reduce eddy current loss.

why the Transformer core is laminated?

Last Answer : Transformer core is laminated to reduce Eddy current losses.

State any four characteristics of core type transformer.

Description : State any four characteristics of core type transformer.

Last Answer : Characteristics of core type transformer: i) It has one window. ii) It has one magnetic circuit. iii) Core surrounds the winding. iv) Average length of core is more. v) Area of cross ... Better cooling for winding. vii) Mechnical strength is comparatively less. viii) Repair and maintenance is easy.

A 40 kVA transformer has a core loss of 400 W and a full load copper loss of 800 W. The

Description : A 40 kVA transformer has a core loss of 400 W and a full load copper loss of 800 W. The proportion of full load at maximum efficiency is

Last Answer : A 40 kVA transformer has a core loss of 400 W and a full load copper loss of 800 W. The proportion of full load at maximum efficiency is 0.707

The core construction is like spokes of a wheel in following transformer:

Description : The core construction is like spokes of a wheel in following transformer:  (A) Berry Type Transformer (B) Core Type Transformer (C) Shell Type Transformer (D) None of the above

Last Answer : The core construction is like spokes of a wheel in following transformer:  Berry Type Transformer

The desirable properties of transformer core material are

Description : The desirable properties of transformer core material are  (1) low permeability and low hysteresis loss. (2) high permeability and high hysteresis loss. (3) high permeability and low hysteresis loss. (4) low permeability and hysteresis loss.

Last Answer : The desirable properties of transformer core material are high permeability and low hysteresis loss.

Material used for construction of transformer core is usually?

Last Answer : Material used for construction of transformer core is usually silicon steel.

When secondary of a current transformer is open-circuited its iron core will be?

Description : When secondary of a current transformer is open-circuited its iron core will be?

Last Answer : When secondary of a current transformer is open-circuited its iron core will be hot because of heavy iron losses taking place in it due to high flux density.

The size of a transformer core will depend on?

Description : The size of a transformer core will depend on?

Last Answer : The size of a transformer core will depend on frequency and area of the core.

Reduction in core losses and increase in permeability are obtained with transformer employing?

Description : Reduction in core losses and increase in permeability are obtained with transformer employing?

Last Answer : Reduction in core losses and increase in permeability are obtained with transformer employing core built-up of laminations of cold rolled grain oriented steel.

State the material used for making (1) Magnetic Core (2) Fuse element

Description : State the material used for making (1) Magnetic Core (2) Fuse element  

Last Answer : The material used for making of:  (1) Magnetic Core : Iron, cobalt, Nickel, CRGO, HRGO , silicon steel  (2) Fuse Element: Tin- lead wire, Tinned copper wire 

Core type transformers are popular in___________.

Description : Core type transformers are popular in___________.  (A) High voltage applications (B) Low voltage applications (C) All of the above (D) None of the above

Last Answer : Core type transformers are popular in High voltage applications

A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum

Description : A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is (A) 28.2 mm (B) 26.4 mm (C) 24.4 mm (D) 22.0 mm

Last Answer : A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is 22.0 mm

A ferrite core has less eddy current loss than an iron core because?

Description : A ferrite core has less eddy current loss than an iron core because?

Last Answer : A ferrite core has less eddy current loss than an iron core because ferrites have high hysteresis.

A single core lead sheathed cable with two dielectrics of permittivity 4 and 3, respectively, are subjected to

Description : A single core lead sheathed cable with two dielectrics of permittivity 4 and 3, respectively, are subjected to same maximum stress. If the conductor diameter is 1.5 cm, the outer diameter of the first dielectric is (A) 1.125 cm (B) 1.5 cm (C ) 2 cm (D) 8 cm

Last Answer : A single core lead sheathed cable with two dielectrics of permittivity 4 and 3, respectively, are subjected to same maximum stress. If the conductor diameter is 1.5 cm, the outer diameter of the first dielectric is 2 cm 

The armature core of a D.C. generator is usually made of?

Last Answer : The armature core of a D.C. generator is usually made of silicon steel.

When a conductor carries more current on the surface as compared to core, it is due to?

Last Answer : When a conductor carries more current on the surface as compared to core, it is due to skin effect.

In DC generators lamination core are generally made of?

Description : In DC generators lamination core are generally made of?

Last Answer : In DC generators lamination core are generally made of silicon steel.

What is the purpose of laminating the core in a transformer?

Description : What is the purpose of laminating the core in a transformer?

Last Answer : In order to minimize eddy current loss.

43 The purpose of providing an iron core in a transformer is to A.Provide support to windings B. Reduce hysteresis loss C. decrease the reluctance of the magnetic path D. reduce eddy current losses

Description : 43 The purpose of providing an iron core in a transformer is to A.Provide support to windings B. Reduce hysteresis loss C. decrease the reluctance of the magnetic path D. reduce eddy current losses

Last Answer : C. Decrease the reluctance of the magnetic path

The purpose of providing an iron core in a transformer is to?

Last Answer : The purpose of providing an iron core in a transformer is to decrease the reluctance of the magnetic path.

The purpose of providing iron core in a step-up transformer is?

Last Answer : The purpose of providing iron core in a step-up transformer is to decrease the magnitude of magnetizing current.

10] The main reason for generation of harmonics in a transformer could be A. Fluctuating load B. Poor insulation C. Mechanical vibrations D. Saturation of core

Description : 10] The main reason for generation of harmonics in a transformer could be A. Fluctuating load B. Poor insulation C. Mechanical vibrations D. Saturation of core

Last Answer : D) saturation of core

What type of processor does the alienware m15x have?

Description : What type of processor does the alienware m15x have?

Last Answer : http://www.laptopmag.com/review/laptops/alienware-m15x.aspx?mode=specs

The area of the yoke in a transformer is taken 15 to 20% larger than that of the core. Why?

Description : The area of the yoke in a transformer is taken 15 to 20% larger than that of the core. Why?

Last Answer : By keeping yoke area 15-20% higher ,the flux density in the yoke is reduced, resulting into reduction in iron losses for yoke. The reduced core area results working flux density and needed to increase the number of turns.

Where is core type and shell type construction suitable for a transformer?

Description : Where is core type and shell type construction suitable for a transformer?

Last Answer : Core type transformers are popular in High voltage applications like Distribution transformers, Power transformers, and obviously auto transformers. Where as, Shell type transformers are ... voltage applications like transformers used in electronic circuits and power electronic converters etc

What are the advantages of shell type transformer over core type transformers?

Description : What are the advantages of shell type transformer over core type transformers?

Last Answer : In shell type transformers the coils are well supported on the all sides and so they can withstand higher mechanical stresses developed during short circuit conditions. Also the leakage reactance will be less in shell type transformers.

72 Harmonics in transformer result in A. Increased core losses B. Increased I2R losses C. Magnetic interference with communication circuits D. All of the above

Description : 72 Harmonics in transformer result in A. Increased core losses B. Increased I2R losses C. Magnetic interference with communication circuits D. All of the above

Last Answer : D. All of the above

[53] The iron loss of the transformer is negligible during short circuit test because A. The entire input is just sufficient to meet Cu losses only B. Flux produced is a small fraction of the normal flux C. Iron core becomes fully saturated D. Supply frequency is held constant

Description : [53] The iron loss of the transformer is negligible during short circuit test because A. The entire input is just sufficient to meet Cu losses only B. Flux produced is a small fraction of the normal flux C. Iron core becomes fully saturated D. Supply frequency is held constant

Last Answer : B. Flux produced is a small fraction of the normal flux

49 The open circuit test is carried out in a transformer to find the A. Cu loss B. Core loss C. Total loss D. Insulation resistance

Description : 49 The open circuit test is carried out in a transformer to find the A. Cu loss B. Core loss C. Total loss D. Insulation resistance

Last Answer : B. Core loss

46 The core used in high frequency transformer is usually A. Copper core B. Cost iron core C. Air core D.Mid steel core

Description : 46 The core used in high frequency transformer is usually A. Copper core B. Cost iron core C. Air core D.Mid steel core

Last Answer : C. Air core

45 The function of conservator in a transformer is A. To protect against internal fault B. To reduce copper as well as core losses C. To cool the transformer oil D. To take care of the expansion and contraction of transformer oil due to variation of temperature of surroundings

Description : 45 The function of conservator in a transformer is A. To protect against internal fault B. To reduce copper as well as core losses C. To cool the transformer oil D. To take care of the expansion and contraction of transformer oil due to variation of temperature of surroundings

Last Answer : D. To take care of the expansion and contraction of transformer oil due to variation of temperature of surroundings

27] In a transformer, the leakage flux of each winding is proportional to the current in that winding because A. Ohm's law applies to magnetic circuits B. Leakage paths do no saturate C. the two windings are electrically isolated D. mutual flux is confined to the core

Description : 27] In a transformer, the leakage flux of each winding is proportional to the current in that winding because A. Ohm's law applies to magnetic circuits B. Leakage paths do no saturate C. the two windings are electrically isolated D. mutual flux is confined to the core

Last Answer : B. Leakage path do not saturate

19 .Transformer cores are built up from laminations rather than from solid metal so that A. Oil penetrates the core more easily B. Eddy current loss is reduced C. Less lamination is required for the windings D. Turn ratio is higher than voltage ratio

Description : 19 Transformer cores are built up from laminations rather than from solid metal so that A. Oil penetrates the core more easily B. Eddy current loss is reduced C. Less lamination is required for the windings D. Turn ratio is higher than voltage ratio

Last Answer : B. Eddy current loss is reduced

8 The transformer core is laminated to A. Reduce the copper losses B. Reduce the core losses C. Reduce the eddy current losses D. None of the above

Description : 8 The transformer core is laminated to A. Reduce the copper losses B. Reduce the core losses C. Reduce the eddy current losses D. None of the above

Last Answer : C. Reduce the eddy current losses

I13) In an ideal transformer A. windings have no resistance B. core has no losses C. core has infinite permeability D. all of the above

Description : 13) In an ideal transformer A. windings have no resistance B. core has no losses C. core has infinite permeability D. all of the above

Last Answer : D. All of the above

12] Which is not the basic element of the transformer? A. core B. primary winding C. secondary winding D. mutual flux

Description : 12] Which is not the basic element of the transformer? A. core B. primary winding C. secondary winding D. mutual flux

Last Answer : D. Mutual flux

Which of the following properties is not necessarily desirable in the material for transformer core? A. Mechanical strength B. Low hysteresis loss C. High thermal conductivity D. High permeability

Description : Which of the following properties is not necessarily desirable in the material for transformer core? A. Mechanical strength B. Low hysteresis loss C. High thermal conductivity D. High permeability

Last Answer : C) high thermal conductivity

Material used for construction of transformer core is usually A. 0.4mm to 0.5 mm B. 4mm to 5 mm C. 14mm to 15 mm D. 25mm to 40 mm

Description : Material used for construction of transformer core is usually A. 0.4mm to 0.5 mm B. 4mm to 5 mm C. 14mm to 15 mm D. 25mm to 40 mm

Last Answer : d) 25mm to 40mm

The core used in high frequency transformer is usually?

Last Answer : The core used in high frequency transformer is usually air core .

State the advantages of instrument transformer in using for extension of range of meters.

Description : State the advantages of instrument transformer in using for extension of range of meters. 

Last Answer : Advantages of instrument transformer: 1. Extension of instrument range is possible. 2. Isolation of instruments from high voltage side. 3. Power loss is less as compared to shunts and multipliers. 4 ... measurement. 5. It is economical method of range extension. 6. Increases in safety of operator.

What is the purpose of providing Taps in transformer and where these are provided?

Description : What is the purpose of providing Taps in transformer and where these are provided?

Last Answer : In order to attain the required voltage, taps are provided, normally at high voltages side(low current).

7 The main advantage of auto transformer over a two winding transformer is A. Hysteresis losses are reduced B. Saving in winding material C. Copper losses are negligible D. Eddy losses are totally eliminated

Description : 7 The main advantage of auto transformer over a two winding transformer is A. Hysteresis losses are reduced B. Saving in winding material C. Copper losses are negligible D. Eddy losses are totally eliminated

Last Answer : A) hysteresis losses is reduced

The main reason for generation of harmonics in a transformer could be?

Last Answer : The main reason for generation of harmonics in a transformer could be saturation of core.

What is the back E.M.F in Transformer ?

Description : What is the back E.M.F in Transformer ?

Last Answer : Back emf in transformer is when apply voltage in primary side of transformer. This voltage produce flux according to Faraday law electro magnetic induction. This flux called mutual flux and this ... secondary flux oppos the applied voltage according to lenz law. its called back emf of transformer

transformer coupled amplifier

Description :  transformer coupled amplifier

Last Answer :  transformer coupled amplifier

Transformer efficiency

Description : Transformer efficiency

Last Answer : Transformer efficiency

Give any three features and any two applications of welding transformer.

Description : Give Any Three Features And Any Two Applications Of Welding Transformer.

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Explain construction and working of isolation transformer.

Description : Explain construction and working of isolation transformer.

Last Answer :  Isolation Transformer https://youtu.be/gq9kjLlhPN0

Write selection criteria of distribution transformer with any four points.

Description : Write selection criteria of distribution transformer with any four points.

Last Answer : Selection Criteria for Distribution Transformer:  i) Ratings - The kVA ratings should comply with IS:2026 ( Part l )-1977*. The noload secondary voltage should be 433 volts for transformers to be ... is not necessary. vi) Cooling - The transformers covered in this group are generally ONAN, AN