A switch tail ring counter is made by using a single D-FF. The resulting circuit is

A switch tail ring counter is made by using a single D-FF. The resulting circuit is

(A) T-FF (B) D-FF (C) SR-FF (D) JK-FF
by

1 Answer

Answer :

A switch tail ring counter is made by using a single D-FF. The resulting circuit is T-FF

by

Related questions

In a single phase motor the centrifugal switch?

Last Answer : In a single phase motor the centrifugal switch disconnects auxiliary winding of the motor.

Source transformation Replace the circuit with voltage source in series with a single resistor

Description : Source transformation Replace the circuit with voltage source in series with a single resistor

Last Answer : Source transformation Replace the circuit with voltage source in series with a single resistor

Starting winding of a single phase motor of a refrigerator is disconnected from the circuit by means of a?

Last Answer : Starting winding of a single phase motor of a refrigerator is disconnected from the circuit by means of a magnetic relay.

How to Replace Tail Lights ?

Description : How to Replace Tail Lights ?

Last Answer : How to Replace Tail Lights Driving with a broken and malfunctioning tail light is illegal, not to mention dangerous. A large number or road accidents happen because of this, which is ridiculous, because changing ... helping you avoid accidents on the road. Follow these steps, and you'll be all set.

How to Cook Lobster Tail ?

Description : How to Cook Lobster Tail ?

Last Answer : How to Cook Lobster Tail Do you know that lobsters were once a food eaten by people that belong to a lower class, and not by aristocrats? Eventually, this delicious delicacy found its way into the ... you want. Remove the tails from the grill and served hot with mayonnaise, melted butter or lemon.

State the function of following elements: i) Storage reservoir ii) Intake iii) Trash rack iv) Tail race.

Description : State the function of following elements: i) Storage reservoir ii) Intake iii) Trash rack iv) Tail race.

Last Answer : i) Function of Storage reservoir:- Its function is to store the water during rainy season and supplies the same throughout the year. ii) Function of Intake:-  The water from reservoir is released ... . OR Tailrace path of water is connected to the next stage of generation/river/lake/ ocean.

What Is Program Counter?

Description : What Is Program Counter?

Last Answer : Answer :Program counter holds the address of either the first byte of the next instruction to be fetched for execution or the address of the next byte of a multi byte instruction, which has ... one as the instruction bytes get fetched. Also Program register keeps the address of the next instruction.

How To Make Stitch Counter Bracelets

Description : How To Make Stitch Counter Bracelets

Last Answer : How To Make Stitch Counter Bracelets Introduction Today, many women feel that their outfits are incomplete unless they also wear an eye-catching bracelet. Bracelets remain one of the most popular ... For stitching projects that have additional rows, simply reset the bracelet and start counting anew.

What is modulus of counter? Show the method to determine the no. of flip flops for a mod-52 counter.

Description : What is modulus of counter? Show the method to determine the no. of flip flops for a mod-52 counter.

Last Answer : Modulus of a counter is the no. of different states through which the counter progress during its operation. It indicates the no. of states in the counter; pulses to be counted are applied to counter. The ... to its starting state after counting N pluses in the case of modulus N counter.

Compare synchronous and asynchronous counter.

Description : Compare synchronous and asynchronous counter.

Last Answer : Asynchronous Counter Synchronous Counter In an Asynchronous Counter the output of one Flip Flop acts as the clock Input of the next Flip Flop. In a Synchronous Counter all the Flip Flop's are ... Also called as serial counter Also called as Parallel Counter

A 3 -stage ripple counter has Flip Flop with propagation delay of 25 nsec and pulse width of strobe input 10

Description : A 3 -stage ripple counter has Flip Flop with propagation delay of 25 nsec and pulse width of strobe input 10 nsec. Then the maximum operating frequency at which counter operates reliably is

Last Answer : A 3 -stage ripple counter has Flip Flop with propagation delay of 25 nsec and pulse width of strobe input 10 nsec. Then the maximum operating frequency at which counter operates reliably is 12.67 MHz

The counter e.m.f. of a d.c. motor?

Description : The counter e.m.f. of a d.c. motor?

Last Answer : The counter e.m.f. of a d.c. motor helps in energy conversion.

What is the difference between a counter and a timer?

Description : What is the difference between a counter and a timer?

Last Answer : Counter counts only when the trigger is applied and timer counts continuously with some equal delay.

Electronic Counter

Description : Electronic Counter

Last Answer : Electronic Counter Electronic counter counts the number of pulses in a given time. Electronic counter is made from cascade flip-flops. It is use to store or display counting. Some counter is use ... BCD counter counts from 0000 (0) to 1001 (9). Johnson counter is the twisted ring counter.

Which attribute would use want a ring of special power to have?

Description : Which attribute would use want a ring of special power to have?

Last Answer : Invisibility, for sure. So many ways to have fun with that ability.

How to Build a Wrestling Ring

Description : How to Build a Wrestling Ring

Last Answer : How to Build a Wrestling Ring The big matches are thrilling for all wrestling fans. Bodies fly across the ring landing cross body on another with a thud and a bounce. What could be more fun than trying out ... with a bit less bounce will mean more pain when compared to a mat with a lot of bounce.

How to Design an Engagement Ring ?

Description : How to Design an Engagement Ring ?

Last Answer : How to Design an Engagement Ring An engagement is a special affair encompassed by a tiny significant symbol - the engagement ring. The engagement ring has a unique design, composed of markings and ... up at the jewelry shop then get ready for the more daunting task of planning a proposal.

How to Determine Ring Size ?

Description : How to Determine Ring Size ?

Last Answer : How to Determine Ring Size Determining a ring size is an important step in choosing a ring, whether for yourself or for someone else. Here are the ways to find the best ring size to fit your finger ... the rings of your mother or sisters for a good feel of what the perfectly-fitted ring feels like.

How to Make Pop Can Ring Snowflakes ?

Description : How to Make Pop Can Ring Snowflakes ?

Last Answer : Pop can rings, normally recycled to create useful objects like wheelchairs and other metal works, can be used to make an ornament enjoyed by people of all ages - the pop can ring snowflake. Tiny ... connections are secure within the pattern. Hang the snowflake via thumbtacks or a string and a hook.

The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted

Description : The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted into rotor to get maximum torque at starting should be

Last Answer : The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted into rotor to get maximum torque at starting should be 0.5 Ohm

The purpose of guard ring in transmission lines is to

Description : The purpose of guard ring in transmission lines is to  (1) reduce the earth capacitance of the lowest unit. (2) increase the earth capacitance of the lowest unit. (3) reduce the transmission lines losses. (4) reduce the reactance of the line

Last Answer : The purpose of guard ring in transmission lines is to reduce the earth capacitance of the lowest unit.

Number of tappings for each equilizer ring is equal to?

Last Answer : Number of tappings for each equilizer ring is equal to number of pole pairs.

Draw & explain touch plate switch using IC555.

Description : Draw & explain touch plate switch using IC555.

Last Answer : It is construct form monostable multivibrator , when metal plates touch by finger then voltage at pin number 2 goes to below 1/3 Vcc then output of lower comparator becomes high hence flip flop set and ... then output of timer goes low and it low till up to the metal plates touch by finger .

If the centrifugal switch of a two-value capacitor motor using two capacitors fails to open then?

Last Answer : If the centrifugal switch of a two-value capacitor motor using two capacitors fails to open then Electrolytic capacitor will, in all probability, suffer break down.

Should I switch to a credit union?

Description : Should I switch to a credit union?

Last Answer : I switched from a bank to a credit union a long time ago. Competitive interest rates, fewer fees, easier loan approvals, better customer service.

How to Replace a Light Switch

Description : How to Replace a Light Switch

Last Answer : How to Replace a Light Switch They say it only takes one idiot to change a light bulb, but to change a light switch requires the skill and carefulness of a handyman. If you have a malfunctioning or a ... doesn't have to be a hassle. Just remember these steps and switching a new switch will be easy.

How to Install a Timer Switch

Description : How to Install a Timer Switch

Last Answer : How to Install a Timer Switch A timer switch is a handy device that automatically turns off a switch after a fixed period of time. This is particularly useful when you have kids at home ... safety precautions when installing switches or anything that might put you in the direct path of electricity.

How To Install A Dimmer Switch

Description : How To Install A Dimmer Switch

Last Answer : How To Install A Dimmer Switch Having a room with a bright light is good, but there are instances when you need the lights to be lower than what you're accustomed. You need to have a dimmer switch, ... your home. Follow them properly, and you'll be able to fiddle with the light levels in your home.

How to Wire a Three-Way Switch ?

Description : How to Wire a Three-Way Switch ?

Last Answer : How to Wire a Three-Way Switch A three-way switch is the most common system installed in residential areas. This system is used to control a light and receptacle or more from two different switches ... wires for interior use. #14 wires are suggested to be used for protected circuits at 15 amperes.

Give the function of fuse and switch.

Description : Give the function of fuse and switch.

Last Answer : Functions of fuse:  * To break the circuit under fault condition.  * To provide overcurrent protection to the circuit.  * To provide short circuit protection to the circuit.  * To provide ...  * To make the electric circuit manually.  * To break the electric circuit manually.

State the function of : i) MCCB ii) ELCB iii) MCB iv) Switch.

Description : State the function of : i) MCCB ii) ELCB iii) MCB iv) Switch. 

Last Answer : i) MCB: Provide short circuit protection & over load protection to electrical loads.  ii) ELCB: Provides protection by detecting the unsafe magnitudes leakage currents flowing to earth and disconnecting ... rating.  iv) Switch: Make and break the electrical connection to the load manually.

Transfer switch

Description : Transfer switch

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

How rating of main switch and cable is selected for Industrial Installation.

Description : How rating of main switch and cable is selected for Industrial Installation.

Last Answer : 1. Rating of Main Switch or Fuse Rating is decided in industrial installation: Rating of main switch or fuse is based up the starting current of motor. For calculating starting current is considered 2 ... take 1.5 times the rated current or full load current. & thus cable rating is decided.

Earthing switch is used for?

Description : Earthing switch is used for?  (A) Measuring of safety voltage (B) Protection of equipment from ground faults (C) Discharging residual energies (D) All of the above 

Last Answer : Earthing switch is used for?  (A) Measuring of safety voltage (B) Protection of equipment from ground faults (C) Discharging residual energies (D) All of the above 

The device which allows reverse power flow and withstands highest switch frequency is

Description : The device which allows reverse power flow and withstands highest switch frequency is (A) GTO (B) MOSFET (C) IGBT (D) Inverter grade SCR

Last Answer : The device which allows reverse power flow and withstands highest switch frequency is MOSFET

A closed switch has a resistance of?

Description : A closed switch has a resistance of?

Last Answer : A closed switch has a resistance of zero.

The switch board instruments?

Last Answer : The switch board instruments should be mounted in vertical position.

Centrifugal switch disconnects the auxiliary winding of the motor at about what percent of synchronous speed?

Last Answer : Centrifugal switch disconnects the auxiliary winding of the motor at about 70 to 80 percent of synchronous speed.

A centrifugal switch is used to disconnect starting winding when motor has?

Last Answer : A centrifugal switch is used to disconnect starting winding when motor has picked up about 50 to 70 per cent of rated speed.

A thermal protection switch can protect against?

Last Answer : A thermal protection switch can protect against overload.

Is thyristor a DC switch?

Last Answer : Yes ,it is one of the main advantage using thristors as a  switch in DC  circuit ,it has a high current gain

Is SCR unidirectional switch?

Last Answer : Yes, SCR is a unidirectional switch.

What are the desirable characteristics of ideal switch?

Description : What are the desirable characteristics of ideal switch?

Last Answer : Desirable characteristics of the ideal switch: It is desirable to have power switches characteristics closer to ideal switch. The ideal switch should have the following characteristics. Zero resistance when ... . 100% efficiency. Able to control power flow with zero power dissipation.

What is the difference between a switch and a relay?

Description : What is the difference between a switch and a relay?

Last Answer : Switch is simply a mechanical contact mechanism and relay is a electromagnetic switch . Switch can be direct mechanically turn on and off but relay can be operated by energising coil .

in which region BJT act as a switch?

Last Answer : BJT act as switch in saturation and  cutoff region ( ON state in saturation region and OFF state in cut-off region )

why IGBT is preferred as a power switch over both power BJT and MOSFET?

Last Answer : Because it has a higher switching frequency and heat tolerance.

How To Make Chalking Made Easy

Description : How To Make Chalking Made Easy

Last Answer : Chalking Made Easy: Simple Instructions for Scrapbookers and Card Designers Chalking is a quick, inexpensive way to add creativity, color, and character to your scrapbooking layouts and other papercrafts. With a ... to experiment. This is where the artist in you is allowed to come out and play!

How Wool is Made

Description : How Wool is Made

Last Answer : How Wool is Made Wool is the fiber derived from the fleece or the fur of the Caprinae family. This family consists of chamois, goats, serows, sheep and relatives. Wool may is made from ... the final wool fabric. These finishing procedures will determine the warmth, durability and value of the wool.

How Silk is Made

Description : How Silk is Made

Last Answer : How Silk is Made Silk is made from the fine woven filaments of cocoons of silkworms. There are almost 70 species of silk moths. The most famous is the Bombyx mori. The caterpillar is among ... of each filament, the way each filament is looped and twisted into the silk thread are also considere

How Paper is Made

Description : How Paper is Made

Last Answer : How Paper is Made Paper is an essential commodity utilized for business and education. Paper is typically made from plant fibres. Most common would be from the fibres of trees. Other materials such as ... done to sift all the unneeded particles of the wood. The cellulose fibres will remain intact.