The time period of third harmonic of power supply frequency, in milliseconds, is

The time period of third harmonic of power supply frequency, in milliseconds, is

(A) 20 (B) 3.33

(C) 6.66 (D) 60
by

1 Answer

Answer :

The time period of third harmonic of power supply frequency, in milliseconds, is 6.66 

by

Related questions

Define: 1) frequency, 2) cycle, 3) time period, 4) amplitude

Description : Define: 1) frequency, 2) cycle, 3) time period, 4) amplitude

Last Answer : 1) frequency: The total number of cycles completed in one second is called frequency. Its unit is cycles per second or Hertz (Hz). Its formula is f = 1/ T, where T is time period. ... is second per cycle. 4) amplitude: the maximum instantaneous value of sine wave is called as amplitude.

For a frequency of 200 Hz, the time period will be?

Description : For a frequency of 200 Hz, the time period will be?

Last Answer : For a frequency of 200 Hz, the time period will be 0.005 s.

Sinusoids find amplitude, period, frequency, voltage (Problem 1)

Description : Sinusoids find amplitude, period, frequency, voltage (Problem 1)

Last Answer : Sinusoids find amplitude, period, frequency, voltage (Problem 1)

The effective resistance of an iron-cored choke working on ordinary supply frequency...

Description : The effective resistance of an iron-cored choke working on ordinary supply frequency is more than its true resistance because of?

Last Answer : The effective resistance of an iron-cored choke working on ordinary supply frequency is more than its true resistance because of iron loss in core.

If the supply frequency to the transformer is increased, the iron loss will?

Last Answer : If the supply frequency to the transformer is increased, the iron loss will increase.

The maximum constant load torque under which a synchronous motor will pull into synchronism...

Description : The maximum constant load torque under which a synchronous motor will pull into synchronism at rated rotor supply voltage and frequency is known as?

Last Answer : The maximum constant load torque under which a synchronous motor will pull into synchronism at rated rotor supply voltage and frequency is known as pull-in torque.

sketch time period measurement by CRO.

Description : sketch time period measurement by CRO.

Last Answer : Horizontal sweep is turned ON and the display appealing on the screen is adjusted by varying different control knobs provided on the front panel of CRO, till the signal is suitably displayed ... Where m=Number of division in one complete cycle n=Setting of time base =Time/Division

In electric traction for a trapezoidal speed-time curve, the time period is

Description : In electric traction for a trapezoidal speed-time curve, the time period is (A) free running speed period = constant speed period (B) free running period = coasting period (C) free running period + coasting period = constant speed period (D) average speed period = scheduled speed period

Last Answer : In electric traction for a trapezoidal speed-time curve, the time period is free running period + coasting period = constant speed period

Draw the block diagram of regulated power supply, explain function of each block and draw waveforms of each stage.

Description : Draw the block diagram of regulated power supply, explain function of each block and draw waveforms of each stage.

Last Answer : 1. A step down transformer 2. A rectifier 3. A filter 4. A regulator Operation of Regulated Power Supply:- Step Down Transformer:- A step down transformer will ... regulator. A regulator will maintain the output constant even when changes at the input or any other changes occur.

What is need of regulated power supply?

Description : What is need of regulated power supply?

Last Answer : A regulated power supply is used to ensure that the output remains constant even if the input changes. But sometimes main supply voltage, load, and surrounding temperature keep changing and altering the ... power supply is needed that will accept an AC input and give a constant DC output.

What is the Power Supply specification for 8085AH microprocessor?

Description : What is the Power Supply specification for 8085AH microprocessor? A) Single +5V supply with 10% voltage margins B) Dual +5V supply with 10% voltage margins C) Single +10V supply with 5% voltage margins D) Dual +5V supply with 5% voltage margins 

Last Answer : What is the Power Supply specification for 8085AH microprocessor? A) Single +5V supply with 10% voltage margins B) Dual +5V supply with 10% voltage margins C) Single +10V supply with 5% voltage margins D) Dual +5V supply with 5% voltage margins 

Two 100W, 200V lamps are connected in series across a 200V supply. The total power

Description : Two 100W, 200V lamps are connected in series across a 200V supply. The total power consumed by each lamp will be in Watts

Last Answer : 4800

Overhead lines for power supply to tramcars are at a minimum height of?

Last Answer : Overhead lines for power supply to tramcars are at a minimum height of 10 m.

The primary reason for low power factor is supply system is due to installation of?

Last Answer : The primary reason for low power factor is supply system is due to installation of induction motors.

For high value of diversity factor, a power station of given installed capacity will be in a position to supply?

Last Answer : For high value of diversity factor, a power station of given installed capacity will be in a position to supply more number of consumers.

why rectifier is used in power supply ?

Last Answer : Rectifier is use in power supply to convert Alternating current (AC) to Direct Current (DC) .

Classify the transformers based on the construction, frequency and power.

Description : Classify the transformers based on the construction, frequency and power.

Last Answer : Classification of Transformer Based On: i) Construction: Shell type, Core type, Berry type ii) Change in voltage level: Step-Up, Step-Down, iii) Number of phases: Single phase, Three phase iv) ... Control vi) Cooling: Self-cooled, Air-cooled, Forced-air cooled, Oil-cooled, Forced-oil cooled. 

What would happen if a power transformer designed for operation on 50 Hz (frequency) were connected to

Description : What would happen if a power transformer designed for operation on 50 Hz (frequency) were connected to a 500 Hz (frequency) source of the same voltage:  (A) Eddy Current and Hysteresis losses will be ... Current will be too much high  (C) Transformer may start to smoke and burn  (D) No effect

Last Answer : What would happen if a power transformer designed for operation on 50 Hz (frequency) were connected to a 500 Hz (frequency) source of the same voltage:  (A) Eddy Current and Hysteresis losses will be ... will be too much high  (C) Transformer may start to smoke and burn  (D) No effect

For a 500 Hz frequency excitation, a 50 km long power line will be modeled as

Description : For a 500 Hz frequency excitation, a 50 km long power line will be modeled as

Last Answer : For a 500 Hz frequency excitation, a 50 km long power line will be modeled as long line

The device which allows reverse power flow and withstands highest switch frequency is

Description : The device which allows reverse power flow and withstands highest switch frequency is (A) GTO (B) MOSFET (C) IGBT (D) Inverter grade SCR

Last Answer : The device which allows reverse power flow and withstands highest switch frequency is MOSFET

The second harmonic distortion is defined as the

Description : The second harmonic distortion is defined as the A) Ratio of amplitude of second harmonic component in the output to that of the fundamental frequency B) Harmonic distortion due to only second harmonic component C) Sum of distortion of first and second harmonic components in the output 

Last Answer : The second harmonic distortion is defined as the Ratio of amplitude of second harmonic component in the output to that of the fundamental frequency

To get minimum harmonic distortion in the output, a 34 to 34 cyclo-converter requires :

Description : To get minimum harmonic distortion in the output, a 3-Ф to 3-Ф cyclo-converter requires :  (A) 12 SCRs (B) 18 SCRs (C) 36 SCRs (D) 72 SCRs

Last Answer : To get minimum harmonic distortion in the output, a 3-Ф to 3-Ф cyclo-converter requires : 36 SCRs

The fractional-pitch used for eliminating 7th harmonic from the emf wave of an alternator is

Description : The fractional-pitch used for eliminating 7th harmonic from the emf wave of an alternator is (A) 2/3 (B) 5/6 (C) 7/8 (D) 6/7

Last Answer : The fractional-pitch used for eliminating 7th harmonic from the emf wave of an alternator is 6/7

Explain the sinusoidal harmonic reduction techniques for cylcoconverters.

Description : Explain the sinusoidal harmonic reduction techniques for cylcoconverters.

Last Answer : sinusoidal

What is the harmonic filter?

Description : What is the harmonic filter?

Last Answer : It is being used to supress the input voltage distortion at input side of any electrical equipment. This distortion is created by other electrical loads like motor, drives etc nearby connected with ... for a range of harmonics or specific harmonics like 3rd harmonics  5th harmonics, 7th harmonics. 

In a series RLC high Q circuit, the current peaks at a frequency

Description : In a series RLC high Q circuit, the current peaks at a frequency  (1) equal to the resonant frequency (2) greater than the resonant frequency (3) less than the resonant frequency (4) equal to half the resonant frequency

Last Answer : In a series RLC high Q circuit, the current peaks at a frequency equal to the resonant frequency

Total instantaneous power supplied by a 3-phase ac supply to a balanced R-L load is

Description : Total instantaneous power supplied by a 3-phase ac supply to a balanced R-L load is

Last Answer : Total instantaneous power supplied by a 3-phase ac supply to a balanced R-L load is constant

What happens to the voltage in the secondary when the frequency of the supply in the primary is decreased?

Description : What happens to the voltage in the secondary when the frequency of the supply in the primary is decreased? A) It increases B) It decreases C) It remains the same D) Cannot say unless the actual percentage increase in the frequency is known

Last Answer : What happens to the voltage in the secondary when the frequency of the supply in the primary is decreased? A) It increases B) It decreases C) It remains the same D) Cannot say unless the actual percentage increase in the frequency is known

With fault clearing time, the transient stability of a power system

Description : With fault clearing time, the transient stability of a power system

Last Answer : With fault clearing time, the transient stability of a power system decreases

At which time power factor of the induction motor is low?

Description : At which time power factor of the induction motor is low?

Last Answer : The power factor of the inducction motor is low at the time of starting as compare to while the induction motor is running.

Reasons as to why you'd be late for your period (besides stress and pregnancy)

Description : Reasons as to why you'd be late for your period (besides stress and pregnancy)

Last Answer : Yes, stress can cause irregularities in cycles.

How to Delay Your Period

Description : How to Delay Your Period

Last Answer : How to Delay Your Period Do you have a vacation or a special occasion where you wish you didn't have to deal with your period? Believe or not, there are some things that you can do to help delay your ... ensure you that you won't have a menstrual period at all. This step isn't for everyone, though.

Define Sample and hold period with reference to S/H circuit.

Description : Define Sample and hold period with reference to S/H circuit.

Last Answer : Sample Period:- The time period during which the voltage across the capacitor is equal to the input voltage is called sample period. Hold Period:- The time period during which the voltage across the capacitor is constant is called hold period.

The period of a wave is?

Last Answer : The period of a wave is time required to complete one cycle.

How To Make An Emergency Supply Kit

Description : How To Make An Emergency Supply Kit

Last Answer : How To Make An Emergency Supply Kit Accidents and natural disasters happen; they are among the unavoidable and unpleasant occurrences that happen in life. Unfortunately, we can't predict when and ... emergency supply kit properly, and you'll be able to make it through the catastrophe unscathed.

Analyze the effect of supply voltage on performance of LED as regards current, Lumen output, efficacy and life.

Description : Analyze the effect of supply voltage on performance of LED as regards current, Lumen output, efficacy and life. 

Last Answer : 1) Effect on Current:- In LED current depends upon supply voltage, if voltage get changes then current also change but this change in current will be control by resistors which are connected in series.  2) ...   4) Effect on Life:- If supply voltage is not stable then life of LED get reduced. 

Define phase sequence of three phase supply with waveforms.

Description : Define phase sequence of three phase supply with waveforms. What is normal phase sequence? Which 3 standard colours are used to denote the phase sequence?

Last Answer : It  is  sunnosoidal  sequence.

An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to

Description :  An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

Last Answer :  An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

A change of 4% in the supply voltage to an induction motor will produce a change of approximately

Description : A change of 4% in the supply voltage to an induction motor will produce a change of approximately

Last Answer : A change of 4% in the supply voltage to an induction motor will produce a change of approximately 8% in the rotor torque

We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance

Description : We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be

Last Answer : We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be 2.4 kOhm

What will happen if the primary of a transformer is connected to D.C. supply?

Description : What will happen if the primary of a transformer is connected to D.C. supply?  (A) Transformer will operate with low efficiency (B) Transformer will operate with high efficiency (C) No effect (D) Transformer may start to smoke and burn 

Last Answer : What will happen if the primary of a transformer is connected to D.C. supply?  (A) Transformer will operate with low efficiency (B) Transformer will operate with high efficiency (C) No effect (D) Transformer may start to smoke and burn 

The supply for arc welding is :

Description : The supply for arc welding is : 

Last Answer : The supply for arc welding is : Low voltage, high current ac or dc voltage

Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch

Description : Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

Last Answer : Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

While keeping the excitation constant, if the steam supply of an alternator running in parallel with another

Description : While keeping the excitation constant, if the steam supply of an alternator running in parallel with another identical alternator is increased, then (A) It would over-run the other alternator (B) Its rotor ... (C) Its portion of share in load will increase (D) Its power factor would be decreased.

Last Answer : While keeping the excitation constant, if the steam supply of an alternator running in parallel with another identical alternator is increased, then Its portion of share in load will increase

In a three-phase supply floating neutral is undesirable because it way give rise to?

Description : In a three-phase supply floating neutral is undesirable because it way give rise to?

Last Answer : In a three-phase supply floating neutral is undesirable because it way give rise to unequal line voltages across the load.

If a D.C. series motor is operated on A.C. supply, it will?

Last Answer : If a D.C. series motor is operated on A.C. supply, it will spark excessively, have poor efficiency, have poor power factor.

A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by...

Description : A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will?

Last Answer : A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will not start at all.

If the synchronous motor, properly synchronised to the supply is running on no load and is having negligible loss then?

Last Answer : If the synchronous motor, properly synchronised to the supply is running on no load and is having negligible loss then the stator current will be zero.

In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of?

Description : In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of?

Last Answer : In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of less than 15A.