The sequence components of current of a single-phase load connected to a 3-phase system are

(A) equal positive and negative sequence components

(B) equal positive, negative and zero sequence components

(C) vector sum of sequence currents is zero

(D) algebraic sum of sequence currents is zero

1 Answer

Answer :

The sequence components of current of a single-phase load connected to a 3-phase system are equal positive, negative and zero sequence components

Related questions

Description : Define phase sequence of three phase supply with waveforms. What is normal phase sequence? Which 3 standard colours are used to denote the phase sequence?

Last Answer : It  is  sunnosoidal  sequence.

Description : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is :

Last Answer : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is : 200 V

Description : If non-linear loads are connected to the power system, then (A) displacement power factor is same as the total power factor (B) displacement power factor is not equal to the total power ... factor is due to harmonic currents (D) total power factor is due to fundamental component of current

Last Answer : If non-linear loads are connected to the power system, then displacement power factor is not equal to the total power factor

Description : Single-phase mid-point controlled rectifier with RL load

Last Answer : Single-phase mid-point controlled rectifier with RL load : The circuit configuration of single-phase midpoint controlled rectifier is shown in the figure. During positive half-cycle of ... some part of next positive half-cycle of voltage with reversed polarity can appear across load.

Description : Single-phase Midpoint controlled rectifier with Resistive load

Last Answer : Single-phase Midpoint controlled rectifier with Resistive load:  1) During positive half cycle of AC supply, a is positive with respect to b , this makes T1 forward biased and T2 is reverse ... voltage reverses the polarity and T2 is turned off. The operation is as shown in waveforms.

Last Answer : 1. Connected Load: It is the sum of load of all equipment's connected to supply system which are in use or not in use of each consumer. OR   The sum of connected load of all consumers ... is the maximum load which a consumer uses at a particular time period out of his total connected load. 

Description : Define the terms: i) Tariff ii) Fuel surcharge iii) Electricity Duty iv) Connected load

Last Answer : i) Tariff: The rate at which a consumer is charged for the consumption of electricity is called as tariff. OR The amount of money framed by the supplier for the supply of electrical energy ... is the total wattage of all appliances which are used by the consumer on his sanctioned connection. 

Description : Define the following terms related to tariff: (i) Connected load (ii) Unit consumed (iii) Fixed charges (iv) Electricity Tax 

Last Answer : (i) Connected load  It is the sum of the power ratings (Watts or kW or MW) of all devices and machines existing (installed) in the premises of consumer. It is used to decide the ... a percentage of the total electricity bill which includes all amounts that go to the electricity supply agency. 

Description : Define each of following terms: i) Connected load ii) Spinning reserve. 

Last Answer : i) Connected Load :- It is the sum of load of all equipment connected to supply system which are in use or not in use of each consumer. ii) Spinning Reserve:- It is reserved generating capacity in operation and connected to bus bar and ready to take a load.

Description : When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is

Last Answer : When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is √3/2

Description : In a single-phase transformer, the magnetizing current is (A) in phase with the no-load current (B) in quadrature with the no-load current (C) the product of no-load current and power factor (D) in phase with the flux in the core

Last Answer : In a single-phase transformer, the magnetizing current is in phase with the flux in the core

Description : List and explain the components of a hydraulic system.

Last Answer : Components Hydraulic: Hydraulic pump- Supply fluid to the components in the system. Pressure in the system develops in reaction to the load. Hence, a pump rated for 5,000 ... mechanical components and need to be removed along with other contaminants.  Seals, fittings and connections.

Description : What are the components of system bus? A) CPU Bus, Address Bus, Data Bus B) Memory, Control Unit, ALU C) Data Bus, Address Bus, Control Bus D) Register, PC, IR

Last Answer : What are the components of system bus? A) CPU Bus, Address Bus, Data Bus B) Memory, Control Unit, ALU C) Data Bus, Address Bus, Control Bus D) Register, PC, IR

Description : What are the main components of a computer system?

Last Answer : CPU,monitor, keyboard and mouse

Description : What are the components of a power system?

Last Answer : generator Traansformer Conductors Insulators

Last Answer : A balanced 3-phase system consists of positive sequence currents.

Description : Generally in a power system network, the load is represented as a :  (A) Constant power in both load flow study and in stability study  (B) Constant power in load flow study and constant ... impedance in load flow study  (D) Constant impedance in both load flow study and in stability study

Last Answer : Generally in a power system network, the load is represented as a : Constant power in load flow study and constant impedance in stability study 

Description : A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms value of the current flowing through each thyristor of the converter is

Last Answer : Please show the solution for this question

Description : A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current requirement is 0.2 A. The minimum voltage at input is 24 V. What is the required value of series resistance with source? A) 5.45 Ω B) 6 Ω C) 7.2 Ω D) 6.38 Ω  

Last Answer : A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current requirement is 0.2 A. The minimum voltage at input is 24 V. What is the required value of series resistance with source? A) 5.45 Ω B) 6 Ω C) 7.2 Ω D) 6.38 Ω  

Description : For a transformer, operating at constant load current, maximum efficiency will occur at?

Last Answer : For a transformer, operating at constant load current, maximum efficiency will occur at unity power factor.

Description : In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of?

Last Answer : In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of less than 15A.

Description : Give the circuit analysis of current source inverter with resistive load. What are the main difference between voltage source inverter and current source inverter?

Last Answer : Current source inverter (CSI): In current source inverter, the output current is independent of load. The input current of current source inverter is constant. Current source converter converts DC input current to ... are connected in parallel. In CSI diodes are connected in series.

Description : The line current in a balanced delta system is 30 A. The load current is (A) 30√3 A (B) 30/√3 A (C) 10 A (D) 30/√2 A

Last Answer : The line current in a balanced delta system is 30 A. The load current is 30/√3 A

Description : What is Phase sequence? Draw waveforms of 3 phase emf.

Last Answer : Phase sequence: It is the order in which the three phases reach their peak or maximum values. It is shown in below fig. the phase sequence is A-B-C (or R-Y-B). In the following waveforms, it is ... 120º, B- phase voltage attains its positive maximum value. So the phase sequence is R-Y-B. 

Description : State the use of:- (i) Clip-on-ammeter (ii) Phase sequence indicator

Last Answer : (i) Clip-on-ammeter: used for measurement of current in cables/lines in live conditions without disconnecting them.  (ii) Phase sequence indicator: To determine /find the phase sequence of 3 phase supply. 

Description : Describe with neat diagram phase sequence indicator.

Last Answer : Phase Sequence Indicator: There are two types of phase sequence indicators: (a) Rotating type phase sequence indicator (b) Static type phase sequence indicator (a) Rotating Type Phase Sequence ... of the supply is reversed or altered, then the lamp 1 will glow brighter than the lamp 2.

Description : State the application of phase sequence indicator; clip on ammeter, frequency meter & P.F. meter.

Last Answer : Phase Sequence Indicator:  1. For finding correct phase sequence of supply  2. For obtaining exact instant of parallel operation of alternators.  3. For obtaining reversal of rotation ...  4. In electroplating industries   5. In various processes industries for measuring power factor

Description : Which of the following is the least expensive protection for over current in low voltage system?  (A) Rewireable fuse (B) Isolator (C) Oil Circuit breaker (D) Air break circuit breaker

Last Answer : Which of the following is the least expensive protection for over current in low voltage system?  (A) Rewireable fuse (B) Isolator (C) Oil Circuit breaker (D) Air break circuit breaker

Description : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) ... proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

Last Answer : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ directly proportional to α and inversely proportional to Φ

Description : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is (A) sinusoidal current (B) constant dc current (C) continuous rectangular pulses (D) alternating rectangular pulses

Last Answer : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is alternating rectangular pulses

Description : Describe different RT level computational and sequential components used to design single function processors.

Last Answer : RT-level combinational components:- To reduce the complexity in digital logic, combinational components are used, which are more powerful than logic gates.  Such combinational ... during a clock edge. An asynchronous inputs value effects the circuit independent of the clock.

Description : A negative sequence relay is used for protection of  (1) Generator (3) Motor (2) Transformer (4) Long Transmission lines

Last Answer : A negative sequence relay is used for protection of Generator 

Description : In an R-C phase shift oscillator, the minimum no. of R-C networks to be connected in cascade will be -

Last Answer : In an R-C phase shift oscillator, the minimum no. of R-C networks to be connected in cascade will be 3

Description : Explain Three Phase Bidirectional Delta Connected Controller.

Last Answer : Three Phase Bidirectional Delta Connected Controller:

Description : Following are the components of jet engine

Last Answer : Following are the components of jet engine: 1. Air intakes 2. Compressors 3. Combustors 4. Turbines 5. Afterburners (reheat) 6. Nozzle 7. Bypass duct 8. Shaft

Description : List the different components used in CD player.

Last Answer : CD mechanism CD pick up assembly Gear system Motors CD lens Display panel Front panel Servo systems.

Description : Describe the process of photo emission. State the application of photo emission in electronic components

Last Answer : Process of Photoemission:when light of appropriate frequency and intensity is incident upon a surface of certain materials,the energy of light is given to electrons to leave the surface of metal ... photo tubes are used in door openers,counters, position and temperature control and colour analysis 

Description : List out main components of Diesel power station. 

Last Answer : Main components of Diesel power station: 1) Diesel Engine 2) Engine Air intake system 3) Engine Fuel System 4) Engine Exhaust system 5) Engine cooling system 6) Engine Lubricating system 7) Engine Starting system 8) Diesel Engine Generator (Alternator) 

Description : List out main components of Reactors. 

Last Answer : List the main components of Reactors:  1. Core 2. Nuclear fuel (U235) 3. Moderator 4. Control Rod 5. Reflector 6. Reactor vessel 7. Shielding  

Description : Which of the following are components of Central Processing Unit (CPU)?  (A) Arithmetic logic unit, Mouse  (B) Arithmetic logic unit, Control unit  (C) Arithmetic logic unit, Integrated Circuits  (D) Control Unit, Monitor

Last Answer : Which of the following are components of Central Processing Unit (CPU)?  (A) Arithmetic logic unit, Mouse  (B) Arithmetic logic unit, Control unit  (C) Arithmetic logic unit, Integrated Circuits  (D) Control Unit, Monitor

Last Answer : Categories of semiconductor components (Integrated circuit families) Integrated circuits are made from semiconductor material These are divided into three main categories A) ... minus, true or false etc. common families include Transistor Transistor Logic (TTL), CMOS, MOSFET.

Description : An additional condition for parallel operation of three-phase transformers over single-phase transformers is that

Last Answer : An additional condition for parallel operation of three-phase transformers over single-phase transformers is that the transformers should belong to the same vector group

Description : In a single-phase induction motor, the operating direction is determined by the ________ A) Rotor B) Stator C) Starting circuit D) None of these

Last Answer : In a single-phase induction motor, the operating direction is determined by the Starting circuit

Description : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is (A) 4.5 V (B) 6.75 V (C) 9 V (D) 13.5 V

Last Answer : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is 9 V

Description : In a single-phase induction motor when the rotor is stationary and voltage is applied to the stator, then (A) the flux is constant (B) the flux first decreases and then increases in ... increases and decreases in the opposite direction with the same magnitude (D) current flows through the rotor

Last Answer : In a single-phase induction motor when the rotor is stationary and voltage is applied to the stator, then the flux first decreases and then increases in the same direction

Description : A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred resistance of 0.2 Ω and reactance of 0.5 Ω. The approximate primary induced emf is (A) 216 V (B) 226 V (C) 234 V (D) 236 V

Last Answer : A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred resistance of 0.2 Ω and reactance of 0.5 Ω. The approximate primary induced emf is 226 V

Last Answer : The starting winding of a single-phase motor is placed in stator.

Last Answer : The capacitors used in single-phase capacitor motors have no polarity marking.

Last Answer : If starting winding of a single-phase induction motor is left in the circuit, it will draw excessive current and overheat.

Last Answer : A single-phase induction motor is inherently non-self-starting with low torque.