In a battery, the difference between the no-load voltage and the measured voltage output is called ________

In a battery, the difference between the no-load voltage and the measured voltage output is called ________

A) Internal voltage B) Internal resistance

C) External resistance D) All the above
by

1 Answer

Answer :

In a battery, the difference between the no-load voltage and the measured voltage output is called Internal resistance

by

Related questions

Analyze the effect of supply voltage on performance of LED as regards current, Lumen output, efficacy and life.

Description : Analyze the effect of supply voltage on performance of LED as regards current, Lumen output, efficacy and life. 

Last Answer : 1) Effect on Current:- In LED current depends upon supply voltage, if voltage get changes then current also change but this change in current will be control by resistors which are connected in series.  2) ...   4) Effect on Life:- If supply voltage is not stable then life of LED get reduced. 

With the help of N-channel JFET describe the effect of input voltage VGS on output current ID.

Description : With the help of N-channel JFET describe the effect of input voltage VGS on output current ID.

Last Answer : Working of N channel FET: * When a voltage is applied between the drain and source with a DC supply (VDD), the electrons flows from source to drain through narrow channel ... where the channel gets completely blocked and the drain current becomes zero is called pinch- off voltage. 

Define: i) Input Offset Voltage ii) Input offset Current iii) Input Bias Current iv) Output offset voltage

Description : Define: i) Input Offset Voltage ii) Input offset Current iii) Input Bias Current iv) Output offset voltage

Last Answer : Definition of parameters of OPAMP is follows:  i) Input Offset Voltage: Input offset voltage is defined as the voltage that must be applied between the two input terminals of an OPAMP to null or ... to ground) and output voltage is obtained non zero such voltage is output offset voltage of opamp.

A linear network has a current input 4cos(ω t + 20º)A and a voltage output 10 cos(ωt +110º) V. Determine the associated impedance.

Description : A linear network has a current input 4cos(ω t + 20º)A and a voltage output 10 cos(ωt +110º) V. Determine the associated impedance.

Last Answer : Solution

The load of a consumer is generally measured in terms of :

Description : The load of a consumer is generally measured in terms of : (A) Volts (B) Amperes (C) Ampere hour (D) kW

Last Answer : The load of a consumer is generally measured in terms of : kW

The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a

Description : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) ... proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

Last Answer : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ directly proportional to α and inversely proportional to Φ

Which motor should not be started on no-load ?

Last Answer : Series motor should not be started on no-load.

A no-load test is performed on a transformer to determine?

Description : A no-load test is performed on a transformer to determine?

Last Answer : A no-load test is performed on a transformer to determine magnetizing current and loss.

The power consumed by a balanced 3-ph load is measured by two-wattmeter method. The meter readings are

Description : The power consumed by a balanced 3-ph load is measured by two-wattmeter method. The meter readings are 8 kW and 4 kW. The power factor of the load is (A) zero (B) 0.5 (C) between zero and 0.5 (D) between 0.5 and unity

Last Answer : The power consumed by a balanced 3-ph load is measured by two-wattmeter method. The meter readings are 8 kW and 4 kW. The power factor of the load is between 0.5 and unity

The largest change of input quantity for which there is no output of instrument is called ______

Description : The largest change of input quantity for which there is no output of instrument is called ______ A) Dead time B) Dead input C) Dead output D) Dead zone

Last Answer : The largest change of input quantity for which there is no output of instrument is called Dead zone

Explain full wave bridged rectifier with the help of circuit diagram and input output waveform.

Description : Explain full wave bridged rectifier with the help of circuit diagram and input output waveform.

Last Answer : 1. In positive half cycle (0 to Π): The end A of the secondary winding becomes positive and end B negative. This makes diode D1 and D4 forward biased while diode D2 and D3 are reverse biased. These two diodes will ... D2 and D3 when it is conducting is as follows.  B - D2 - RL - D3 - A 

How is energy measured ?

Description : How is energy measured ?

Last Answer : How is energy measured What is energy? Energy is the ability to do work and results in a change. It is a very commonly used word in our everyday lives. Different Forms of Energy Energy exists as ... for one hour. Horsepower is another unit of measuring energy. 1 HP is equivalent to 745.7 watts.

True value has been 50 whereas measured value is 40 then the percentage error in the reading

Description : True value has been 50 whereas measured value is 40 then the percentage error in the reading will be ______.  (A) 20% (B) 40% (C) 50% (D) 30%

Last Answer : True value has been 50 whereas measured value is 40 then the percentage error in the reading will be 20%. 

The self inductance of a coil can be measured using

Description : The self inductance of a coil can be measured using (A) Wien’s Bridge (B) Schering Bridge (C) Anderson’s Bridge (D) Wheatstone Bridge

Last Answer : The self inductance of a coil can be measured using Anderson’s Bridge

Liquid flow rate is measured using

Description : Liquid flow rate is measured using (A) a pirani gauge (B) a pyrometer (C) an orifice plate (D) a bourdon tube

Last Answer : Liquid flow rate is measured using an orifice plate

Dielectric loss in a capacitor is best measured by

Description : Dielectric loss in a capacitor is best measured by (A) Wien Bridge (B) Schering Bridge (C) Anderson Bridge (D) Heaviside-Campbell Equal Ratio Bridge

Last Answer : Dielectric loss in a capacitor is best measured by Schering Bridge

E.m.f. of a Weston cell is accurately measured by?

Last Answer : E.m.f. of a Weston cell is accurately measured by electrostatic voltmeter.

A direct current can be measured by?

Last Answer : A direct current can be measured by a D.C. potentiometer in conjunction with a standard resistance.

Resistances can be measured with the help of?

Last Answer : Resistances can be measured with the help of ohmmeters and resistance bridges.

Iron loss of a transformer can be measured by?

Last Answer : Iron loss of a transformer can be measured by low power factor wattmeter.

What Are Input & Output Devices?

Description : What Are Input & Output Devices?

Last Answer : Answer :Keyboards, Floppy disk are the examples of input devices. Printer, LED / LCD display, CRT Monitor are the examples of output devices.

Explain DC coupled drive circuit with unipolar output.

Description : Explain DC coupled drive circuit with unipolar output.

Last Answer : DC coupled drive circuit with unipolar output: The figure shows the circuit and waveforms

what is the difference between capacitor and battery ?

Description : what is the difference between capacitor and battery ?

Last Answer : A capacitor stores power but in very small quantitys and work in D/C and A/C circuits and it needs a power source from wich it gets the power it stores and a battery also stores power but in much larger quantitys measured in Amp/Hours

When the voltage across a battery is measured using a D.C potentiometer, the reading shows 1.08 V. But

Description : When the voltage across a battery is measured using a D.C potentiometer, the reading shows 1.08 V. But when the same voltage is measured using a Permanent Magnet Moving Coil (PMMC) voltmeter, the voltmeter reading shows 0.99 ... resistance of the battery, in Ohm , is (A) 150 (B) 100 (C) 50 (D) 200

Last Answer : When the voltage across a battery is measured using a D.C potentiometer, the reading shows 1.08 V. But when the same voltage is measured using a Permanent Magnet Moving Coil (PMMC) voltmeter, ... resistance of the voltmeter is 1100 Ohm , the internal resistance of the battery, in Ohm , is 100

when charging a battery we use a DC supply but not an AC supply. Why ?

Description : when charging a battery we use a DC supply but not an AC supply. Why ?

Last Answer : When power is supplied to the battery, electrolyte inside the battery is divided into positive and negative ions, where ions with similar pole is gained in one side. This reactionʼs flow coincides with direct current.

List out the precautions to be taken while charging of lead- acid battery

Description : List out the precautions to be taken while charging of lead- acid battery 

Last Answer : precautions to be taken while charging of lead- acid battery: 1) Never keep the battery in the circuit and connect for external charging if it is not designed so. 2) While disconnecting / removing a ... tools etc on batteries. 10) Do not splash any liquids on the batteries, near the charger etc.

Explain the maintenance of lead acid battery.

Description : Explain the maintenance of lead acid battery.

Last Answer : Maintenance of lead acid battery: 1) Keep the container surface dry by using dry cloths. 2) Tighten the terminal connections. 3) Battery should not be discharged below a minimum voltage. 4) Never keep battery ... -container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

In lead acid battery the density of acid indicates the

Description : In lead acid battery the density of acid indicates the  (1) charge of the battery (2) level of acid (3) e.m.f of the battery (4) damage of the plates

Last Answer : In lead acid battery the density of acid indicates the charge of the battery

The current flow in a battery is due to ______

Description : The current flow in a battery is due to ______ A) movement of ions B) movement of protons C) movement of holes D) movement of neutrons

Last Answer : The current flow in a battery is due to movement of ions

Can you make alternating current through a battery?

Description : Can you make alternating current through a battery?

Last Answer : Yes, we can make AC through a battery using an inverter.

Is current from a battery AC or DC?

Description : Is current from a battery AC or DC?

Last Answer : The current from the battery is DC

A 40 W bulb is connected in series with a room heater. If now 40 W bulb is replaced by...

Description : A 40 W bulb is connected in series with a room heater. If now 40 W bulb is replaced by 100 W bulb, the heater output will?

Last Answer : A 40 W bulb is connected in series with a room heater. If now 40 W bulb is replaced by 100 W bulb, the heater output will increase.

How positive and negative terminals of a battery are identified?

Description : How positive and negative terminals of a battery are identified?

Last Answer : Answer: Positive terminal is identified painted with red color and negative terminal is identified painted with blue color on the top of the battery

What is end of life of the battery?

Description : What is end of life of the battery?

Last Answer : Answer: If a battery cannot able to hold proper charge or if the battery capacity is falls below 80% of its rated capacity then it is considered as the end of life of the ... Charging and discharging cycles Temperature Leakage of the gases or electrolyte corrosion of the plates over discharge rates

What is stratification in the battery?

Description : What is stratification in the battery?

Last Answer : Answer: During charging of the battery acid is produced at the plate surface and during discharging of the battery acid will be consumed, due to this nonuniform concentration heavy parts of the ... on the top. This phenomenon is call stratification. Stratification affects the life of the battery.

What factors that decide the VRLA battery to completely charged from fully discharged condition?

Description : What factors that decide the VRLA battery to completely charged from fully discharged condition?

Last Answer : Answer: Some of the important factors that determine the duration of the discharged battery to charge are: Duration of the discharge occurred Temperature at which battery is operating Size and efficiency of the charger

Do temperature have effect on battery?

Description : Do temperature have effect on battery?

Last Answer : Answer: Temperature is one of the major factors that have impact on battery performance, shelf life, charging and battery voltage control. At higher temperature batteries will have more chemical activity compared to batteries which operate at the designed temperature

How can the state of charge of battery is best indicated?

Description : How can the state of charge of battery is best indicated?

Last Answer : Ans. The state of charge of battery is best indicated by specific gravity of electrolyte and voltage.

What is a battery?

Description : What is a battery?

Last Answer : Ans. Battery is a device which converts chemical energy into electrical energy. It stores energy in form of chemical energy. Types a) Primary cell batteries b) Secondary batteries.

Truck Battery

Description : Truck Battery

Last Answer : Need a battery to power your truck but not sure what a truck battery is? Like most batteries used on cars, motorcycles and tractors, truck batteries are lead-acid types. They use lead plates that are ... onto your skin, wash it away immediately with water. Visit a doctor if your skin is burned.

Motorcycle Battery

Description : Motorcycle Battery

Last Answer : A true rider knows his motorcycle battery well. After all, it's the part of the bike that allows the engine to start. A typical 12-volt motorcycle battery is encased in plastic and ... result to permanent damage. Always ask an expert first before topping up or charging your motorcycle battery.

Marine Battery

Description : Marine Battery

Last Answer : It's nice to go fishing or sailing on a warm sunny day but make sure that your boat has the right battery to power it. A good boat runs on a good marine battery. There are two basic types ... switch a deep-cycle with a cranking battery. The proper battery use will ensure a day of smooth sailing.

Lead Acid battery

Description : Lead Acid battery

Last Answer : If you are a car owner, no doubt you have heard of the term lead-acid battery many times. Well, most car, truck, motorcycle and marine batteries are lead-acid batteries. Lead-acid ... for many of their power supply needs. Lead pollution can be lessened by proper disposal of these batteries.

Battery Trays

Description : Battery Trays

Last Answer : You cannot just put a battery in your car, leave it there and drive. That battery might fall over and cause some serious problems to your car. You need a battery tray to secure the battery ... , vibration and shock. High-end models cost more but you will eventually spend less on their maintenance.

Battery Terminal Cleaners

Description : Battery Terminal Cleaners

Last Answer : Corrosion is the enemy of car batteries. It can make the most high-end cars fail to start. Battery terminals are especially prone to corrosion because of the presence of water and acid in their ... be restored. If your battery terminals have too much deposit buildup, replace them with new ones.

Battery Terminal

Description : Battery Terminal

Last Answer : Automotive battery terminals can mean either the posts on a battery to which the jumper cables attach or the part of the cables that attach to the battery's posts. The latter are sometimes ... properly maintained for the car to run smoothly. Regular inspection helps to keep them in good condition.

Battery Clips

Description : Battery Clips

Last Answer : So you have a car battery that is losing its power and you don't want to buy a new one. You can recharge it by using battery chargers. However, how do you connect the charger to your ... are unsure about how these clips fasten to your car's battery, ask experts first to avoid potential accidents.

Battery Charger

Description : Battery Charger

Last Answer : Do you have a car battery that is losing its power? You can use a battery charger to bring its power back. A battery charger is a device that forces electric current through the battery ... battery are compatible. Carefully read the instructions on how to install the charger to avoid any accidents.

How To Make A USB Battery

Description : How To Make A USB Battery

Last Answer : Do you know that you can change a normal 9V battery into a USB one? Here's how. Materials Needed 5.1V zener diode 330-ohm resistor 9V battery connector 9V battery Soldering gun and iron Female USB ... 5-1 step 5-2 Now, you should have your very own USB battery in those times of emergency.

A Battery of Powerful Hacks

Description : A Battery of Powerful Hacks

Last Answer : Chances are that since it's just after the holidays, you've got some nifty new gadgets that need power. If buying batteries is breaking the bank, we're here to help. Here are three of the best battery- ... because fixing these is easy, as long as you know how. Here's how to fix laptop power input.