The largest change of input quantity for which there is no output of instrument is called ______

A) Dead time B) Dead input

C) Dead output D) Dead zone

1 Answer

Answer :

The largest change of input quantity for which there is no output of instrument is called Dead zone

Related questions

Description : Explain full wave bridged rectifier with the help of circuit diagram and input output waveform.

Last Answer : 1. In positive half cycle (0 to Π): The end A of the secondary winding becomes positive and end B negative. This makes diode D1 and D4 forward biased while diode D2 and D3 are reverse biased. These two diodes will ... D2 and D3 when it is conducting is as follows.  B - D2 - RL - D3 - A 

Description : What Are Input & Output Devices?

Last Answer : Answer :Keyboards, Floppy disk are the examples of input devices. Printer, LED / LCD display, CRT Monitor are the examples of output devices.

Description : With the help of N-channel JFET describe the effect of input voltage VGS on output current ID.

Last Answer : Working of N channel FET: * When a voltage is applied between the drain and source with a DC supply (VDD), the electrons flows from source to drain through narrow channel ... where the channel gets completely blocked and the drain current becomes zero is called pinch- off voltage. 

Description : Define: i) Input Offset Voltage ii) Input offset Current iii) Input Bias Current iv) Output offset voltage

Last Answer : Definition of parameters of OPAMP is follows:  i) Input Offset Voltage: Input offset voltage is defined as the voltage that must be applied between the two input terminals of an OPAMP to null or ... to ground) and output voltage is obtained non zero such voltage is output offset voltage of opamp.

Description : A linear network has a current input 4cos(ω t + 20º)A and a voltage output 10 cos(ωt +110º) V. Determine the associated impedance.

Last Answer : Solution

Description : ‘PMMC instrument is not suitable to measure AC quantity’. State the reason.

Last Answer : The direction of force exerted on moving coil depends on the direction of current flowing through moving coil. If the direction of magnetic field is kept constant, it produces unidirectional torque if the current is ... on the coil in one cycle to zero. Hence the meter cannot read A.C. quantities.

Description : An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be

Last Answer : An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be 2 watts

Description : Explain lagging quantity and leading quantity, explain this concept with voltage and current waveform

Last Answer : When two alternating quantities attain their respective zero or peak values simultaneously, the quantities are said to be in-phase quantities. When the quantities do not attain their respective zero or ... current is leading the voltage or the voltage is said to be lagging behind the current.

Description : In a battery, the difference between the no-load voltage and the measured voltage output is called ________ A) Internal voltage B) Internal resistance C) External resistance D) All the above

Last Answer : In a battery, the difference between the no-load voltage and the measured voltage output is called Internal resistance

Description : Describe physical quantity and examples

Last Answer : The quantities which can be measured are called physical quantity. Examples: Time, Mass, Length, volume etc.

Description : Measurement of a non -electrical quantity involves the following four subsystems:  a) amplifier block b) display block c) instrumentation block d) transducer block  The correct, sequence in which these block occur is  (1) d,a,c,b (2) d, c, a, b (3) a, c, b, d (4) a, b, c, d

Last Answer : Measurement of a non -electrical quantity involves the following four subsystems:  a) amplifier block b) display block c) instrumentation block d) transducer block  The correct, sequence in which these block occur is d,a,c,b

Last Answer : Integrating instruments are those which measure the total quantity of electricity delivered in a particular time.

Description : Explain Briefly The Trap Input For The 8085.?

Last Answer : Answer :The TRAP input is sensitive to both edge and level. The pulse width for this signal should be in excess as compared to the normal noise width. A second trap will never be able to ... to low transition. The pulse widths are wider than normal widths so as to prevent unwanted false triggers.

Description : How to Fix a Laptop Power Input

Last Answer : How to Fix a Laptop Power Input Besides extra battery chargers, your laptop charges the battery through the DC jack found at the side of the laptop case. Often, it is not the battery or the ... , it's best to check your warranty for instructions on where you should take the laptop for repair.

Description : A network is said to be under resonance when the voltage and the current at the network input terminals are (A) in phase (B) out of phase (C) in phase quadrature (D) in phase, and have equal magnitudes

Last Answer : A network is said to be under resonance when the voltage and the current at the network input terminals are in phase

Description : Is the input impedance of MOSFET more than BJT and FET?

Last Answer : Yes, the input impedance of MOSFET more than BJT and FET.

Description : Analyze the effect of supply voltage on performance of LED as regards current, Lumen output, efficacy and life. 

Last Answer : 1) Effect on Current:- In LED current depends upon supply voltage, if voltage get changes then current also change but this change in current will be control by resistors which are connected in series.  2) ...   4) Effect on Life:- If supply voltage is not stable then life of LED get reduced. 

Description : Explain DC coupled drive circuit with unipolar output.

Last Answer : DC coupled drive circuit with unipolar output: The figure shows the circuit and waveforms

Description : Write any four advantages of instrument transformer.

Last Answer : Advantages of instrument transformer: 1. Extension of instrument range is possible. 2. Isolation of instruments from high voltage side. 3. Power loss is less as compared to shunts and multipliers. 4 ... measurement. 5. It is economical method of range extension. 6. Increases in safety of operator.

Description : State the meaning of secondary instrument. Classify secondary instruments.

Last Answer : Secondary instruments: - Gives reading directly of the quantity being measured. - Calibrated with respect to absolute instruments  Classification of Secondary instruments:  1. Depending on the ... on permissible error: i) Standard meters ii) Substandard meters iii) First grade instruments.

Description : State the function of former and control spring in PMMC instrument.

Last Answer : Function of Former: To support the coil and provide eddy current damping.  Function of Control Spring: To provide control torque or force and in some instruments springs can be used as current leads.

Description : Describe spring control method of producing controlling torque in measuring instrument. Write any two properties required for spring material.

Last Answer : A)Spring control method: As shown in the figure, the inner ends of the both springs are attahced to the spindle, while outer end of upper spring is attached to the lever and outer ... of spring material: 1.Non Magnetic material 2.Low specific resistance 3.Low temperature coefficient of resistance

Description : Name the different torque and their function in measuring instrument.

Last Answer : List of torques in analog instruments:  1. Deflecting torque  2. Controlling / restraining torque.  3. Damping torque.  1. Deflecting torque:  - To create deflection of pointer ... .  - Bring the pointer to standstill quickly.  - To minimize oscillations about final position. 

Description : Give the classification of the errors used in measuring instrument & state the reason for their occurrence.

Last Answer : Types of errors in measuring instruments:  A) Gross error: These are due to mistakes on the part of person using the instrument.  B) Systematic Error:  i) Instrumental Error: These ... multiplying factor.  C) Random error: These persist even after gross and systematic errors are removed. 

Description : Name the material used for :- (i) Moving coil (ii) Permanent magnet in PMMC instrument.

Last Answer : (i) Material used for Moving coil: Copper, Aluminum( some times)  (ii) Permanent magnets are made of special alloys such as :  Aluminum-Nickel-Cobalt (Alnicos)  Strontium-Iron  Neodymium-Iron-Boron  Samarium-Cobalt.

Description : State the meaning of absolute instrument and secondary instrument. 

Last Answer : Absolute instruments:   These instruments read the quantity under measurement indirectly i.e. in terms of deflection, degrees and meter constant. The actual value under measurement can be calculated ... of operation (b) Depending upon permissible percentage error. (c) Depending upon application.

Description : State the advantages of instrument transformer in using for extension of range of meters. 

Last Answer : Advantages of instrument transformer: 1. Extension of instrument range is possible. 2. Isolation of instruments from high voltage side. 3. Power loss is less as compared to shunts and multipliers. 4 ... measurement. 5. It is economical method of range extension. 6. Increases in safety of operator.

Description : Explain magnetic effect employed in measuring instrument.

Last Answer : Magnetic Effect:  I) In PMMC meters:  ➢ When a current is passed through a conductor, magnetic field is produced round the conductor. Due to this field when current ... field it experiences a mechanical force.  Examples: Electrodynamometer type instruments, Induction type instrument. 

Description : State the function of controlling torque in electrical measuring instrument.

Last Answer : Function of controlling torque  1. The function is to opposes the deflection force and increases with the increase in the deflection of the moving system, to limit its movement. 2. and brought ... set a position where the two opposing forces i.e. deflection and controlling forces are equal. 

Description : Explain construction & working of attraction type M.I. instrument with neat diagram.

Last Answer : 1. Moving element: a small piece of soft iron in the form of a vane or rod.  2. In Attracted type a cylindrical coil or solenoid which is kept fixed. An oval-shaped soft-iron piece are ...   9. When = the pointer will be stable & we can get correct reading of the electrical quantity

Description : Why energy meter is integrating type measuring instrument?

Last Answer : Energy Meter is Integrating Type Measuring Instrument: Energy meter is used for measurement of energy, which is obtained by integration (summation) of power supplied over the particular time duration, hence it the integrating type measuring instrument. 

Description : Write any two advantages of MI type instrument.

Last Answer : Advantages of MI Type Instrument: 1. These are robust in construction. 2. Used for both A.C. as well as D.C. measurements. 3. These are economical. 4. These possess high operating torque 5. These are simple in construction hence can be easily handled.

Description : State working principle of PMMC instrument.

Last Answer : Working Principle of PMMC Instrument: When current carrying conductor is placed in a constant magnetic field, it experiences a force proportional to the current and produces proportional deflection torque. 

Description : Write difference between absolute & secondary instrument.

Last Answer : Absolute Instrument Secondary Instrument 1. These give magnitude of quantity in terms physical constants of instruments 1. These give reading directly of the quantity at the time of ... Raleigh current balance. 6. Examples - ammeter, voltmeter, amperehour meter, wattmeter etc.

Description : Compare PMMC & MI instrument.

Last Answer : MI Instrument  PMMC Instrument  It works on the principles of magnetism.  It works on the principle of DC motor Deflection torque is proportional to square of current  Deflection ... , Voltmeter and Watt meter  Can be used as voltmeter, Ammeter, Galvanometer, ohmmeter  

Description : Which is greater, 17,200,000 or 144 million?

Last Answer : Seventeen million or one hundred forty four million? I’ll take the 144 million, Alex!

Description : If you have a house with 12 bedrooms and it is just you living there, what would you do with all the extra bedrooms?

Last Answer : If I had such a house, I'd probably sell it. Seems like a complete waste of space for one person. However, if for some reason I couldn't sell it or it wasn't a financially good time to sell ... I could find some way of vetting the people to ensure they were responsible and safe to have in my home.

Description : Where in the Seattle area would you go to get a very large number of excellent tamales for a party? Homemade, not Taco Bell, not that Taco Bell has tamales anyway, the jerks.

Last Answer : Here are some reviews that might help. Happy birthday, @susanc!

Description : A 40 W bulb is connected in series with a room heater. If now 40 W bulb is replaced by 100 W bulb, the heater output will?

Last Answer : A 40 W bulb is connected in series with a room heater. If now 40 W bulb is replaced by 100 W bulb, the heater output will increase.

Description : The ratio of maximum displacement deviation to full scale deviation of the instrument is called?

Last Answer : The ratio of maximum displacement deviation to full scale deviation of the instrument is called linearity.

Description : What are the test and measuring instrument required in an Electrical depots?

Last Answer : Ans. Following are the test and measuring instruments required in an Electrical depots. a. Test lamp b. Line Tester c. Continuity tester d. Volt meter e. Ammeter f. Earth megger g. Megger h. Lux meter i. Power analyzer j. Infrared thermometer

Description : List two advantages of PMMC instrument.

Last Answer : 1. It has uniform scale. 2. Power consumption is low 3. It can be obtained in wide ranges. 4. High sensitivity & accuracy 5. It is unaffected by external magnetic field. 6. Additional damping device not required. 7. Hysteresis problem is not there.

Description : need of calibration and explain the procedure to calibrate the instrument.

Last Answer : Need of calibration: Every measuring device degrades over time due to normal wear and tear. These changes can be caused by various reasons such as electric or mechanical shock or a hazardous manufacturing ... different magnitude are used to calculate the resistance based on ohm's law.

Description : feature of PMMC instrument. 

Last Answer : Consumes less power Great accuracy. High torque to weight ratio

Description : A Pyrheliometer is an instrument to measure :  (A) temperature of solar photovoltaic cell  (B) intensity of direct solar radiation at normal incidence  (C) intensity of indirect solar radiation  (D) efficiency of a solar photovoltaic cell

Last Answer : A Pyrheliometer is an instrument to measure : intensity of direct solar radiation at normal incidence 

Description : In a PMMC instrument, the damping provided is :  (A) air damping (C) eddy current damping (B) fluid damping (D) magnetic damping using a magnet

Last Answer : In a PMMC instrument, the damping provided is : eddy current damping 

Description : A PMMC instrument has FSD of 100 μA and a coil resistance of 1 kΩ. To convert the instrument into an ammeter with full scale deflection of 100 mA, the required shunt resistance is (A) 1 Ω (B) 1.001 Ω (C) 0.5 Ω (D) 10 Ω

Last Answer : A PMMC instrument has FSD of 100 μA and a coil resistance of 1 kΩ. To convert the instrument into an ammeter with full scale deflection of 100 mA, the required shunt resistance is 1.001 Ω

Description : Eddy current damping cannot be used for moving iron instrument because

Last Answer : Eddy current damping cannot be used for moving iron instrument because the presence of a permanent magnet required for such purpose would affect the deflection and hence the reading of the instrument

Description : Identify the instrument that does not exist (A) Dynamo-meter type ammeter (B) Dynamo-meter type wattmeter (C) Moving-iron voltmeter (D) Moving-iron wattmeter

Last Answer : Identify the instrument that does not exist (A) Dynamo-meter type ammeter (B) Dynamo-meter type wattmeter (C) Moving-iron voltmeter (D) Moving-iron wattmeter

Description : An instrument which detects electric current is known as?

Last Answer : An instrument which detects electric current is known as galvanometer.