If the fault current is 2000 A, the relay setting is 50% and CT ratio is 400:5, the plug setting multiplier will be

If the fault current is 2000 A, the relay setting is 50% and CT ratio is 400:5, the plug setting multiplier will be
by

1 Answer

Answer :

If the fault current is 2000 A, the relay setting is 50% and CT ratio is 400:5, the plug setting multiplier will be 10 A

by

Related questions

If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug

Description : If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug setting multiplier will be

Last Answer : If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug setting multiplier will be 10

If the % reactance upto the fault point is 20%, then the short circuit current will be

Description : If the % reactance upto the fault point is 20%, then the short circuit current will be

Last Answer : If the % reactance upto the fault point is 20%, then the short circuit current will be 5 times the full load current

The inverse definite mean time relays are used for over current and earth fault protection of transformer against?

Last Answer : The inverse definite mean time relays are used for over current and earth fault protection of transformer against internal short-circuits.

In which fault the maximum short circuit current occurs?

Description : In which fault the maximum short circuit current occurs?

Last Answer : In three phase bolted fault the maximum short circuit occurs.

If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded

Description : If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded transformer, then  (A) zero sequence currents are present on both sides of the transformer  (B) ... side  (D) zero sequence currents are present on the primary side but not on the secondary side

Last Answer : If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded transformer, then zero sequence currents are absent on both sides of the transformer 

A shunt fault is characterized by

Description : A shunt fault is characterized by (A) Increase in current, frequency and pf (B) Increase in current, reduction in frequency and pf (C) Increase in current and frequency, reduction in pf (D) Decrease in current and frequency

Last Answer : B

Which relay is preferred for phase fault on short transmission line?

Last Answer : Reactance relay is preferred for phase fault on short transmission line.

Give the causes and impact and reasons of grid system fault.

Description : Give the causes and impact and reasons of grid system fault. 

Last Answer : Following are the causes/reasons grid system fault: 1. Major imbalance between generation and consumption i.e. demand is more than generation. 2. Low frequency, due to some faults the frequency ... of supply and causes inconvenience to people. 6. Disturb the routine work of common all people.

With fault clearing time, the transient stability of a power system

Description : With fault clearing time, the transient stability of a power system

Last Answer : With fault clearing time, the transient stability of a power system decreases

To protect the power transformer (Y-Y with neutral grounded) against fault, what type of connection do the CTs have ?

Description : To protect the power transformer (Y-Y with neutral grounded) against fault, what type of connection do the CTs have ?

Last Answer : To protect the power transformer (Y-Y with neutral grounded) against fault, what type of connection do the CTs have ? Δ-Δ connection

Fault diverters are basically?

Last Answer : Fault diverters are basically fast switches.

Which is the most common type of fault?

Description : Which is the most common type of fault?

Last Answer : Single phase to ground fault is the most common type of fault.

Define the following terms with respect to protective relays i) Relay time ii) Reset current iii) Plug setting multiplier and iv) Time setting multiplier

Description : Define the following terms with respect to protective relays i) Relay time ii) Reset current iii) Plug setting multiplier and iv) Time setting multiplier

Last Answer : 1) Relay Time: The time interval between occurrence of fault and closure of relay contacts.  2) Reset Current: The value of current below which the relay resets and comes back to ... The adjustment arrangement provided for setting the operation time of relay is known as Time setting multiplier. 

The skin effect in conductors is due to non uniform distribution of current in it and major portion of current is

Description : The skin effect in conductors is due to non uniform distribution of current in it and major portion of current is near the _______ of conductor.  (1) Surface (2) Center (3) Complete cross section area (4) Axis

Last Answer : The skin effect in conductors is due to non uniform distribution of current in it and major portion of current is near the Surface of conductor. 

In parallel RLC resonance circuit at resonance the current will be

Description : In parallel RLC resonance circuit at resonance the current will be  (1) Minimum (2) Maximum (3) Zero (4) Infinite

Last Answer : In parallel RLC resonance circuit at resonance the current will be Minimum 

The sequence components of current of a single-phase load connected to a 3-phase system are

Description : The sequence components of current of a single-phase load connected to a 3-phase system are (A) equal positive and negative sequence components (B) equal positive, negative and zero sequence components (C) vector sum of sequence currents is zero (D) algebraic sum of sequence currents is zero

Last Answer : The sequence components of current of a single-phase load connected to a 3-phase system are equal positive, negative and zero sequence components

Precise control of reactive current flow entering the transmission and distribution systems can be minimized

Description : Precise control of reactive current flow entering the transmission and distribution systems can be minimized by using (A) synchronous condenser (B) static VAR capacitor (C) capacitor bank (D) thyristor switched reactor in parallel with capacitor

Last Answer : Precise control of reactive current flow entering the transmission and distribution systems can be minimized by using (A) synchronous condenser (B) static VAR capacitor (C) capacitor bank (D) thyristor switched reactor in parallel with capacitor

Plug Setting Multiplier (PSM) is the ratio of

Description : Plug Setting Multiplier (PSM) is the ratio of (a) secondary current/relay current (b) secondary current/primary current (c) secondary current/relay current setting (d) none of these

Last Answer : PSM = fault current on the relay coil/pick up current.

In the induction type directional over current relay, when a short-circuit occurs in the circuit

Description : In the induction type directional over current relay, when a short-circuit occurs in the circuit (A) power flows in reverse direction (B) power flows in normal direction (C) directional power element does not operate (D) over current element is not energized

Last Answer : In the induction type directional over current relay, when a short-circuit occurs in the circuit power flows in reverse direction

In order that current should flow without causing excessive heating or voltage drop, the relay contacts should?

Last Answer : In order that current should flow without causing excessive heating or voltage drop, the relay contacts should have low contact resistance, be clean and smooth, be of sufficient size and proper shape.

The eddy current loss in a dc generator is 400 W at 40 Hz frequency of reversal and constant flux density.

Description : The eddy current loss in a dc generator is 400 W at 40 Hz frequency of reversal and constant flux density. When frequency is increased to 50 Hz., eddy current loss is :  (A) 256 W (B) 320 W (C) 500 W (D) 625 W

Last Answer : The eddy current loss in a dc generator is 400 W at 40 Hz frequency of reversal and constant flux density. When frequency is increased to 50 Hz., eddy current loss is : 625 W

Define: (1) Plug setting multiplier (2) Time setting multiplier

Description : Define: (1) Plug setting multiplier (2) Time setting multiplier

Last Answer : Plug setting multiplier (PSM): It is related to the current setting of the overcurrent relays. The plug setting multiplier is defined as the ratio of the transformed fault current on the relay side' to ... .4 seconds.  Thus TSM is used to define the steps for time setting of relay operation.

Ravi, Rakesh and Vijay invest in a partnership in the ratio 7/2, 4/3, 6/5 respectively. After 4 months, Ravi increases his share 50%. If the total profit at the and of one year be Rs. 32,400, then what is Rakesh's share in the profit? 1) Rs. 2000 2) Rs. 3000 3) Rs. 4000 4) Rs. 5000 5) Rs. 6000

Description : Ravi, Rakesh and Vijay invest in a partnership in the ratio 7/2, 4/3, 6/5 respectively. After 4 months, Ravi increases his share 50%. If the total profit at the and of one year be Rs. 32,400, then what is Rakesh's ... the profit? 1) Rs. 2000 2) Rs. 3000 3) Rs. 4000 4) Rs. 5000 5) Rs. 6000

Last Answer : 5) Rs. 6000

Current ratio

Description : Current ratio

Last Answer : Current ratio

Define: 1) voltage ratio, 2) current ratio, 3) transformation ratio of transformer.

Description : Define: 1) voltage ratio, 2) current ratio, 3) transformation ratio of transformer.

Last Answer : 1) Voltage ratio: The voltages in primary and secondary winding is proportional to number of turns in primary and secondary respectively. So, the voltage ratio is same as transformation ratio. V2/V1 = N2 ... as transformation ratio of transformer. It is denoted by K. K = N2/N1

Analyze the effect of supply voltage on performance of LED as regards current, Lumen output, efficacy and life.

Description : Analyze the effect of supply voltage on performance of LED as regards current, Lumen output, efficacy and life. 

Last Answer : 1) Effect on Current:- In LED current depends upon supply voltage, if voltage get changes then current also change but this change in current will be control by resistors which are connected in series.  2) ...   4) Effect on Life:- If supply voltage is not stable then life of LED get reduced. 

With the help of N-channel JFET describe the effect of input voltage VGS on output current ID.

Description : With the help of N-channel JFET describe the effect of input voltage VGS on output current ID.

Last Answer : Working of N channel FET: * When a voltage is applied between the drain and source with a DC supply (VDD), the electrons flows from source to drain through narrow channel ... where the channel gets completely blocked and the drain current becomes zero is called pinch- off voltage. 

Define: i) Input Offset Voltage ii) Input offset Current iii) Input Bias Current iv) Output offset voltage

Description : Define: i) Input Offset Voltage ii) Input offset Current iii) Input Bias Current iv) Output offset voltage

Last Answer : Definition of parameters of OPAMP is follows:  i) Input Offset Voltage: Input offset voltage is defined as the voltage that must be applied between the two input terminals of an OPAMP to null or ... to ground) and output voltage is obtained non zero such voltage is output offset voltage of opamp.

Current division rule example

Description : Current division rule example

Last Answer : Current division rule example

A linear network has a current input 4cos(ω t + 20º)A and a voltage output 10 cos(ωt +110º) V. Determine the associated impedance.

Description : A linear network has a current input 4cos(ω t + 20º)A and a voltage output 10 cos(ωt +110º) V. Determine the associated impedance.

Last Answer : Solution

Find current through resistor using nodal analysis

Description : Find current through resistor using nodal analysis

Last Answer : Find current through resistor using nodal analysis

Nodal analysis problem two current source

Description : Nodal analysis problem two current source

Last Answer : Nodal analysis problem two current source

Direct Current (DC)

Description : Direct Current (DC) Next Topic : Alternating current (AC)

Last Answer : Direct Current (DC) is the unidirectional electric current. Uni meaning is one. And the flow of charge in same direction. We know that conventional current flow from positive terminal of battery to ... The magnitude of DC may constant or vary but direction do not change with respect to time.

Alternating current (AC)

Description : Alternating current (AC)

Last Answer : AC stands for Alternating Current meaning voltage or current that changes polarity or direction respectively over time. An Alternating Current (AC) is an electric current whose magnitude ... energy are known as alternators and are simpler construction than DC electromechanical generators.

Does current flow through a capacitor ?

Description : Does current flow through a capacitor ?

Last Answer : Imagine a pipe with a flexible diaphram in the middle separating two haves of the pipe. Now the pipe is filled with air. If you apply a pressure to one end the diaphram will deform ... capacitor, the effects on electrons will be recreated across the boundary. But theres no electrical connection...

What kills, current or voltage?

Description : What kills, current or voltage?

Last Answer : Current would kill. You can actually have thousands of bolts going through you and not even know it. Yes you probably know already voltage is current times resistance. Since your body is a resistor it would take just a small amount of current to create a very high voltage

Electric Current

Description : Electric Current

Last Answer : Electric current is the flow of charges. The electrons flow from higher density area of electrons to lowers density area of electrons. The terminal of battery which we called positive terminal of ... circuit is called electric current. The unit of electric current is Coulomb per Second or Ampere.

Define current. State its unit.

Description : Define current. State its unit.

Last Answer : Electric current: It is a measure of the amount of electrical charge transferred per unit time. It represents the flow of electrons through a conductive material, such as a metal wire. Unit: 1 coulomb/second. OR Its unit is ampere represented by A

Give two applications of each : 1) Eddy current sensor 2) Optical sensor.

Description : Give two applications of each : 1) Eddy current sensor 2) Optical sensor.

Last Answer : Eddy current sensor : 1. Detection of non-magnetic but conductive materials. 2. Displacement sensing 3. Position sensing Optical sensor : 1. Position Detection 2. Velocity Detection 3. Acceleration Detection 4. Direction Detection

Alternating current

Description : Alternating current

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

A charge of 0.1 C moves past a given point every 0.01 s. How much is the current?

Description : A charge of 0.1 C moves past a given point every 0.01 s. How much is the current?

Last Answer : The current is 10.0A.  1ampere = 1 Coulomb per 1 second.  0.1Coulombs ÷ 0.01seconds = 10.0amperes.

Describe the difference between direct and alternating current.

Description : Describe the difference between direct and alternating current.

Last Answer : Direct current is the flow of electricity or charge in one direction..  Alternative current is the flow of charge that doesn't flow in one direction. 

What is the unit of electric current?

Description : A) Watt B) Volts C) Farad D) Ampere

Last Answer : Correct answer: D) Ampere

Current divider rule

Description : Current divider rule

Last Answer : Current divider rule

Current formula

Description : Current formula

Last Answer : Current formula

Capacitive current formula

Description : Capacitive current

Last Answer : Capacitive current formula

How to find total impedance Z, current I and Impedance angle ?

Description : How to find total impedance Z, current I and Impedance angle ?

Last Answer : How to find total impedance Z, current I and Impedance angle ?

Why inductor current lags inductor voltage ?

Description : Why inductor current lags inductor voltage ?

Last Answer : Inductor is a wire wounding structure having a core material it induces emf which is opposite to the voltage supply and proportional to rate of change of current so current lags the voltage in inductor

Explain lagging quantity and leading quantity, explain this concept with voltage and current waveform

Description : Explain lagging quantity and leading quantity, explain this concept with voltage and current waveform

Last Answer : When two alternating quantities attain their respective zero or peak values simultaneously, the quantities are said to be in-phase quantities. When the quantities do not attain their respective zero or ... current is leading the voltage or the voltage is said to be lagging behind the current.

List out any four effects of electric current used in measuring instruments & write name of meter working on it.

Description : List out any four effects of electric current used in measuring instruments & write name of meter working on it.

Last Answer : Effects of Electric Current used in measuring instruments:  1. Magnetic Effect: PMMC and Moving Iron type Ammeters, voltmeter and Dynamometer type wattmeters etc.  2. Electromagnetic induction ... . Electrostatic effect: Voltmeters.  5. Hall Effect: Flux meter, Poynting vector wattmeter.