Measurement of a non -electrical quantity involves the following four subsystems:

Measurement of a non -electrical quantity involves the following four subsystems: 

a) amplifier block b) display block c) instrumentation block d) transducer block 

The correct, sequence in which these block occur is 

(1) d,a,c,b (2) d, c, a, b (3) a, c, b, d (4) a, b, c, d
by

1 Answer

Answer :

Measurement of a non -electrical quantity involves the following four subsystems: 

a) amplifier block b) display block c) instrumentation block d) transducer block 

The correct, sequence in which these block occur is d,a,c,b

by

Related questions

Which instruments are those which measure the total quantity of electricity delivered in a particular time?

Last Answer : Integrating instruments are those which measure the total quantity of electricity delivered in a particular time.

Two non -inverting amplifiers, one having a unity gain and the other having again of twenty are made using

Description : Two non -inverting amplifiers, one having a unity gain and the other having again of twenty are made using identical operational amplifiers. As compared to the unity gain amplifier, the amplifier with gain twenty has

Last Answer : Two non -inverting amplifiers, one having a unity gain and the other having again of twenty are made using identical operational amplifiers. As compared to the unity gain amplifier, the amplifier with gain twenty has less bandwidth

For measurement of radio frequency ac signals __________ type meter is used

Description : For measurement of radio frequency ac signals __________ type meter is used

Last Answer : For measurement of radio frequency ac signals thermo-couple type meter is used

Accurate measurement of very low resistances is possible with

Description : Accurate measurement of very low resistances is possible with (A) Megger (B) Wheatstone Bridge (C) Kelvin’s Double Bridge (D) Wagner’s Earthing Device

Last Answer : Accurate measurement of very low resistances is possible with Kelvin’s Double Bridge

Commonly used instruments in power system measurement are?

Last Answer : Commonly used instruments in power system measurement are induction.

For measurement of inductance having high value, we should use?

Last Answer : For measurement of inductance having high value, we should use Hay's bridge.

For measurement of mutual inductance we can use?

Last Answer : For measurement of mutual inductance we can use Heaviside bridge.

In a 3-phase power measurement by two wattmeter method, both the wattmeters had identical readings...

Description : In a 3-phase power measurement by two wattmeter method, both the watt meters had identical readings. The power factor of the load was?

Last Answer : In a 3-phase power measurement by two wattmeter method, both the watt meters had identical readings. The power factor of the load was unity.

Define measurement and state the significance of electrical measurement system.

Description : Define measurement and state the significance of electrical measurement system.

Last Answer : Measurement: Measurement is essentially a process in which magnitude of a quantity is determined in comparison with another similar quantity with significant units. OR The measurement of a given ... x) The measurement conforms the validity of hypothesis and also adds to its understanding.

Explain significance and purpose of electrical measurement system.

Description : Explain significance and purpose of electrical measurement system.

Last Answer : ➢ Significance of Electrical Measurement System  1. The measurement is required for measurement of all physical quantities for e.g speed, velocity, temperature, pressure etc.  2. All electrical ... 4. These standards and references may changes time to time, area to area person to person 

Describe physical quantity and examples

Description : Describe physical quantity and examples

Last Answer : The quantities which can be measured are called physical quantity. Examples: Time, Mass, Length, volume etc.

Explain lagging quantity and leading quantity, explain this concept with voltage and current waveform

Description : Explain lagging quantity and leading quantity, explain this concept with voltage and current waveform

Last Answer : When two alternating quantities attain their respective zero or peak values simultaneously, the quantities are said to be in-phase quantities. When the quantities do not attain their respective zero or ... current is leading the voltage or the voltage is said to be lagging behind the current.

‘PMMC instrument is not suitable to measure AC quantity’. State the reason.

Description : ‘PMMC instrument is not suitable to measure AC quantity’. State the reason.

Last Answer : The direction of force exerted on moving coil depends on the direction of current flowing through moving coil. If the direction of magnetic field is kept constant, it produces unidirectional torque if the current is ... on the coil in one cycle to zero. Hence the meter cannot read A.C. quantities.

The largest change of input quantity for which there is no output of instrument is called ______

Description : The largest change of input quantity for which there is no output of instrument is called ______ A) Dead time B) Dead input C) Dead output D) Dead zone

Last Answer : The largest change of input quantity for which there is no output of instrument is called Dead zone

can induction heating is use for both magnetic and non magnetic material ?

Last Answer : Yes, Induction heating is used for both magnetic and non-magnetic materials.

Did you realize the double standards here at fluther?

Description : Did you realize the double standards here at fluther?

Last Answer : Not to sound bossy; but Take a deep breath, turn off your computer, go for a walk around the block, when you get back take a long hot bath & then go to bed. Tomorrow morning will be a new day ... won't seem so major. I've lost 10 pounds since joining Fluther from my walks around the block!!! LoL

Units of Measurement

Description : Units of Measurement

Last Answer : 1 horse power is 745.7 watts 1 horse power = work equal to lifting 550 lbs of weight to one foot for one second 1 calorie is equal to 4.2 Joules 1 barrel is equal to ... often chlorine or bromine. Use: as solvents, as aerosol propellants, in refrigeration. It is commonly used in refrigerator.

List the different level measurement methods.

Description : List the different level measurement methods. 

Last Answer : Liquid Level Measurement Direct method 1. Hook type 2. Sight glass gype 3. Float type 4. Dip stick Indirect method 1. Hydraustatic pressure type 2. Electrical type a) Capacitance level indicator b) Radiation level detector c) Ultrasonic level gauge 3. Radar type

Draw Bourdon tube with LVDT setup for pressure measurement.

Description : Draw Bourdon tube with LVDT setup for pressure measurement.

Last Answer : Bourdon tube with LVDT setup for pressure measurement.

sketch time period measurement by CRO.

Description : sketch time period measurement by CRO.

Last Answer : Horizontal sweep is turned ON and the display appealing on the screen is adjusted by varying different control knobs provided on the front panel of CRO, till the signal is suitably displayed ... Where m=Number of division in one complete cycle n=Setting of time base =Time/Division

different types of errors occurs in measurement.

Description : different types of errors occurs in measurement.

Last Answer : Generally errors are classified into three types: systematic errors, random errors and blunders. 1) Gross Errors 2) Random Errors 3) Systematic Errors Instrumental Errors Environmental ... to wrong observations or reading in the instruments particularly in case of energy meter reading. 

tern null as it applies to bridge measurement.

Description : tern null as it applies to bridge measurement.

Last Answer : Null measurements balance voltages so that there is no current flowing through the measuring device and, therefore, no alteration of the circuit being measured. Null measurements are generally more ... the use of standard voltmeters and ammeters, and they still have limits to their precision.

State how pressure measurement can be done using Dead weight tester.

Description : State how pressure measurement can be done using Dead weight tester.

Last Answer : The handle is fully drawn out and the oil is allowed to enter in the cylinder (i.e. gauge and piston) The weight to be measured is placed on the platform. Now the handle is turned ... of the area of the piston and the pressure indicated on the gauge is equal to the weight under measurement.

Name two methods for measurement of low, medium and high resistance. Give one advantage and one limitation of V- I method.

Description : Name two methods for measurement of low, medium and high resistance. Give one advantage and one limitation of V- I method.

Last Answer : Methods for measurement of low resistance:  1. Ammeter voltmeter method  2. Kelvin's bridge method  3. Ohm meter method  4. Potentiometer method  5. Digital/analog multi-meter ... must be infinity for perfectly accurate measurement which is not possible.  2. Connection errors.

State the significance of term measurement.

Description : State the significance of term measurement. 

Last Answer : Measurement is the quantitative comparison between unknown quantities with known standard. For doing this process there is need of physical device, called as measuring instrument. The measurement confirms the validity of the hypothesis and also adds to its understanding.

Describe with working of LCR meter for measurement of inductance.

Description : Describe with working of LCR meter for measurement of inductance. 

Last Answer : working of LCR:- A LCR meter (Inductance (L), Capacitance (C), and Resistance (R) test equipment used to measure the inductance, capacitance and, resistance of a component. It works on the ... in parallel (as would be encountered in measuring a capacitor with a leaky dielectric) [Q setting ] 

State any two disadvantages of one wattmeter method of measurement of 3 phase power.

Description : State any two disadvantages of one wattmeter method of measurement of 3 phase power.

Last Answer : State any two disadvantages of one wattmeter method of measurement of 3 phase power. Disadvantages of one wattmeter method:- 1. Only used for balanced load 2. It can not be used for ... connection then neutral point must be available 4. Delta connection must be opened to connect current coil.

Explain V- I method of measurement of medium resistance.

Description : Explain V- I method of measurement of medium resistance. 

Last Answer : In this method, use suitable source, ammeter and voltmeter and connect them as shown in the above diagram. Take reading of voltmeter and ammeter, then value of resistance = R = V/I Ω To minimise the error take 4 to 5 observation for the same resistance and take their average.

What are the factors influencing measurement errors?

Description : What are the factors influencing measurement errors?

Last Answer : The factor influencing measurement errors are accuracy, precision, range and bandwidth, sensitivity, resolution and uncertainty.

The bridge most suited for accurate measurement of relative permittivity of dielectric materials is

Description : The bridge most suited for accurate measurement of relative permittivity of dielectric materials is (A) Carey Foster Bridge (B) Anderson’s bridge (C) Heaviside Bridge modified by Campbell. (D) Schering Bridge.

Last Answer : The bridge most suited for accurate measurement of relative permittivity of dielectric materials is Schering Bridge.

What is measurement error ?

Description : What is measurement error ?

Last Answer : Measurement error :- Measurement is the process of comparing unknown quantity with known or standard quantity. Error is the difference between ... by fluctuations in reading measurement apparatus. Random error show different result for same repeated measurement.

Which is greater, 17,200,000 or 144 million?

Description : Which is greater, 17,200,000 or 144 million?

Last Answer : Seventeen million or one hundred forty four million? I’ll take the 144 million, Alex!

If you have a house with 12 bedrooms and it is just you living there, what would you do with all the extra bedrooms?

Description : If you have a house with 12 bedrooms and it is just you living there, what would you do with all the extra bedrooms?

Last Answer : If I had such a house, I'd probably sell it. Seems like a complete waste of space for one person. However, if for some reason I couldn't sell it or it wasn't a financially good time to sell ... I could find some way of vetting the people to ensure they were responsible and safe to have in my home.

Where in the Seattle area would you go to get a very large number of excellent tamales for a party? Homemade, not Taco Bell, not that Taco Bell has tamales anyway, the jerks.

Description : Where in the Seattle area would you go to get a very large number of excellent tamales for a party? Homemade, not Taco Bell, not that Taco Bell has tamales anyway, the jerks.

Last Answer : Here are some reviews that might help. Happy birthday, @susanc!

What are the terms for the dimensions of a box? See detail.

Description : What are the terms for the dimensions of a box? See detail.

Last Answer : Length, width, height.

For measuring an unknown electrical quantity, select the meter with

Last Answer : For measuring an unknown electrical quantity, select the meter with Highest range and work down.

What subsystems are in a lamp?

Description : What subsystems are in a lamp?

Last Answer : A subsystem for a lamp would be the bulb because the bulb letsthe eye see.

Batteries are used to power all satellite subsystems A. at all times B. only during emergencies C. during eclipse periods D. to give the solar arrays a rest

Description : Batteries are used to power all satellite subsystems A. at all times B. only during emergencies C. during eclipse periods D. to give the solar arrays a rest

Last Answer : C. during eclipse periods

In ……………… system the interaction between various subsystems cannot be defined with certainty A) Open System B) Closed System C) Deterministic System D) Probabilistic System

Description : In ……………… system the interaction between various subsystems cannot be defined with certainty A) Open System B) Closed System C) Deterministic System D) Probabilistic System

Last Answer : D) Probabilistic System

The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm

Description : The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm (A) Wien’s bridge (B) Kelvin double bridge (C) Maxwell’s bridge (D) Shering Bridge

Last Answer : The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm (A) Wien’s bridge (B) Kelvin double bridge (C) Maxwell’s bridge (D) Shering Bridge

Which of the following instruments can be used for measurement of very high value resistances such as

Description : Which of the following instruments can be used for measurement of very high value resistances such as insulation resistance in industries? A) Wheatstone bridge B) Megger C) Ohm-meter D) Resistive potentiometer 

Last Answer : Which of the following instruments can be used for measurement of very high value resistances such as insulation resistance in industries? A) Wheatstone bridge B) Megger C) Ohm-meter D) Resistive potentiometer 

In the measurement of power of balanced load by two wattmeter method in a 3-phase circuit, The readings

Description :  In the measurement of power of balanced load by two wattmeter method in a 3-phase circuit, The readings of the wattmeters are 4 kW and 2 kW respectively, the later is being taken after reversing the connections of current coil. the ... kVAR B) 0.2 & 6 √3 kVAR C) 0.32 & 2 kVAR D) 0.32 & 2 √3 kVAR

Last Answer :  In the measurement of power of balanced load by two wattmeter method in a 3-phase circuit, The readings of the wattmeters are 4 kW and 2 kW respectively, the later is being taken after reversing the ... of current coil. the power factor and reactive power of the load is 0.2 & 6 √3 kVAR

The function of measurement system is/are _____.

Description : The function of measurement system is/are _____.

Last Answer : The function of measurement system are indicating, recording and controlling function.

For power measurement of three phase circuit by two wattmeter method, when the value of power factor

Description : For power measurement of three phase circuit by two wattmeter method, when the value of power factor is less than 0.5 lagging:

Last Answer : For power measurement of three phase circuit by two wattmeter method, when the value of power factor is less than 0.5 lagging: One of the wattmeter connections will have to be reversed

The measurement range of an ammeter can be increased by using a:

Description : The measurement range of an ammeter can be increased by using a:

Last Answer : The measurement range of an ammeter can be increased by using a: low resistance in shunt

Clamp on ammeter is used for measurement of:

Description : Clamp on ammeter is used for measurement of:

Last Answer : Clamp on ammeter is used for measurement of: large alternating currents

Weins bridge is used for measurement of frequency in the applied voltage waveform is measurement of

Description : Weins bridge is used for measurement of frequency in the applied voltage waveform is measurement of frequency in the applied voltage waveform is   (A)sinusoidal (B) square (C) rectangular (D) triangular

Last Answer : Weins bridge is used for measurement of frequency in the applied voltage waveform is measurement of frequency in the applied voltage waveform is sinusoidal 

Measurement of power and power factor of a 3-phase system by two wattmeter method can be

Description : Measurement of power and power factor of a 3-phase system by two wattmeter method can be obtained in case of  1. Balanced load and balanced source  2. Balanced source with 3-phase 3-wire unbalanced load  3. Unbalanced source with 3-phase 3 ... b) 2, 3 and 5 (c) 1, 2, 3, 4 and 5 (d) 1, 2, 3 and 5 

Last Answer : Measurement of power and power factor of a 3-phase system by two wattmeter method can be obtained in case of  1. Balanced load and balanced source  2. Balanced source with 3-phase 3-wire unbalanced load  3. Unbalanced source with 3- ... b) 2, 3 and 5 (c) 1, 2, 3, 4 and 5 (d) 1, 2, 3 and 5 

Integrating principle in the digital measurement is the conversion of

Description : Integrating principle in the digital measurement is the conversion of   (a) Voltage to time (b) Voltage to frequency (c) Voltage to current (d) Current to voltage

Last Answer : Integrating principle in the digital measurement is the conversion of Voltage to frequency