A four -quadrant operation requires two full converters connected in 

(1) Series (3) Back to back (2) Parallel (4) Series Cascade

1 Answer

Answer :

A four-quadrant operation requires two full converters connected in Parallel 

Related questions

Description : Describe the basic SHA operation with the help of its four mode specifications.

Last Answer : Sample-and-hold amplifier (SHA) is a unity gain amplifier with a mode control switch where the input of the amplifier is connected to a time-varying signal. A trigger pulse at the mode control switch ... but other forms, such as optical and mechanical forms, are possible. Also denoted S/H.

Description : Explain two-quadrant chopper.........

Last Answer : Two quadrant chopper:  There are two semiconductor controllable switches in the two-quadrant chopper. Two quadrant type A chopper: The figure shows the type A chopper. Both the switch never turn on at ... 2 are turned on then Vo=Vs. When chopper 1 and chopper 2 are off then Vo=-Vs.

Description : Explain SEPIC converters..............

Last Answer : SEPIC converter: SEPIC stands for single-ended primary inductor converter. SEPIC converter is a DC to DC converter, the output of SEPIC converter can be more than input voltage or less than ... . By controlling duty cycle of transistor the output of SEPIC converter can be controlled.

Description : What is the need of data converters? List specifications of DAC.

Last Answer : Need of data converters:  It is often necessary that before processing the analog data, by a digital system, it should be changed to an equivalent digital form. Similarly, after processing the data, it ... 4. Temperature sensitivity 5. Settling time 6. Speed 7. Long term Drift 8. Supply rejection

Description : In a 5 bit weighted resistor D/A converters, the resistor value corresponding to LSB is 40 kΩ, and the resistor value corresponding to MSB will be (A) 0.4 kΩ (B) 3 kΩ (C) 2.8 kΩ (D) 2.5 kΩ

Last Answer : In a 5 bit weighted resistor D/A converters, the resistor value corresponding to LSB is 40 kΩ, and the resistor value corresponding to MSB will be 2.5 kΩ 

Description : Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Last Answer : Single phase fully control bridge converter with RL load: 1. During positive half cycle of input voltage, T1 and T2 are forward biased and during negative half cycle, T3 and T4 are forward biased. Therefore, T1-T2 ... cycle till the firing of next pair of SCRs as shown in the waveform.

Description : Explain Three Phase Bidirectional Delta Connected Controller.

Last Answer : Three Phase Bidirectional Delta Connected Controller:

Description : With neat sketch explain four modes of operation of a TRIAC? 

Last Answer : Modes of operation of a TRIAC: There are four different operating modes of TRIAC:  1) MT2 and gate are positive with respect to terminal MT1(Mode1) : Here terminal MT2 is positive ... junction P2-N2 is forward biased, current carriers are injected and therefore, the TRIAC is turned on. 

Description : Explain the operation of UPS with a neat block diagram.

Last Answer : Uninterruptible-Power-Supplies (UPS): A block diagram of UPS system is shown in figure. It essentially consists of four major components: i)Rectifier (or battery charger) ii) ... . Due to fast action requirement, transfer switch can be implemented by fast acting semiconductor devices.

Description : Which of the following thyristors can be used for high frequency of operation? A) TRIAC B) DIAC C) SCR D) GTO 

Last Answer : Which of the following thyristors can be used for high frequency of operation? A) TRIAC B) DIAC C) SCR D) GTO 

Description : An additional condition for parallel operation of three-phase transformers over single-phase transformers is that

Last Answer : An additional condition for parallel operation of three-phase transformers over single-phase transformers is that the transformers should belong to the same vector group

Description : parallel operation of MOSFET can be done more easily as compared to thyristor. why?

Last Answer : Parallel operation of MOSFET can be done more easily as compared to thyristor because the resistance of MOSFET is increases with increase in temperature. MOSFET have the positive temperature coefficient. In ... the parallel operation of MOSFET can be done more easily as compared to the thyristor.

Description : Explain the series and parallel operation of MOSFET. Which is suitable and why?

Last Answer : Series operation of MOSFET: To increase voltage handling capability MOSFETs are connected in series. When the MOSFETs are connected in series each MOSFET should turn on and turn off ... on and turn off time and transconductance. Each MOSFET should share current equally.  

Description : Also, highlight the problem faced during parallel operation.

Last Answer : Parallel operation of IGBT: Parallel operation of IGBT is done for obtaining high current rating. Paralleling of IGBT reduces conduction losses and thermal stress. IGBT combines the qualities of ... . IGBTs must share losses equally otherwise IGBT may get failure due to thermal differences.

Description : Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it. 

Last Answer : Circuit Diagram: Waveforms:

Description : Draw full bridge & half bridge configuration with common cathode.

Last Answer : Half Bridge Configuration: Full Bridge Configuration: 

Description : Why the power factor of semiconverter is better than full converter?

Last Answer : Power factor of semiconverter is better than full converter

Description : Explain three phase full wave controller.

Last Answer : Three phase full wave controller: Three phase full wave controller is also called as the three-phase bidirectional controller. Let the load is star connected so at each phase there are antiparallel connected SCRs. ... conduct at the same time and the third phase will be open.

Description : Explain the operation of full bridge converters with their different operating modes. State its advantages and disadvantages.

Last Answer : Full bridge converter: Full bridge converter provides isolation between input and output. Full bridge converter is used for step up or step down the input voltage. Full bridge converter consists of four power semiconductor ... Require filter on both input and output.

Description : single phase full converter

Last Answer : single phase full converter

Description : The four-quadrant dual operation requires  (a) Two full converters in series  (b) Two full converters connected back to back  (c) Two full converters connected in parallel.  (d) Two semiconverters connected back to back

Last Answer : The four-quadrant dual operation requires Two full converters connected back to back 

Description : What would happen if a power transformer designed for operation on 50 Hz (frequency) were connected to a 500 Hz (frequency) source of the same voltage:  (A) Eddy Current and Hysteresis losses will be ... Current will be too much high  (C) Transformer may start to smoke and burn  (D) No effect

Last Answer : What would happen if a power transformer designed for operation on 50 Hz (frequency) were connected to a 500 Hz (frequency) source of the same voltage:  (A) Eddy Current and Hysteresis losses will be ... will be too much high  (C) Transformer may start to smoke and burn  (D) No effect

Description : Why would HD Access DTA 1030D stop working after a few hours?

Last Answer : I edited the title, (it was wouldn’t)

Description : How to Find a Four Leaf Clover

Last Answer : How to Find a Four Leaf Clover A four leaf clover is associated with good luck, particularly because it is rare and hard to find. A clover with four leaves is actually considered a genetic defect, ... it! You can learn more about preserving plants and flowers in this article: How to Dry Flowers.

Description : State any Four lE Rules regarding electric safety. 

Last Answer :  lE Rules regarding electric safety: 1. IE Rule 3 : Authorization 2. IE Rule 29 : Construction and maintenance of electrical supply line and apparatus 3. IE Rule 30: Service line and apparatus on ... 26. IE Rule 60: Test for resistance of insulation 27. IE Rule 61: Connection with earth 

Description : Explain any four properties of Moulding sand. 

Last Answer : 1. Porosity: Molten metal always contain a certain amount of dissolved gases, which are evolved when the metal freezes the molten metal coming in contact with the moist sand , generates steam or ... to the casting. Refractoriness is measured by the sinter point of the sand rather than its melting

Description : List any four casting defects.

Last Answer : The various types of casting defects are as follows: 1. Gas Porosity: Blowholes, open holes, pinholes. 2. Shrinkage defects: shrinkage cavity. 3. Mold material defects: Cut and washes, ... Pouring metal defects: Cold shut, misrun, slag inclusion. Metallurgical defects: Hot tears, hot spot.

Description : List any four materials used for pattern making

Last Answer : The various types of materials used are as follows: 1. Wood 2. Metal. 3. Plastic. 4. Plaster. 5. Wax.

Description : List any four accessories used on lathe.

Last Answer : The various accessories used in lathe are as follows. 1) Lathe centers 2) Carriers or driving dog 3) catch plates 4) Chucks 5) Face plates 6) Angle plates 7) Mandrels 8) Rests

Description : State any four advantages of LC filter.

Last Answer : 1. The choke input (LC) filter has a high output D.C voltage. 2. It has no loading effect on the rectifier and power transformer.  3. The diode does not have to carry surge currents.  ... effect on the rectifier and power transformer.  7. It has better voltage regulation than that of π filter.

Description : what is the difference between four point starter and three point starter?

Last Answer : The shunt connection in four point starter is provided separately form the line where as in three point starter it is connected with line which is the drawback in three point starter.

Description : Two 100W, 200V lamps are connected in series across a 200V supply. The total power consumed by each lamp will be in Watts

Last Answer : 4800

Last Answer : 1. Connected Load: It is the sum of load of all equipment's connected to supply system which are in use or not in use of each consumer. OR   The sum of connected load of all consumers ... is the maximum load which a consumer uses at a particular time period out of his total connected load. 

Description : Define the terms: i) Tariff ii) Fuel surcharge iii) Electricity Duty iv) Connected load

Last Answer : i) Tariff: The rate at which a consumer is charged for the consumption of electricity is called as tariff. OR The amount of money framed by the supplier for the supply of electrical energy ... is the total wattage of all appliances which are used by the consumer on his sanctioned connection. 

Description : Define the following terms related to tariff: (i) Connected load (ii) Unit consumed (iii) Fixed charges (iv) Electricity Tax 

Last Answer : (i) Connected load  It is the sum of the power ratings (Watts or kW or MW) of all devices and machines existing (installed) in the premises of consumer. It is used to decide the ... a percentage of the total electricity bill which includes all amounts that go to the electricity supply agency. 

Description : Define each of following terms: i) Connected load ii) Spinning reserve. 

Last Answer : i) Connected Load :- It is the sum of load of all equipment connected to supply system which are in use or not in use of each consumer. ii) Spinning Reserve:- It is reserved generating capacity in operation and connected to bus bar and ready to take a load.

Description :  A connected graph has ‘5’ number of branches and ‘4’ number of nodes. It's rank is A) 1 B) 2 C) 3 D) 4 

Last Answer :  A connected graph has ‘5’ number of branches and ‘4’ number of nodes. It's rank is 3 

Description : In an R-C phase shift oscillator, the minimum no. of R-C networks to be connected in cascade will be -

Last Answer : In an R-C phase shift oscillator, the minimum no. of R-C networks to be connected in cascade will be 3

Description : Three identical resistors connected in star consume 5000 W. If the resistors are connected in delta across the same supply, the power consumed will be

Last Answer : Three identical resistors connected in star consume 5000 W. If the resistors are connected in delta across the same supply, the power consumed will be 15000 W

Description : Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

Last Answer : Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

Description : When three resistors with unequal values are connected in parallel, _______ A) The current across the resistors is the same  B) The voltage drop across the resistors is the same C) The voltage drops across the resistors is proportional to the resistance of each resistor D) None of these

Last Answer : When three resistors with unequal values are connected in parallel, The voltage drop across the resistors is the same

Description : What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

Last Answer : What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

Description : The sequence components of current of a single-phase load connected to a 3-phase system are (A) equal positive and negative sequence components (B) equal positive, negative and zero sequence components (C) vector sum of sequence currents is zero (D) algebraic sum of sequence currents is zero

Last Answer : The sequence components of current of a single-phase load connected to a 3-phase system are equal positive, negative and zero sequence components

Description : If non-linear loads are connected to the power system, then (A) displacement power factor is same as the total power factor (B) displacement power factor is not equal to the total power ... factor is due to harmonic currents (D) total power factor is due to fundamental component of current

Last Answer : If non-linear loads are connected to the power system, then displacement power factor is not equal to the total power factor

Description :  With three resistances connected in parallel, if each dissipates 20 W the total power supplied by the voltage source equals?

Last Answer : Power is the only thing which is additive in both connection whether it is parallel or series connection so total power consumed will addition of all individual power =20+20+20 = 60 watt

Last Answer : If a D.C. motor is connected across the A.C. supply it will burn due to heat produced in the field winding by eddy currents.

Last Answer : A fuse is connected in series with circuit.

Description : Cells are connected in series in order to?

Last Answer : Cells are connected in series in order to increase voltage available.

Last Answer : For the parallel operation of two or more D.C. compound generators, we should ensure that series fields of all generators should be either on positive side or negative side of the armature.

Description : Fuel Pump Operation

Last Answer : Most people know that their cars have fuel pumps, but they don't really know how they operate. Some even pay attention to their fuel pumps only when they have already malfunctioned. It is important ... check your fuel pump for any problems because a defective pump can be dangerous while on the road.