8096 write-protected mode, no code can write to memory address between __. a) 2020 to 3FFFH b) 8000 to FFFFH c) 2000 to 3FFFH d) 2020 to 202FH 17. If the __ pin is ___ , then we have the option of using the ____ ROM or EPROM together with _____ memory and devices. a) EA, high, internal, external b) EA, low, internal, external c) EA, high, external, internal d) EA, low, external, internal

8096 write-protected mode, no code can write to memory address between __. a) 2020 to 3FFFH b) 8000 to FFFFH c) 2000 to 3FFFH d) 2020 to 202FH 17. If the __ pin is ___ , then we have the option of using the ____ ROM or EPROM together with _____ memory and devices.
a) EA, high, internal, external
b) EA, low, internal, external
c) EA, high, external, internal
d) EA, low, external, internal
by

1 Answer

Answer :

c) EA, high, external, internal
by

Related questions

8096 write-protected mode, no code can write to memory address between __. a) 2020 to 3FFFH b) 8000 to FFFFH c) 2000 to 3FFFH d) 2020 to 202FH

Description : 8096 write-protected mode, no code can write to memory address between __. a) 2020 to 3FFFH b) 8000 to FFFFH c) 2000 to 3FFFH d) 2020 to 202FH

Last Answer : c) 2000 to 3FFFH

If the __ pin is ___ , then we have the option of using the ____ ROM or EPROM together with _____ memory and devices. a) EA, high, internal, external b) EA, low, internal, external c) EA, high, external, internal d) EA, low, external, internal

Description : If the __ pin is ___ , then we have the option of using the ____ ROM or EPROM together with _____ memory and devices. a) EA, high, internal, external b) EA, low, internal, external c) EA, high, external, internal d) EA, low, external, internal

Last Answer : a) EA, high, internal, external

In 8096, CCB bit 3 is ____. a) write strobe mode select b) address valid strobe select c) bus width select d) Internal read control mode

Description : In 8096, CCB bit 3 is ____. a) write strobe mode select b) address valid strobe select c) bus width select d) Internal read control mode

Last Answer : c) bus width select

In 8096, CCB bit 3 is ____. a) write strobe mode select b) address valid strobe select c) bus width select d) Internal read control mode

Description : In 8096, CCB bit 3 is ____. a) write strobe mode select b) address valid strobe select c) bus width select d) Internal read control mode

Last Answer : b) address valid strobe select

In 8096, mode ____ of serial port are ___ modes commonly used for ____ communications. a) 1, 8bit, single processor b) 0, 7bit, multiple microcontroller c) 2, 9 bit, multiple processors d) 3, 8 bit, multiple microcontroller

Description : In 8096, mode ____ of serial port are ___ modes commonly used for ____ communications. a) 1, 8bit, single processor b) 0, 7bit, multiple microcontroller c) 2, 9 bit, multiple processors d) 3, 8 bit, multiple microcontroller

Last Answer : a) 1, 8bit, single processor

In 8096, mode ____ of serial port are ___ modes commonly used for ____ communications. a) 1, 8bit, single processor b) 0, 7bit, multiple microcontroller c) 2, 9 bit, multiple processors d) 3, 8 bit, multiple microcontroller

Description : In 8096, mode ____ of serial port are ___ modes commonly used for ____ communications. a) 1, 8bit, single processor b) 0, 7bit, multiple microcontroller c) 2, 9 bit, multiple processors d) 3, 8 bit, multiple microcontroller

Last Answer : c) 2, 9 bit, multiple processors

In 8051 an external interrupt 1 vector address is of ________ and causes of interrupt if ____. a) 000BH, a high to low transition on pin INT1 b) 001BH, a low to high transition on pin INT1 c) 0013H, a high to low transition on pin INT1 d) 0023H, a low to high transition on pin INT1

Description : In 8051 an external interrupt 1 vector address is of ________ and causes of interrupt if ____. a) 000BH, a high to low transition on pin INT1 b) 001BH, a low to high transition on pin INT1 c) 0013H, a high to low transition on pin INT1 d) 0023H, a low to high transition on pin INT1

Last Answer : a) 000BH, a high to low transition on pin INT1

Virtual Mode Flag bit can be set using ____ instruction or any task switch operation only in the _____ mode a) IRET, Virtual b) POPF, Real c) IRET, protected d) POPF, protected

Description : Virtual Mode Flag bit can be set using ____ instruction or any task switch operation only in the _____ mode a) IRET, Virtual b) POPF, Real c) IRET, protected d) POPF, protected

Last Answer : b) POPF, Real

Which of the following is form of semi conductor memory in which it is possible to change the contents of selected memory locations by applying suitable electrical signals? a. CAM b. ROM c. EPROM d. Abacus

Description : Which of the following is form of semi conductor memory in which it is possible to change the contents of selected memory locations by applying suitable electrical signals? a. CAM b. ROM c. EPROM d. Abacus

Last Answer : c. EPROM

____ causes the address of the next microprocessor to be obtained from the memory: a. CRJA b. ROM c. MAP d. HLT

Description : ____ causes the address of the next microprocessor to be obtained from the memory: a. CRJA b. ROM c. MAP d. HLT

Last Answer : c. MAP

Which of the following memories allows simultaneous read and write operations? a. ROM b. RAM c. EPROM d. None of above

Description : Which of the following memories allows simultaneous read and write operations? a. ROM b. RAM c. EPROM d. None of above

Last Answer : b. RAM

8096 has ___ general purpose I/O ports, Port 2 includes ______ of the following i) two quasi-bidirectional I/O lines ii) two output lines iii) four input lines iv) open drain outputs a) 4, i, iv b) 6, ii, iii c) 4, i,ii,iii d) 6, i, ii, iv

Description : 8096 has ___ general purpose I/O ports, Port 2 includes ______ of the following i) two quasi-bidirectional I/O lines ii) two output lines iii) four input lines iv) open drain outputs a) 4, i, iv b) 6, ii, iii c) 4, i,ii,iii d) 6, i, ii, iv

Last Answer : c) 4, i,ii,iii

Intel 8096 is of ___ bit microcontroller family called as ______. a) 8, MCS51 b) 16, MCS51 c) 8, MCS96 d) 16, MCS96

Description : Intel 8096 is of ___ bit microcontroller family called as ______. a) 8, MCS51 b) 16, MCS51 c) 8, MCS96 d) 16, MCS96

Last Answer : d) 16, MCS96

8096 has ___ general purpose I/O ports, Port 2 includes ______ of the following i) two quasi-bidirectional I/O lines ii) two output lines iii) four input lines iv) open drain outputs a) 4, i, iv b) 6, ii, iii c) 4, i,ii,iii d) 6, i, ii, iv

Description : 8096 has ___ general purpose I/O ports, Port 2 includes ______ of the following i) two quasi-bidirectional I/O lines ii) two output lines iii) four input lines iv) open drain outputs a) 4, i, iv b) 6, ii, iii c) 4, i,ii,iii d) 6, i, ii, iv

Last Answer : c) 4, i,ii,iii

Intel 8096 is of ___ bit microcontroller family called as ______. a) 8, MCS51 b) 16, MCS51 c) 8, MCS96 d) 16, MCS96

Description : Intel 8096 is of ___ bit microcontroller family called as ______. a) 8, MCS51 b) 16, MCS51 c) 8, MCS96 d) 16, MCS96

Last Answer : d) 16, MCS96

In 8279, a scanned sensor matrix mode, if a sensor changes its state, the ___ line goes ____ to interrupt the CPU. a) CS, high b) A0, high c) IRQ, high d) STB, high

Description : In 8279, a scanned sensor matrix mode, if a sensor changes its state, the ___ line goes ____ to interrupt the CPU. a) CS, high b) A0, high c) IRQ, high d) STB, high

Last Answer : c) IRQ, high

Customized ROMS are called: a. Mask ROM b. Flash ROM c. EPROM d. None of these

Description : Customized ROMS are called: a. Mask ROM b. Flash ROM c. EPROM d. None of these

Last Answer : a. Mask ROM

Which pin of port 3 is has an alternative function as write control signal for external data memory? a) P3.8 b) P3.3 c) P3.6 d) P3.1

Description : Which pin of port 3 is has an alternative function as write control signal for external data memory? a) P3.8 b) P3.3 c) P3.6 d) P3.1

Last Answer : d) P3.1

Which pin of port 3 is has an alternative function as write control signal for external data memory? a) P3.8 b) P3.3 c) P3.6 d) P3.1

Description : Which pin of port 3 is has an alternative function as write control signal for external data memory? a) P3.8 b) P3.3 c) P3.6 d) P3.1

Last Answer : c) P3.6

8096 has following features fill up the following, i) ____ Register file, ii) ____ I/O Ports iii) ____ architecture. a) 256 byte, five 8bit, register to register b) 256 byte, four 8bit, register to register c) 232 byte, five 8bit, register to register d) 232 byte, six 8 bit, register to register

Description : 8096 has following features fill up the following, i) ____ Register file, ii) ____ I/O Ports iii) ____ architecture. a) 256 byte, five 8bit, register to register b) 256 byte, four 8bit, register ... c) 232 byte, five 8bit, register to register d) 232 byte, six 8 bit, register to register

Last Answer : c) 232 byte, five 8bit, register to register

8096 has following features fill up the following, i) ____ Register file, ii) ____ I/O Ports iii) ____ architecture. a) 256 byte, five 8bit, register to register b) 256 byte, four 8bit, register to register c) 232 byte, five 8bit, register to register d) 232 byte, six 8 bit, register to register

Description : 8096 has following features fill up the following, i) ____ Register file, ii) ____ I/O Ports iii) ____ architecture. a) 256 byte, five 8bit, register to register b) 256 byte, four 8bit, ... c) 232 byte, five 8bit, register to register d) 232 byte, six 8 bit, register to register

Last Answer : d) 232 byte, six 8 bit, register to register

Which of the following statements on DRAM are correct? i) Page mode read operation is faster than RAS read. ii) RAS input remains active during column address strobe. iii) The row and column addresses are strobed into the internal buffers using RAS and CAS inputs respectively. a) i & iii b) i & ii c) all d) iii

Description : Which of the following statements on DRAM are correct? i) Page mode read operation is faster than RAS read. ii) RAS input remains active during column address strobe. iii) The row and column addresses are strobed into the ... RAS and CAS inputs respectively. a) i & iii b) i & ii c) all d) iii

Last Answer : d) iii

A memory that is capable of determining whether a given datum is contained in one of its address is a. ROM b. PROM c. CAM d. RAM

Description : A memory that is capable of determining whether a given datum is contained in one of its address is a. ROM b. PROM c. CAM d. RAM

Last Answer : c. CAM

In 8255, under the I/O mode of operation we have __ modes. Under which mode will have the following features i) A 5 bit control port is available. ii) Three I/O lines are available at Port C. a) 3, Mode2 b) 2, Mode 2 c) 4, Mode 3 d) 3, Mode 2

Description : In 8255, under the I/O mode of operation we have __ modes. Under which mode will have the following features i) A 5 bit control port is available. ii) Three I/O lines are available at Port C. a) 3, Mode2 b) 2, Mode 2 c) 4, Mode 3 d) 3, Mode 2

Last Answer : a) 3, Mode2

How many address lines in a 4096 x 8 EPROM CHIP?

Description : How many address lines in a 4096 x 8 EPROM CHIP?

Last Answer : 12 address lines.

A___ on this pin indicates a memory operation: a. Low b. High c. Medium d. None of these

Description : A___ on this pin indicates a memory operation: a. Low b. High c. Medium d. None of these

Last Answer : a. Low

CPU performs read/write operations at any point in time in _____ A. PROM B. EPROM C. RAM D. ROM

Description : CPU performs read/write operations at any point in time in _____ A. PROM B. EPROM C. RAM D. ROM

Last Answer : B. EPROM

The memory which is programmed at the time it is manufactured a. POM b. RAM c. PROM d. EPROM

Description : The memory which is programmed at the time it is manufactured a. POM b. RAM c. PROM d. EPROM

Last Answer : a. POM

which chips using special external equipment can reprogram a. ROM b. PROM c. SAM d. RAM

Description : which chips using special external equipment can reprogram a. ROM b. PROM c. SAM d. RAM

Last Answer : b. PROM

__ bit in ICW1 indicates whether the 8259A is cascade mode or not? a) LTIM=0 b) LTIM=1 c) SNGL=0 d) SNGL=1

Description : __ bit in ICW1 indicates whether the 8259A is cascade mode or not? a) LTIM=0 b) LTIM=1 c) SNGL=0 d) SNGL=1

Last Answer : c) SNGL=0

In 8096 we have _____interrupt sources and _______ interrupt vectors. a) 18, 8 b) 21, 6 c) 21, 8 d) 16, 8

Description : In 8096 we have _____interrupt sources and _______ interrupt vectors. a) 18, 8 b) 21, 6 c) 21, 8 d) 16, 8

Last Answer : c) 21, 8

In 8096 we have _____interrupt sources and _______ interrupt vectors. a) 18, 8 b) 21, 6 c) 21, 8 d) 16, 8

Description : In 8096 we have _____interrupt sources and _______ interrupt vectors. a) 18, 8 b) 21, 6 c) 21, 8 d) 16, 8

Last Answer : c) 21,

In modes 2 and 3, if _____ bit of SCON bit is set will causes enable multiprocessor communication and is of ____ bit address. a) SM1, 9EH b) TB8 , 9CH c) SM2 , 9DH d) SM0, 9FH

Description : In modes 2 and 3, if _____ bit of SCON bit is set will causes enable multiprocessor communication and is of ____ bit address. a) SM1, 9EH b) TB8 , 9CH c) SM2 , 9DH d) SM0, 9FH

Last Answer : c) SM2 , 9DH

A type of core store that has a lower access time than the devices used for working store in the same processor is known as a. Core memory b. Buffer c. Fast core d. Address register

Description : A type of core store that has a lower access time than the devices used for working store in the same processor is known as a. Core memory b. Buffer c. Fast core d. Address register

Last Answer : d. Address register

The CPU removes the ___ signal to complete the memory write operation: a. Read b. Write c. Both A and B d. None of these

Description : The CPU removes the ___ signal to complete the memory write operation: a. Read b. Write c. Both A and B d. None of these

Last Answer : a. Read

In 8279 Strobed input mode, the control line goes low. The data on return lines is strobed in the ____. a) FIFO byte by byte b) FILO byte by byte c) LIFO byte by byte d) LILO byte by byte.

Description : In 8279 Strobed input mode, the control line goes low. The data on return lines is strobed in the ____. a) FIFO byte by byte b) FILO byte by byte c) LIFO byte by byte d) LILO byte by byte.

Last Answer : a) FIFO byte by byte

How many synchronous and asynchronous modes are there in serial port of 8096? M. Krishna Kumar/IISc. Bangalore M5/V1/June 04/1 Microprocessors and Microcontrollers/ Multiple Choice Questions Architecture of Micro controllers a) 2, 2 respectively b) 3,1 respectively c) 1, 3 respectively d) 1, 2 respectively

Description : How many synchronous and asynchronous modes are there in serial port of 8096? M. Krishna Kumar/IISc. Bangalore M5/V1/June 04/1 Microprocessors and Microcontrollers/ Multiple Choice Questions Architecture of Micro ... 2, 2 respectively b) 3,1 respectively c) 1, 3 respectively d) 1, 2 respectively

Last Answer : c) 1, 3 respectively

The memory which is programmed at the time it is manufactured A) ROM B) RAM C) PROM D) EPROM

Description : The memory which is programmed at the time it is manufactured A) ROM B) RAM C) PROM D) EPROM

Last Answer : Answer : C

Which of the following is form of semi conductor memory in which it is possible to change the contents of selected memory locations by applying suitable electrical signals? a. CAM b. ROM c. EPROM d. Abacus

Description : Which of the following is form of semi conductor memory in which it is possible to change the contents of selected memory locations by applying suitable electrical signals? a. CAM b. ROM c. EPROM d. Abacus

Last Answer : EPROM

Which of the following is form of semi conductor memory in which it is possible to change the contents of selected memory locations by applying suitable electrical signals? a. CAM b. ROM c. EPROM d. Abacus

Description : Which of the following is form of semi conductor memory in which it is possible to change the contents of selected memory locations by applying suitable electrical signals? a. CAM b. ROM c. EPROM d. Abacus

Last Answer : c. EPROM

Because we wish to allow each ASCII code to occupy one location in memory, most memories are _____ addressable. a. BYTE b. NIBBLE c. WORD (16 bits) d. DOUBLEWORD (32 bits)

Description : Because we wish to allow each ASCII code to occupy one location in memory, most memories are _____ addressable. a. BYTE b. NIBBLE c. WORD (16 bits) d. DOUBLEWORD (32 bits)

Last Answer : a. BYTE

The external device is connected to a pin called the ______ pin on the processor chip. a. Interrupt b. Transfer c. Both d. None of these

Description : The external device is connected to a pin called the ______ pin on the processor chip. a. Interrupt b. Transfer c. Both d. None of these

Last Answer : a. Interrupt

Pentium Pro can address _____ of memory: a. 4 GB b. 128 GB c. 256 GB d. 512 GB

Description : Pentium Pro can address _____ of memory: a. 4 GB b. 128 GB c. 256 GB d. 512 GB

Last Answer : a. 4 GB

By whom address of external function in the assembly source file supplied by __ when activated: a. Assembler b. Linker c. Machine d. Code

Description : By whom address of external function in the assembly source file supplied by __ when activated: a. Assembler b. Linker c. Machine d. Code

Last Answer : b. Linker

If ______input pin of 80386 if activated, allows address pipelining during 80386 bus cycles. a) BS16 b) NA c) PEREQ d) ADS

Description : If ______input pin of 80386 if activated, allows address pipelining during 80386 bus cycles. a) BS16 b) NA c) PEREQ d) ADS

Last Answer : a) BS16

Instructions and memory address are represented by a. Character code b. Binary codes c. Binary word d. Parity bit

Description : Instructions and memory address are represented by a. Character code b. Binary codes c. Binary word d. Parity bit

Last Answer : b. Binary codes

CD-ROM a. Is a `semiconductor memory b. Memory register c. Magnetic memory d. None of the above

Description : CD-ROM a. Is a `semiconductor memory b. Memory register c. Magnetic memory d. None of the above

Last Answer : d. None of the above

Which is the type of memory for information that does not change on your computer? a. RAM b. ROM c. ERAM d. RW / RAM

Description : Which is the type of memory for information that does not change on your computer? a. RAM b. ROM c. ERAM d. RW / RAM

Last Answer : b. ROM

The instructions for starting the computer are house on a. Random access memory b. CD-Rom c. Read only memory chip

Description : The instructions for starting the computer are house on a. Random access memory b. CD-Rom c. Read only memory chip

Last Answer : c. Read only memory chip

The two kinds of main memory are: a. Primary and secondary b. Random and sequential c. ROM and RAM d. All of above

Description : The two kinds of main memory are: a. Primary and secondary b. Random and sequential c. ROM and RAM d. All of above

Last Answer : c. ROM and RAM