If the % reactance upto the fault point is 20%, then the short circuit current will be

1 Answer

Answer :

If the % reactance upto the fault point is 20%, then the short circuit current will be 5 times the full load current

Related questions

Description : In which fault the maximum short circuit current occurs?

Last Answer : In three phase bolted fault the maximum short circuit occurs.

Last Answer : Reactance relay is preferred for phase fault on short transmission line.

Description : The armature current on symmetrical 3 phase short circuit of a synchronous machine (salient pole)  (A) has q -axis current only (B) has d -axis current only (C) has both d and q axis currents (D) cannot be divided between q and d axis currents

Last Answer : The armature current on symmetrical 3 phase short circuit of a synchronous machine (salient pole) has d -axis current only

Description : If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug setting multiplier will be

Last Answer : If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug setting multiplier will be 10

Last Answer : The inverse definite mean time relays are used for over current and earth fault protection of transformer against internal short-circuits.

Description : The operating point of a protective current transformer is near the

Last Answer : The operating point of a protective current transformer is near the Ankle point

Last Answer : The short circuit in any winding of the transformer is the result of impulse voltage.

Description : If the fault current is 2000 A, the relay setting is 50% and CT ratio is 400:5, the plug setting multiplier will be

Last Answer : If the fault current is 2000 A, the relay setting is 50% and CT ratio is 400:5, the plug setting multiplier will be 10 A

Description : A charge of 0.1 C moves past a given point every 0.01 s. How much is the current?

Last Answer : The current is 10.0A.  1ampere = 1 Coulomb per 1 second.  0.1Coulombs ÷ 0.01seconds = 10.0amperes.

Description : Describe the difference between an open circuit and a short circuit.

Last Answer : Open circuit means the wire is cut meaning power will not flow and close circuit means wire is not cut and hence power will flow.Short circuit is the same as close circuit

Description : Which of the following are known as the short circuit parameters of a 2- port network? (A) Z- parameters. (B) H- parameters. (C) Y- parameters. (D) A,B,C,D, parameters.

Last Answer : Which of the following are known as the short circuit parameters of a 2- port network? (A) Z- parameters. (B) H- parameters. (C) Y- parameters. (D) A,B,C,D, parameters.

Last Answer : Short circuit test on transformers is conducted to determine copper losses.

Last Answer : In short circuit test of transformer the low voltage side is short circuited . On high voltage side the voltmeter is connected in parallel and ammeter in series and also a wattmeter is ... circuit test is done for determining impedance and losses. In this test iron losses is neglected.

Description : Reactance relay is normally preferred for protection against

Last Answer : Reactance relay is normally preferred for protection against earth faults

Description : With fault clearing time, the transient stability of a power system

Last Answer : With fault clearing time, the transient stability of a power system decreases

Description : To protect the power transformer (Y-Y with neutral grounded) against fault, what type of connection do the CTs have ?

Last Answer : To protect the power transformer (Y-Y with neutral grounded) against fault, what type of connection do the CTs have ? Δ-Δ connection

Last Answer : Fault diverters are basically fast switches.

Description : Which is the most common type of fault?

Last Answer : Single phase to ground fault is the most common type of fault.

Description : In a series R-C circuit, with the increase in frequency, current (A) Reduces (B) Increases (C) Does not change (D) Becomes zero

Last Answer : In a series R-C circuit, with the increase in frequency, current Increases

Description : In parallel RLC resonance circuit at resonance the current will be  (1) Minimum (2) Maximum (3) Zero (4) Infinite

Last Answer : In parallel RLC resonance circuit at resonance the current will be Minimum 

Description : In a series RLC high Q circuit, the current peaks at a frequency  (1) equal to the resonant frequency (2) greater than the resonant frequency (3) less than the resonant frequency (4) equal to half the resonant frequency

Last Answer : In a series RLC high Q circuit, the current peaks at a frequency equal to the resonant frequency

Description : When one leg of parallel circuit is opened out the total current will?

Last Answer : When one leg of parallel circuit is opened out the total current will decrease.

Description : Electric current passing through the circuit produces?

Last Answer : Electric current passing through the circuit produces thermal effect.

Description : Magnitude of current at resonance in R-L-C circuit?

Last Answer : The current will be maximum if it is a series rlc circuit.

Description : In a loss-free R-L-C circuit the transient current is?

Last Answer : In a loss-free R-L-C circuit the transient current is sinusoidal.

Description : What is the direction of flow of electric current in an electric circuit?

Last Answer : It  flows  from  anode  to  cathode  (direction  of   holes  flow)

Description : Blind spot is a point in the zones of protection where

Last Answer : Blind spot is a point in the zones of protection where No protection is available.

Description : Define impedance diagram and reactance diagram.

Last Answer : Impedance diagram: Impedance diagram is the simplified equivalent circuits of single line or one line diagrams of power system in which all components are represented by their equivalent circuit.  ... machines are neglected and is used only for fault current calculation is called reactance diagram.

Description : What do you mean by exciting resistance and exciting reactance?

Last Answer : At no-load, a transformer behaves as a highly inductive load connected to the system which contains some resistance and inductance in parallel. The resistance is called exciting resistance R0 = V1/I w and reactance is called exciting reactance, X0 = V1/I mag

Description : Capacitive reactance

Last Answer : Capacitive reactance formula

Description : Parallel Reactance and Resistance Example 1

Last Answer : Parallel Reactance and Resistance Example 1

Description : AC Circuits with Resistance but No Reactance

Last Answer : AC Circuits with Resistance but No Reactance AC Circuits with Resistance but No Reactance Series resistances let two resistances R 1 and R 2 are connected in series as shows in figure and there ... voltage. Voltage V A is common to both the branch hence voltage V A is common reference.

Description : A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage regulation at 0.8 pf lagging would he

Last Answer : A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage regulation at 0.8 pf lagging would he 0.52

Description : Consider the following statements. Which of these statements are correct ?  (1) Reactance relays are preferred for ground fault relaying  (2) Impedance relays are most suitable for:protecting long transmission lines  (3) Mho relays are best ... (1) and (3) (C) (2) and (4) (D) (1), (2) and (4)

Last Answer : Consider the following statements. Which of these statements are correct ?  (1) Reactance relays are preferred for ground fault relaying  (2) Impedance relays are most suitable for:protecting long transmission lines  (3) Mho relays are ... (1) and (3) (C) (2) and (4) (D) (1), (2) and (4)

Description : Ratio of the rotor reactance X to the rotor resistance R for a two-phase servo motor (A) is equal to that of a normal induction motor (B) is less than that of a normal induction motor (C) ... than that of a normal induction motor (D) may be less or greater than that of a normal induction motor

Last Answer : C

Description : A 4000 kVA, 11 kV/132 kV delta-star connected 3-phase transformer has reactance, x1 = 0.12 p.u. The actual value of x1 referred to the low voltage side is (A) 0.85 Ω (B) 3.63 Ω (C) 36.3 Ω (D) 252 Ω

Last Answer : A 4000 kVA, 11 kV/132 kV delta-star connected 3-phase transformer has reactance, x1 = 0.12 p.u. The actual value of x1 referred to the low voltage side is 3.63 Ω

Description : A reactance relay is (A) Voltage restrained directional relay (B) Directional restrained over-current relay (C) Voltage restrained over current relay (D) Directional restrained over voltage relay

Last Answer : A reactance relay is Directional restrained over-current relay

Description : Capacitive reactance is more when?

Last Answer : Capacitive reactance is more when capacitance is less and frequency of supply is less.

Description : What is the unit of reactance?

Last Answer : Unit of reactance is Ohms ( Ω ) .Reactance is denoted by X .

Description : What is the inverse of reactance?

Last Answer : Inverse of reactance is Susceptance .Unit of Susceptance is Siemens.

Description : what is the reciprocal of reactance?

Last Answer : reciprocal of reactance is susceptance.

Description : Give the causes and impact and reasons of grid system fault. 

Last Answer : Following are the causes/reasons grid system fault: 1. Major imbalance between generation and consumption i.e. demand is more than generation. 2. Low frequency, due to some faults the frequency ... of supply and causes inconvenience to people. 6. Disturb the routine work of common all people.

Description : If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded transformer, then  (A) zero sequence currents are present on both sides of the transformer  (B) ... side  (D) zero sequence currents are present on the primary side but not on the secondary side

Last Answer : If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded transformer, then zero sequence currents are absent on both sides of the transformer 

Description : A shunt fault is characterized by (A) Increase in current, frequency and pf (B) Increase in current, reduction in frequency and pf (C) Increase in current and frequency, reduction in pf (D) Decrease in current and frequency

Last Answer : B

Description : In the induction type directional over current relay, when a short-circuit occurs in the circuit (A) power flows in reverse direction (B) power flows in normal direction (C) directional power element does not operate (D) over current element is not energized

Last Answer : In the induction type directional over current relay, when a short-circuit occurs in the circuit power flows in reverse direction

Description : Single point Cutting tool signature

Last Answer : The shape of a tool is specified in a special sequence and this special sequence is called tool signature. The tool signature is given below (i) Back rake angle (ii) Side rake angle (iii) ... rake, end relief, side relief, end cutting edge, side cutting edge angle and 0.8 mm nose radius.

Description : Illustrate with neat wiring diagram a single lamp control by two point method.

Last Answer : Single lamp control by two point method:  This system is commonly used for stair case wiring. It consists of two way switches (the switch operates always in one of the two possible positions) the ... the person will change the position of switch S2, so that the lamp will be switched OFF'.

Last Answer : Three point starter can be used for both shunt and compound motor.