Two 100W, 200V lamps are connected in series across a 200V supply. The total power consumed by each lamp will be in Watts

2 Answers

Answer :

Two 100W, 200V lamps are connected in series across a 200V supply. The total power consumed by each lamp will be in Watts 25 Watts

Answer :

4800

Related questions

Description : What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

Last Answer : What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

Description : Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

Last Answer : Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

Description : We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be

Last Answer : We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be 2.4 kOhm

Description : Cells are connected in series in order to?

Last Answer : Cells are connected in series in order to increase voltage available.

Last Answer : If a D.C. series motor is operated on A.C. supply, it will spark excessively, have poor efficiency, have poor power factor.

Description : The total power of an AM transmitter having a carrier power of 50 W and the percentage of modulation at 80% is A) 50 W B) 66 W C) 68 W D) 70 W 

Last Answer : The total power of an AM transmitter having a carrier power of 50 W and the percentage of modulation at 80% is 66 W

Last Answer : When a D.C. series motor is connected to A.C. supply, the power factor will be low because of high inductance of field and armature circuits.

Description : What is need of regulated power supply?

Last Answer : A regulated power supply is used to ensure that the output remains constant even if the input changes. But sometimes main supply voltage, load, and surrounding temperature keep changing and altering the ... power supply is needed that will accept an AC input and give a constant DC output.

Description : If non-linear loads are connected to the power system, then (A) displacement power factor is same as the total power factor (B) displacement power factor is not equal to the total power ... factor is due to harmonic currents (D) total power factor is due to fundamental component of current

Last Answer : If non-linear loads are connected to the power system, then displacement power factor is not equal to the total power factor

Description : Draw the block diagram of regulated power supply, explain function of each block and draw waveforms of each stage.

Last Answer : 1. A step down transformer 2. A rectifier 3. A filter 4. A regulator Operation of Regulated Power Supply:- Step Down Transformer:- A step down transformer will ... regulator. A regulator will maintain the output constant even when changes at the input or any other changes occur.

Description : What is the Power Supply specification for 8085AH microprocessor? A) Single +5V supply with 10% voltage margins B) Dual +5V supply with 10% voltage margins C) Single +10V supply with 5% voltage margins D) Dual +5V supply with 5% voltage margins 

Last Answer : What is the Power Supply specification for 8085AH microprocessor? A) Single +5V supply with 10% voltage margins B) Dual +5V supply with 10% voltage margins C) Single +10V supply with 5% voltage margins D) Dual +5V supply with 5% voltage margins 

Description : The time period of third harmonic of power supply frequency, in milliseconds, is (A) 20 (B) 3.33 (C) 6.66 (D) 60

Last Answer : The time period of third harmonic of power supply frequency, in milliseconds, is 6.66 

Last Answer : Overhead lines for power supply to tramcars are at a minimum height of 10 m.

Last Answer : The primary reason for low power factor is supply system is due to installation of induction motors.

Last Answer : For high value of diversity factor, a power station of given installed capacity will be in a position to supply more number of consumers.

Last Answer : Rectifier is use in power supply to convert Alternating current (AC) to Direct Current (DC) .

Description :  An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to a load impedance ZL when A) ZL = R B) ZL = jXS C) ZL = R-jXS D) ZL = R+jXS 

Last Answer :  An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to a load impedance ZL when ZL = R-jXS

Last Answer : If a D.C. motor is connected across the A.C. supply it will burn due to heat produced in the field winding by eddy currents.

Description : Write various advantages of using high mast tower lighting viz a vIz Sodium lamps in circulating areas?

Last Answer : Ans. (i) Better illumination (ii) Vide area illumination (iii)where mass public movement (iv) Where loading & unloading of materials (v) At goods coaches & passenger coaches formation, checking and maintenance.

Description : Ceiling lamps. What are they and how to choose?

Last Answer : Well-chosen lighting can stimulate productive activities and can create an intimate and relaxing atmosphere. The variety of ceiling lights is not limited to traditional center chandeliers. In addition ... Their placement along the perimeter of the bathroom will visually make the room more spacious.

Description : What are the advantages of LED lamps?

Last Answer : What are the advantages of LED lamps? LED lamps have an advantage over fluorescent lamps in the first place in terms of environmental friendliness. Another reason for using LED lamps is ... advantages. Today, such lamps are used in everyday life, for industrial lighting and street lighting.

Description : What kind of lamps are there and how to make the right choice?

Last Answer : What kind of lamps are there and how to make the right choice? Which of the lamps in the store should you choose? Having solved several tasks at once to illuminate the room and create coziness? ... in the room. And, familiar to everyone, fluorescent lamps can create the illusion of a sunny day.

Description : Compare the AC and DC Arc lamps.

Last Answer : AC Arc Lamp DC Arc Lamp Cross section area of electrode is same Cross section area of electrode is positive rod is twice that of negative rod Series inductor is used for stability ... supply is used for DC arc lamp Luminous efficiency is less Luminous efficiency is high

Description : Choose the correct order of electric discharge lamps in their increasing order of efficiencies (lumens/watt) :  (A) Sodium vapour lamp, Mercury vapour lamp, Neon lamp  (B) Neon lamp, Sodium vapour ... Mercury vapour lamp, Sodium vapour lamp  (D) Mercury vapour lamp, Sodium vapour lamp, Neon lamp

Last Answer : Choose the correct order of electric discharge lamps in their increasing order of efficiencies (lumens/watt) :  (A) Sodium vapour lamp, Mercury vapour lamp, Neon lamp  (B) Neon lamp, Sodium ... Mercury vapour lamp, Sodium vapour lamp  (D) Mercury vapour lamp, Sodium vapour lamp, Neon lamp

Description : How to find total impedance Z, current I and Impedance angle ?

Last Answer : How to find total impedance Z, current I and Impedance angle ?

Description : What will happen if the primary of a transformer is connected to D.C. supply?  (A) Transformer will operate with low efficiency (B) Transformer will operate with high efficiency (C) No effect (D) Transformer may start to smoke and burn 

Last Answer : What will happen if the primary of a transformer is connected to D.C. supply?  (A) Transformer will operate with low efficiency (B) Transformer will operate with high efficiency (C) No effect (D) Transformer may start to smoke and burn 

Description : Total instantaneous power supplied by a 3-phase ac supply to a balanced R-L load is

Last Answer : Total instantaneous power supplied by a 3-phase ac supply to a balanced R-L load is constant

Description : Two resistances Rl and Ri are connected in series across the voltage source where Rl>Ri. The largest drop will be across?

Last Answer : Two resistances Rl and Ri are connected in series across the voltage source where Rl>Ri. The largest drop will be across Rl.

Description : A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the

Last Answer : A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the C only

Description : Define each of following terms: i) Connected load ii) Spinning reserve. 

Last Answer : i) Connected Load :- It is the sum of load of all equipment connected to supply system which are in use or not in use of each consumer. ii) Spinning Reserve:- It is reserved generating capacity in operation and connected to bus bar and ready to take a load.

Description :  A connected graph has ‘5’ number of branches and ‘4’ number of nodes. It's rank is A) 1 B) 2 C) 3 D) 4 

Last Answer :  A connected graph has ‘5’ number of branches and ‘4’ number of nodes. It's rank is 3 

Description : In an R-C phase shift oscillator, the minimum no. of R-C networks to be connected in cascade will be -

Last Answer : In an R-C phase shift oscillator, the minimum no. of R-C networks to be connected in cascade will be 3

Description : Three identical resistors connected in star consume 5000 W. If the resistors are connected in delta across the same supply, the power consumed will be

Last Answer : Three identical resistors connected in star consume 5000 W. If the resistors are connected in delta across the same supply, the power consumed will be 15000 W

Description : When three resistors with unequal values are connected in parallel, _______ A) The current across the resistors is the same  B) The voltage drop across the resistors is the same C) The voltage drops across the resistors is proportional to the resistance of each resistor D) None of these

Last Answer : When three resistors with unequal values are connected in parallel, The voltage drop across the resistors is the same

Description : Two bulbs of 100w and 40w respectively are connected in series across a 230v supply which bulb will glow bright and why?

Last Answer : A:Since two bulbs are in series they will get equal amount of electrical current but as the supply voltage is constant across the bulb(P=V^2/R).So the resistance of 40W bulb is greater and voltage across 40W is more (V=IR) so 40W bulb will glow brighter.

Description : Two bulbs of 100w and 40w respectively connected in series across a 230v supply which bulb will glow bright and why?

Last Answer : Since two bulbs are in series they will get equal amount of electrical current but as the supply voltage is constant across the Bulb (P=V^2/R).So the resistance of 40W bulb is greater and voltage across 40W is more (V=IR) so 40W bulb will glow brighter.

Description : What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

Last Answer : What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

Description : A lamp of 100W at 200V is supplied current at 100 volts. It will be equivalent to the lamp of:   a. 50W b. 40W c. 25W d. 10W 

Last Answer : A lamp of 100W at 200V is supplied current at 100 volts. It will be equivalent to the lamp of: 25W

Description : what is equivalent resistance when four 4 Ohm resistors are connected in i) series ii) parallel

Last Answer : equivalent resistance

Description : Consider a circuit with four resistors in series connected to a voltage source. What happens to the voltage across each resistor, if the value of each of the resistors is doubled? A) It will double B) It will remain the same C) It will be halved D) It will become zero

Last Answer : Consider a circuit with four resistors in series connected to a voltage source. What happens to the voltage across each resistor, if the value of each of the resistors is doubled? A) It will double B) It will remain the same C) It will be halved D) It will become zero

Description : In a three-phase supply floating neutral is undesirable because it way give rise to?

Last Answer : In a three-phase supply floating neutral is undesirable because it way give rise to unequal line voltages across the load.

Description : The effective resistance of an iron-cored choke working on ordinary supply frequency is more than its true resistance because of?

Last Answer : The effective resistance of an iron-cored choke working on ordinary supply frequency is more than its true resistance because of iron loss in core.

Description : Why does a transformer only work with an AC supply?

Last Answer : The transformer work depends on the induction as main principle ,for that AC is the right means

Description : A four -quadrant operation requires two full converters connected in  (1) Series (3) Back to back (2) Parallel (4) Series Cascade

Last Answer : A four-quadrant operation requires two full converters connected in Parallel 

Last Answer : 1. Connected Load: It is the sum of load of all equipment's connected to supply system which are in use or not in use of each consumer. OR   The sum of connected load of all consumers ... is the maximum load which a consumer uses at a particular time period out of his total connected load. 

Description : Define the terms: i) Tariff ii) Fuel surcharge iii) Electricity Duty iv) Connected load

Last Answer : i) Tariff: The rate at which a consumer is charged for the consumption of electricity is called as tariff. OR The amount of money framed by the supplier for the supply of electrical energy ... is the total wattage of all appliances which are used by the consumer on his sanctioned connection. 

Description : Define the following terms related to tariff: (i) Connected load (ii) Unit consumed (iii) Fixed charges (iv) Electricity Tax 

Last Answer : (i) Connected load  It is the sum of the power ratings (Watts or kW or MW) of all devices and machines existing (installed) in the premises of consumer. It is used to decide the ... a percentage of the total electricity bill which includes all amounts that go to the electricity supply agency. 

Description : The sequence components of current of a single-phase load connected to a 3-phase system are (A) equal positive and negative sequence components (B) equal positive, negative and zero sequence components (C) vector sum of sequence currents is zero (D) algebraic sum of sequence currents is zero

Last Answer : The sequence components of current of a single-phase load connected to a 3-phase system are equal positive, negative and zero sequence components

Description :  With three resistances connected in parallel, if each dissipates 20 W the total power supplied by the voltage source equals?

Last Answer : Power is the only thing which is additive in both connection whether it is parallel or series connection so total power consumed will addition of all individual power =20+20+20 = 60 watt

Last Answer : A fuse is connected in series with circuit.