If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug

If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug setting multiplier will be
by

1 Answer

Answer :

If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug setting multiplier will be 10

by

Related questions

If the fault current is 2000 A, the relay setting is 50% and CT ratio is 400:5, the plug setting multiplier will be

Description : If the fault current is 2000 A, the relay setting is 50% and CT ratio is 400:5, the plug setting multiplier will be

Last Answer : If the fault current is 2000 A, the relay setting is 50% and CT ratio is 400:5, the plug setting multiplier will be 10 A

If the % reactance upto the fault point is 20%, then the short circuit current will be

Description : If the % reactance upto the fault point is 20%, then the short circuit current will be

Last Answer : If the % reactance upto the fault point is 20%, then the short circuit current will be 5 times the full load current

The inverse definite mean time relays are used for over current and earth fault protection of transformer against?

Last Answer : The inverse definite mean time relays are used for over current and earth fault protection of transformer against internal short-circuits.

In which fault the maximum short circuit current occurs?

Description : In which fault the maximum short circuit current occurs?

Last Answer : In three phase bolted fault the maximum short circuit occurs.

A relay has a rating of 5 A, 2.2 sec IDMT and a relay setting of 125% TMS = 0.6. It is connected to a supply

Description : A relay has a rating of 5 A, 2.2 sec IDMT and a relay setting of 125% TMS = 0.6. It is connected to a supply circuit through a C.T. 400/5 ratio. The fault current is 4000 A. The operating current of the relay is

Last Answer : A relay has a rating of 5 A, 2.2 sec IDMT and a relay setting of 125% TMS = 0.6. It is connected to a supply circuit through a C.T. 400/5 ratio. The fault current is 4000 A. The operating current of the relay is 6.25A

Which relay is preferred for phase fault on short transmission line?

Last Answer : Reactance relay is preferred for phase fault on short transmission line.

Current ratio

Description : Current ratio

Last Answer : Current ratio

Define: 1) voltage ratio, 2) current ratio, 3) transformation ratio of transformer.

Description : Define: 1) voltage ratio, 2) current ratio, 3) transformation ratio of transformer.

Last Answer : 1) Voltage ratio: The voltages in primary and secondary winding is proportional to number of turns in primary and secondary respectively. So, the voltage ratio is same as transformation ratio. V2/V1 = N2 ... as transformation ratio of transformer. It is denoted by K. K = N2/N1

With fault clearing time, the transient stability of a power system

Description : With fault clearing time, the transient stability of a power system

Last Answer : With fault clearing time, the transient stability of a power system decreases

To protect the power transformer (Y-Y with neutral grounded) against fault, what type of connection do the CTs have ?

Description : To protect the power transformer (Y-Y with neutral grounded) against fault, what type of connection do the CTs have ?

Last Answer : To protect the power transformer (Y-Y with neutral grounded) against fault, what type of connection do the CTs have ? Δ-Δ connection

Fault diverters are basically?

Last Answer : Fault diverters are basically fast switches.

Which is the most common type of fault?

Description : Which is the most common type of fault?

Last Answer : Single phase to ground fault is the most common type of fault.

How to Gap a Spark Plug

Description : How to Gap a Spark Plug

Last Answer : How to Gap a Spark Plug For car customizers and auto enthusiasts, engine performance is a priority. One way to accomplish this is to set new gaps on your car engine's spark plugs. Here are ... With these steps, you can safely gap the spark plugs on your car to improve efficiency and performance.

Mention the precautions to be taken while connecting CT and PT in the circuit.

Description : Mention the precautions to be taken while connecting CT and PT in the circuit. 

Last Answer : Precautions to be taken while using instrument transformers: 1. Secondary of CT is never kept open circuited when it is energized. 2. Secondary of PT is never kept short circuited when it ... of the instrument transformers unless they are properly grounded. 8. Never connect to DC circuits.

Write any four differences between CT and PT.

Description : Write any four differences between CT and PT.

Last Answer : CT PT CT corresponds to current transformer PT corresponds to potential transformer CT primary is connected in series with load and secondary winding is connected to a low range ammeter. PT ... ) x PT ratio It is a step-up transformer. It is a step-down transformer

Why CT is never operated with an open secondary ?

Description : Why CT is never operated with an open secondary ?

Last Answer : CT secondary should never be kept open because it will cause saturation of the core to a high level and very high voltage will appear across the secondary which can breakdown the insulation. One terminal of PT secondary is always grounded to avoid capacitive induction and for human safety

The multiplier and the meter coil in a voltmeter are in?

Last Answer : The multiplier and the meter coil in a voltmeter are in series.

Give the causes and impact and reasons of grid system fault.

Description : Give the causes and impact and reasons of grid system fault. 

Last Answer : Following are the causes/reasons grid system fault: 1. Major imbalance between generation and consumption i.e. demand is more than generation. 2. Low frequency, due to some faults the frequency ... of supply and causes inconvenience to people. 6. Disturb the routine work of common all people.

If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded

Description : If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded transformer, then  (A) zero sequence currents are present on both sides of the transformer  (B) ... side  (D) zero sequence currents are present on the primary side but not on the secondary side

Last Answer : If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded transformer, then zero sequence currents are absent on both sides of the transformer 

A shunt fault is characterized by

Description : A shunt fault is characterized by (A) Increase in current, frequency and pf (B) Increase in current, reduction in frequency and pf (C) Increase in current and frequency, reduction in pf (D) Decrease in current and frequency

Last Answer : B

In the induction type directional over current relay, when a short-circuit occurs in the circuit

Description : In the induction type directional over current relay, when a short-circuit occurs in the circuit (A) power flows in reverse direction (B) power flows in normal direction (C) directional power element does not operate (D) over current element is not energized

Last Answer : In the induction type directional over current relay, when a short-circuit occurs in the circuit power flows in reverse direction

In order that current should flow without causing excessive heating or voltage drop, the relay contacts should?

Last Answer : In order that current should flow without causing excessive heating or voltage drop, the relay contacts should have low contact resistance, be clean and smooth, be of sufficient size and proper shape.

The eddy current loss in a dc generator is 400 W at 40 Hz frequency of reversal and constant flux density.

Description : The eddy current loss in a dc generator is 400 W at 40 Hz frequency of reversal and constant flux density. When frequency is increased to 50 Hz., eddy current loss is :  (A) 256 W (B) 320 W (C) 500 W (D) 625 W

Last Answer : The eddy current loss in a dc generator is 400 W at 40 Hz frequency of reversal and constant flux density. When frequency is increased to 50 Hz., eddy current loss is : 625 W

Define the following terms with respect to protective relays i) Relay time ii) Reset current iii) Plug setting multiplier and iv) Time setting multiplier

Description : Define the following terms with respect to protective relays i) Relay time ii) Reset current iii) Plug setting multiplier and iv) Time setting multiplier

Last Answer : 1) Relay Time: The time interval between occurrence of fault and closure of relay contacts.  2) Reset Current: The value of current below which the relay resets and comes back to ... The adjustment arrangement provided for setting the operation time of relay is known as Time setting multiplier. 

The operating point of a protective current transformer is near the

Description : The operating point of a protective current transformer is near the

Last Answer : The operating point of a protective current transformer is near the Ankle point

The inrush current of a transformer at no load is maximum if the supply voltage is switched on

Description : The inrush current of a transformer at no load is maximum if the supply voltage is switched on  (1) at peak voltage value (2) at zero voltage value (3) at half voltage value (4) at 0.866 time voltage value

Last Answer : At 0.866 time voltage value

ln HRC fuse the time between cut-off and final current zero is called

Description : ln HRC fuse the time between cut-off and final current zero is called

Last Answer : ln HRC fuse the time between cut-off and final current zero is called the arcing time

Given a unity feedback system with G(s)=k/s (s+4), the value of k for damping ratio of 0.5 is

Description : Given a unity feedback system with G(s)=k/s (s+4), the value of k for damping ratio of 0.5 is

Last Answer : Given a unity feedback system with G(s)=k/s (s+4), the value of k for damping ratio of 0.5 is 16

In otto cycle compression ratio is 8. Calculate air standard efficiency. Will it be grater than Carnot Cycle ? Justify your answer.

Description : In otto cycle compression ratio is 8. Calculate air standard efficiency. Will it be grater than Carnot Cycle ? Justify your answer. 

Last Answer : No, the Otto cycle efficiency 56.47% will always be lower than Carnot cycle efficiency. Justification: Carnot theorem states that keeping operating conditions same, Carnot engine is more efficient than any other engine. So, Otto cycle efficiency is lower than Carnot cycle efficiency. 

Graph indicating changes in pollutants level w.r.t air fuel ratio

Description : Graph indicating changes in pollutants level w.r.t air fuel ratio

Last Answer : Graph indicating changes in pollutants level w.r.t air fuel ratio

Compressor pressure ratio (CPR)

Description : Compressor pressure ratio (CPR)

Last Answer : Compressor pressure ratio (CPR), is the ratio of the air total pressure exiting the compressor to the air pressure entering the compressor. This number is always greater than 1.0.

SEER: Seasonal Energy Efficiency Ratio (SEER)

Description : SEER: Seasonal Energy Efficiency Ratio (SEER)

Last Answer : SEER: Seasonal Energy Efficiency Ratio (SEER), is most commonly used to measure the efficiency of a central air conditioner. The higher the SEER, the more efficient the system OR It is the ... the ratio of total capacity to the total KW energy usage at specific humidity and temperature condition.

Voltage ratio

Description : Voltage ratio

Last Answer : Voltage ratio

Turns ratio formula

Description : Turns ratio

Last Answer : Turns ratio formula

Impedance ratio

Description : Impedance ratio

Last Answer : Impedance ratio

What is transformation ratio?

Description : What is transformation ratio?

Last Answer : Transformation Ratio (k):- It is the ratio of secondary number of turns to primary number of turns. OR It is the ratio of secondary voltage to primary voltage. OR It is the ratio of primary current to secondary current. 

The ratio of the width to the height of the picture frame is called as

Description : The ratio of the width to the height of the picture frame is called as A) Rastar B) Aspect Ratio C) Length Ratio D) Efficiency  

Last Answer : The ratio of the width to the height of the picture frame is called as Aspect Ratio

A dc chopper is fed from a constant voltage mains the duty ratio of chopper is progressively increased while

Description : A dc chopper is fed from a constant voltage mains the duty ratio of chopper is progressively increased while the chopper feeds an RL load. The per unit current ripple would  (1) increase progressively  (2 ... 0.5 and then increase  (4) increase to a maximum value at α = 0.5 and then decrease

Last Answer : A dc chopper is fed from a constant voltage mains the duty ratio of chopper is progressively increased while the chopper feeds an RL load. The per unit current ripple would increase to a maximum value at α = 0.5 and then decrease

If Poisson's ratio of a resistance wire strain gauge is 1.8, then neglecting piezo-resistive effects, its Gauge

Description : If Poisson's ratio of a resistance wire strain gauge is 1.8, then neglecting piezo-resistive effects, its Gauge factor is :  (A) 2.8 (B) 2.6 (C) 4.6 (D) 3.6

Last Answer : If Poisson's ratio of a resistance wire strain gauge is 1.8, then neglecting piezo-resistive effects, its Gauge factor is : 4.6

The ratio of full -load volt-amperes to short-circuit volt-amperes is equal to :

Description : The ratio of full -load volt-amperes to short-circuit volt-amperes is equal to :

Last Answer : The ratio of full -load volt-amperes to short-circuit volt-amperes is equal to : Z (p.u)

Specific energy consumption of an electric train is the ratio between

Description : Specific energy consumption of an electric train is the ratio between (A) Specific energy output at driving wheels and efficiency of the traction motor (B) Specific energy output at driving wheels ... (D) Specific energy output at driving wheels and efficiency of the (motor + transmission gear)

Last Answer : Specific energy consumption of an electric train is the ratio between Specific energy output at driving wheels and efficiency of the (motor + transmission gear)

Ratio of the rotor reactance X to the rotor resistance R for a two-phase servo motor

Description : Ratio of the rotor reactance X to the rotor resistance R for a two-phase servo motor (A) is equal to that of a normal induction motor (B) is less than that of a normal induction motor (C) ... than that of a normal induction motor (D) may be less or greater than that of a normal induction motor

Last Answer : C

The Eb/V ratio of a d.c. motor is an indication of its?

Description : The Eb/V ratio of a d.c. motor is an indication of its?

Last Answer : The Eb/V ratio of a d.c. motor is an indication of its efficiency.

The ratio of mass of proton to that of electron is nearly?

Description : The ratio of mass of proton to that of electron is nearly?

Last Answer : The ratio of mass of proton to that of electron is nearly 1840.

Two bulbs of 500 W and 200 W rated at 250 V will have resistance ratio as?

Description : Two bulbs of 500 W and 200 W rated at 250 V will have resistance ratio as?

Last Answer : Two bulbs of 500 W and 200 W rated at 250 V will have resistance ratio as 2 : 5.

The ratio of active power to apparent power is known as____ factor.

Description : The ratio of active power to apparent power is known as____ factor.

Last Answer : The ratio of active power to apparent power is known as power factor.

The form factor is the ratio of?

Last Answer : The form factor is the ratio of r.m.s. value to average value.

The ratio of limiting friction and normal reaction is known as?

Description : The ratio of limiting friction and normal reaction is known as?

Last Answer : The ratio of limiting friction and normal reaction is known as coefficient of friction.

The mechanical power developed by a shunt motor will be maximum when the ratio of back e.m.f. to applied voltage is?

Last Answer : The mechanical power developed by a shunt motor will be maximum when the ratio of back e.m.f. to applied voltage is 0.5.

The ratio of starting torque to full-load torque is least in case of?

Last Answer : The ratio of starting torque to full-load torque is least in case of shunt motors.