The operating point of a protective current transformer is near the

The operating point of a protective current transformer is near the
by

1 Answer

Answer :

The operating point of a protective current transformer is near the Ankle point

by

Related questions

The secondary of a current transformer is always short-circuited under operating conditions because it?

Description : The secondary of a current transformer is always short-circuited under operating conditions because it?

Last Answer : The secondary of a current transformer is always short-circuited under operating conditions because it avoids core saturation and high voltage induction.

For a transformer, operating at constant load current, maximum efficiency will occur at?

Description : For a transformer, operating at constant load current, maximum efficiency will occur at?

Last Answer : For a transformer, operating at constant load current, maximum efficiency will occur at unity power factor.

If the % reactance upto the fault point is 20%, then the short circuit current will be

Description : If the % reactance upto the fault point is 20%, then the short circuit current will be

Last Answer : If the % reactance upto the fault point is 20%, then the short circuit current will be 5 times the full load current

A charge of 0.1 C moves past a given point every 0.01 s. How much is the current?

Description : A charge of 0.1 C moves past a given point every 0.01 s. How much is the current?

Last Answer : The current is 10.0A.  1ampere = 1 Coulomb per 1 second.  0.1Coulombs ÷ 0.01seconds = 10.0amperes.

Protective relays are devices that detect abnormal conditions in electrical circuits by measuring?

Last Answer : Protective relays are devices that detect abnormal conditions in electrical circuits by measuring constantly the electrical quantities which differ during normal and abnormal conditions.

Burden of a protective relay is the power?

Last Answer : Burden of a protective relay is the power absorbed by the circuit of relay.

An efficient and a well designed protective relaying should have?

Last Answer : An efficient and a well designed protective relaying should have good selectivity and reliability, economy and simplicity, high speed and selectivity.

A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred

Description : A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred resistance of 0.2 Ω and reactance of 0.5 Ω. The approximate primary induced emf is (A) 216 V (B) 226 V (C) 234 V (D) 236 V

Last Answer : A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred resistance of 0.2 Ω and reactance of 0.5 Ω. The approximate primary induced emf is 226 V

The inrush current of a transformer at no load is maximum if the supply voltage is switched on

Description : The inrush current of a transformer at no load is maximum if the supply voltage is switched on  (1) at peak voltage value (2) at zero voltage value (3) at half voltage value (4) at 0.866 time voltage value

Last Answer : At 0.866 time voltage value

The inverse definite mean time relays are used for over current and earth fault protection of transformer against?

Last Answer : The inverse definite mean time relays are used for over current and earth fault protection of transformer against internal short-circuits.

Blind spot is a point in the zones of protection where

Description : Blind spot is a point in the zones of protection where

Last Answer : Blind spot is a point in the zones of protection where No protection is available.

Step-down transformer converts high voltage and low current into:

Description : Step-down transformer converts high voltage and low current into:  (A) How voltage and high current (B) High voltage and low current (C) Low voltage and high current (D) None of the above

Last Answer : Step-down transformer converts high voltage and low current into: Low voltage and high current

In a single-phase transformer, the magnetizing current is

Description : In a single-phase transformer, the magnetizing current is (A) in phase with the no-load current (B) in quadrature with the no-load current (C) the product of no-load current and power factor (D) in phase with the flux in the core

Last Answer : In a single-phase transformer, the magnetizing current is in phase with the flux in the core

When secondary of a current transformer is open-circuited its iron core will be?

Description : When secondary of a current transformer is open-circuited its iron core will be?

Last Answer : When secondary of a current transformer is open-circuited its iron core will be hot because of heavy iron losses taking place in it due to high flux density.

In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of?

Description : In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of?

Last Answer : In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of less than 15A.

The operating time of instantaneous relay is

Description : The operating time of instantaneous relay is

Last Answer : The operating time of instantaneous relay is 0.1 sec

The relay operating speed depends upon?

Last Answer : The relay operating speed depends upon the spring tension, the rate of flux built up, armature core air gap.

Single point Cutting tool signature

Description : Single point Cutting tool signature

Last Answer : The shape of a tool is specified in a special sequence and this special sequence is called tool signature. The tool signature is given below (i) Back rake angle (ii) Side rake angle (iii) ... rake, end relief, side relief, end cutting edge, side cutting edge angle and 0.8 mm nose radius.

Illustrate with neat wiring diagram a single lamp control by two point method.

Description : Illustrate with neat wiring diagram a single lamp control by two point method.

Last Answer : Single lamp control by two point method:  This system is commonly used for stair case wiring. It consists of two way switches (the switch operates always in one of the two possible positions) the ... the person will change the position of switch S2, so that the lamp will be switched OFF'.

Three point starter can be used for?

Last Answer : Three point starter can be used for both shunt and compound motor.

A three point starter is considered suitable for?

Last Answer : A three point starter is considered suitable for shunt as well as compound motors.

In a load curve the highest point represents?

Last Answer : In a load curve the highest point represents peak demand.

what is the difference between four point starter and three point starter?

Description : what is the difference between four point starter and three point starter?

Last Answer : The shunt connection in four point starter is provided separately form the line where as in three point starter it is connected with line which is the drawback in three point starter.

How to Uninstall an Operating System ?

Description : How to Uninstall an Operating System ?

Last Answer : How to Uninstall an Operating System Even the most stable operating systems can crash, and suffer from irreparable damage that you may need to uninstall and reinstall them. Some users, though, may like to ... , you can easily remove the old, damaged operating system, and replace it with a new one.

operating principle of PUT.

Description :  operating principle of PUT.

Last Answer : Constructional diagram & Operating principle of PUT:  The PUT is a PNPN device similar to SCR, but its operation is similar to the UJT. The PUT behave like a UJT whose trigger voltage VP can be set ... low resistance and VAK ≈ 1V). The PUT is also referred to as a complementary SCR (CSCR). 

Transistor operating configurations

Description : Transistor operating configurations

Last Answer : Transistor operating configurations

Draw construction of Megger and write operating principle of it.

Description : Draw construction of Megger and write operating principle of it.

Last Answer : Megger:  Working: Two coils the current coil and pressure coil are mounted at an angle on the same spindle and form the part of the moving system. These coils are connected to a small hand driven ... . When the instrument is not working the pointer may rest at any position on the dial.

Explain the operating principle of LASER and list applications of LASER diode.

Description : Explain the operating principle of LASER and list applications of LASER diode.

Last Answer : A basic construction of Laser diode is as shown . A PN junction is formed by two layers of doped gallium arsenide. There is highly reflective surface at one end of PN junction and ... 6. laser scanning and light beam illumination. 7. Military applications 8. Medical surgery 9.Diamond cutting

The command line interpreter that enables the users to interact with operating system is called the

Description : The command line interpreter that enables the users to interact with operating system is called the A) Window B) Shell C) Process D) Kernel 

Last Answer : The command line interpreter that enables the users to interact with operating system is called the Shell 

A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are :

Description : A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are :  (A) less than 66 kV (B) lie between 66 kV and 110 kV (C) more than 165 kV (D) lie between 110 kV and 165 kV

Last Answer : A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are : lie between 66 kV and 110 kV

In a single-phase induction motor, the operating direction is determined by the ________

Description : In a single-phase induction motor, the operating direction is determined by the ________ A) Rotor B) Stator C) Starting circuit D) None of these

Last Answer : In a single-phase induction motor, the operating direction is determined by the Starting circuit

What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016

Description : What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

Last Answer : What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a

Description : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) ... proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

Last Answer : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ directly proportional to α and inversely proportional to Φ

In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load,

Description : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is (A) sinusoidal current (B) constant dc current (C) continuous rectangular pulses (D) alternating rectangular pulses

Last Answer : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is alternating rectangular pulses

Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power

Description : Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power characteristics have a common slope of 1 MW/Hz and the no-load frequencies of the generators are 51.5 Hz and 51.0 Hz, ... system frequency is (A) 50 Hz (B) 51 Hz (C) 51.25 Hz (D) 51.5 Hz

Last Answer : Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power characteristics have a common slope of 1 MW/Hz and the no-load frequencies of the generators are 51.5 Hz and 51.0 Hz, respectively. Then the system frequency is 50 Hz

Operating torques in analogue instruments are?

Last Answer : Operating torques in analogue instruments are deflecting, control and damping.

The operating voltage of a meggar is about?

Last Answer : The operating voltage of a meggar is about 100 V.

To limit the operating temperature an electrical machine should have proper?

Last Answer : To limit the operating temperature an electrical machine should have proper current rating.

The operating speed of a synchronous motor can be changed to new fixed value by?

Last Answer : The operating speed of a synchronous motor can be changed to new fixed value by changing frequency.

Annual operating expenditure of a power plant consists of?

Last Answer : Annual operating expenditure of a power plant consists of fixed charges, semi-fixed charges, running charges.

Operating frequency of power MOSFET is higher than that of power BJT. Justify the statement.

Description : Operating frequency of power MOSFET is higher than that of power BJT. Justify the statement.

Last Answer : Power MOSFET have high turning on and turning off capability high switching speed of MOSFET is due to the high rate of change of drain voltage. The switching losses of power MOSFET ... lower frequency. Hence, operating frequency of power MOSFET is higher than that of power BJT.

what are the three operating regions of BJT?

Last Answer : Active , Saturation , Cut-off region of operations in BJT.

If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug

Description : If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug setting multiplier will be

Last Answer : If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug setting multiplier will be 10

The eddy current loss in a dc generator is 400 W at 40 Hz frequency of reversal and constant flux density.

Description : The eddy current loss in a dc generator is 400 W at 40 Hz frequency of reversal and constant flux density. When frequency is increased to 50 Hz., eddy current loss is :  (A) 256 W (B) 320 W (C) 500 W (D) 625 W

Last Answer : The eddy current loss in a dc generator is 400 W at 40 Hz frequency of reversal and constant flux density. When frequency is increased to 50 Hz., eddy current loss is : 625 W

In the induction type directional over current relay, when a short-circuit occurs in the circuit

Description : In the induction type directional over current relay, when a short-circuit occurs in the circuit (A) power flows in reverse direction (B) power flows in normal direction (C) directional power element does not operate (D) over current element is not energized

Last Answer : In the induction type directional over current relay, when a short-circuit occurs in the circuit power flows in reverse direction

ln HRC fuse the time between cut-off and final current zero is called

Description : ln HRC fuse the time between cut-off and final current zero is called

Last Answer : ln HRC fuse the time between cut-off and final current zero is called the arcing time

In order that current should flow without causing excessive heating or voltage drop, the relay contacts should?

Last Answer : In order that current should flow without causing excessive heating or voltage drop, the relay contacts should have low contact resistance, be clean and smooth, be of sufficient size and proper shape.

In which fault the maximum short circuit current occurs?

Description : In which fault the maximum short circuit current occurs?

Last Answer : In three phase bolted fault the maximum short circuit occurs.

Which of the following is not a part of transformer installation?

Description : Which of the following is not a part of transformer installation?  (A) Conservator (B) Breather (C) Buchholz Relay (D) Exciter

Last Answer : Which of the following is not a part of transformer installation?  (A) Conservator (B) Breather (C) Buchholz Relay (D) Exciter

The core construction is like spokes of a wheel in following transformer:

Description : The core construction is like spokes of a wheel in following transformer:  (A) Berry Type Transformer (B) Core Type Transformer (C) Shell Type Transformer (D) None of the above

Last Answer : The core construction is like spokes of a wheel in following transformer:  Berry Type Transformer