In an R-C phase shift oscillator, the minimum no. of R-C networks to be connected in cascade will be -

In an R-C phase shift oscillator, the minimum no. of R-C networks to be connected in cascade will be -
by

1 Answer

Answer :

In an R-C phase shift oscillator, the minimum no. of R-C networks to be connected in cascade will be 3

by
reshown

Related questions

Draw and explain RC phase shift Oscillator.

Description : Draw and explain RC phase shift Oscillator.

Last Answer : Circuit diagram of RC phase shift oscillator: WORKING: * Circuit consists of a single stage amplifier in common emitter configuration & RC phase shifting network. * R1, R2, RE provides biasing & CE ... . * The phase shift around the loop is 3600 only at one precise frequency.  

Oscillator independent of phase shift is

Description : Oscillator independent of phase shift is  (1) Relaxation (2) Wein bridge (3) Clapp (4) All of these

Last Answer : Oscillator independent of phase shift is Relaxation 

Two port networks are connected in cascade. The parameters of the network are obtained by multiplying in individual

Description : Two port networks are connected in cascade. The parameters of the network are obtained by multiplying in individual

Last Answer : Two port networks are connected in cascade. The parameters of the network are obtained by multiplying in individual ABCD parameter matrix

Explain Three Phase Bidirectional Delta Connected Controller.

Description : Explain Three Phase Bidirectional Delta Connected Controller.

Last Answer : Three Phase Bidirectional Delta Connected Controller:

State the need of cascade amplifier and draw circuit diagram of 2-stage direct coupled amplifier.

Description : State the need of cascade amplifier and draw circuit diagram of 2-stage direct coupled amplifier.

Last Answer : Need:- The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, in order to obtain greater voltage and power gain, cascade amplifiers are used.

State the need of cascade amplifier.

Description : State the need of cascade amplifier.

Last Answer : Most systems a single transistor amplifier does not provide sufficient gain or bandwidth or will not have the correct input or output impedance matching. Hence cascade amplifier is use which consist more than one stages of amplification.

How To Make Cascade Generator

Description : How To Make Cascade Generator

Last Answer : This cascade engine was invented in the 1930's by a 17-year old amateur experimenter who was simply trying to make a new version of the old Fizeau's condenser. Instead, he discovered a ... a gravitic pressure wave in the surrounding space. Higher voltage and pulse rate generates greater thrust.

In a 4-pole wave winding connected dc motor, the cross-magnetizing AT/pole for a brush shift of θ radians

Description : In a 4-pole wave winding connected dc motor, the cross-magnetizing AT/pole for a brush shift of θ radians (A) Armature amp-conductors × (θ/360o) (B) Armature amp-turns × (θ/360o) (C) Armature amp-conductors × (1/4 - θ/360o) (D) Armature amp-conductors × (1/8 - θ/360o)

Last Answer : In a 4-pole wave winding connected dc motor, the cross-magnetizing AT/pole for a brush shift of θ radians Armature amp-conductors × (1/8 - θ/360o)

State the need of multistage amplifier. Draw frequency response of R-C coupled amplifier.

Description : State the need of multistage amplifier. Draw frequency response of R-C coupled amplifier.

Last Answer : The need of multistage amplifier The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, in ... to use a MULTISTAGE AMPLIFIER .  Frequency response of R-C coupled amplifier.

In a series R-C circuit, with the increase in frequency, current

Description : In a series R-C circuit, with the increase in frequency, current (A) Reduces (B) Increases (C) Does not change (D) Becomes zero

Last Answer : In a series R-C circuit, with the increase in frequency, current Increases

Compare amplifier and oscillator.

Description : Compare amplifier and oscillator.

Last Answer : Figure shows a block diagram of an amplifier and an oscillator.   An amplifier is a device, which produces an output signal with similar waveform as that of the input. ... is supplied. An oscillator does not require any external signal to start or maintain energy conversion process.

crystal oscillator and its applications.

Description : crystal oscillator and its applications.

Last Answer : Need: Any circuit that generates an alternating voltage is called an oscillator. To generate ac Voltage, it takes energy from the dc source. 1. In some applications voltages of low frequency are required where ... generate clock in digital systems.  It is used as sweep circuits in TV and CRO.

Compare RC and LC oscillator.

Description : Compare RC and LC oscillator.

Last Answer :  RC and LC oscillator

List two types of oscillator, which generates frequency in RF range.

Description : List two types of oscillator, which generates frequency in RF range.

Last Answer : Types of Oscillators generating frequencies in RF range: i) Hartley Oscillator ii) Colpitt’s Oscillator iii) Clapp Oscillator

Draw the circuit diagram of crystal oscillator and explain its working.

Description : Draw the circuit diagram of crystal oscillator and explain its working.

Last Answer : To excite a crystal for operation in the series-resonant mode it may be connected as a series element in a feedback path, the crystal impedance is the smallest and the amount of positive feedback is the largest. ... which is good.  The resonant frequency is given as  Fo = 1/( 2 π √LC ) 

Draw and explain Hartley Oscillator circuit diagram.

Description : Draw and explain Hartley Oscillator circuit diagram.

Last Answer : Function of each component: 1. An NPN transistor connected in a common emitter configuration works as the active device in amplifier stage and CE configuration provides 180°phase shift. 2. R1 and R2 ... circuit to the base-emitter circuit.  The frequency of oscillation is given as-  

Is this oscillator adjustable with a screwdriver, and where is the link to prchase it?

Description : Is this oscillator adjustable with a screwdriver, and where is the link to prchase it?

Last Answer : answer:@XOIIO Probably a question you should direct to the company. The link below should help. http://www.vectron.com/contact/index.htm

Describe triggering of SCR using UJT relaxation oscillator.

Description : Describe triggering of SCR using UJT relaxation oscillator. 

Last Answer : I need it's operation

Which of the following is a negative-resistance microwave device for oscillator applications?

Description :  Which of the following is a negative-resistance microwave device for oscillator applications? A) IMPATT Diode B) Gunn Diode C) Snap diode D) Schottky Diode 

Last Answer :  Which of the following is a negative-resistance microwave device for oscillator applications? A) IMPATT Diode B) Gunn Diode C) Snap diode D) Schottky Diode 

A Hartley Oscillator is used for generating

Description : A Hartley Oscillator is used for generating (A) very low frequency Oscillation (B) radio-frequency Oscillation (C) microwave Oscillation (D) audio-frequency Oscillation

Last Answer : A Hartley Oscillator is used for generating radio-frequency Oscillation

Do you hold shift when you type in ALL CAPS or do you use caps lock?

Description : Do you hold shift when you type in ALL CAPS or do you use caps lock?

Last Answer : Yes.

How to Shift Gears in a Car ?

Description : How to Shift Gears in a Car ?

Last Answer : How to Shift Gears in a Car Driving a shift stick offers many benefits especially for drivers who don't like monotony on the road. First-timers are recommended to practice driving using a shift stick ... If you enjoy learning this article, you'll surely be delighted in reading how to learn driving.

How to Survive Working Night Shift ?

Description : How to Survive Working Night Shift ?

Last Answer : How to Survive Working Night Shift Very early in our lives, we have been trained to follow a certain routine. We wake up in the morning, do our tasks for the day and sleep at night. Working on ... 're on the graveyard shift. For more information regarding this article, read how to stay up all night.

Shift Register

Description : Shift Register

Last Answer : Shift Register:- Shift Register is a group of flipflops used to shift data from one side to other side or to convert serial data into parallel or vice versa. Shift registers are of following types  i) ... iii) Parallel in serial out(PISO) iv) Parallel in parallel out(PIPO)

The sequence components of current of a single-phase load connected to a 3-phase system are

Description : The sequence components of current of a single-phase load connected to a 3-phase system are (A) equal positive and negative sequence components (B) equal positive, negative and zero sequence components (C) vector sum of sequence currents is zero (D) algebraic sum of sequence currents is zero

Last Answer : The sequence components of current of a single-phase load connected to a 3-phase system are equal positive, negative and zero sequence components

A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are :

Description : A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are :  (A) less than 66 kV (B) lie between 66 kV and 110 kV (C) more than 165 kV (D) lie between 110 kV and 165 kV

Last Answer : A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are : lie between 66 kV and 110 kV

what is the minimum voltage required to turn on a diode ?

Description : what is the minimum voltage required to turn on a diode ?

Last Answer : 0.7 v sil and 0.3 v for gr

Define each of following terms: i) Connected load ii) Spinning reserve.

Description : Define each of following terms: i) Connected load ii) Spinning reserve. 

Last Answer : i) Connected Load :- It is the sum of load of all equipment connected to supply system which are in use or not in use of each consumer. ii) Spinning Reserve:- It is reserved generating capacity in operation and connected to bus bar and ready to take a load.

A connected graph has ‘5’ number of branches and ‘4’ number of nodes. It's rank is

Description :  A connected graph has ‘5’ number of branches and ‘4’ number of nodes. It's rank is A) 1 B) 2 C) 3 D) 4 

Last Answer :  A connected graph has ‘5’ number of branches and ‘4’ number of nodes. It's rank is 3 

Two 100W, 200V lamps are connected in series across a 200V supply. The total power

Description : Two 100W, 200V lamps are connected in series across a 200V supply. The total power consumed by each lamp will be in Watts

Last Answer : 4800

Three identical resistors connected in star consume 5000 W. If the resistors are connected in

Description : Three identical resistors connected in star consume 5000 W. If the resistors are connected in delta across the same supply, the power consumed will be

Last Answer : Three identical resistors connected in star consume 5000 W. If the resistors are connected in delta across the same supply, the power consumed will be 15000 W

Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch

Description : Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

Last Answer : Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

When three resistors with unequal values are connected in parallel, _______

Description : When three resistors with unequal values are connected in parallel, _______ A) The current across the resistors is the same  B) The voltage drop across the resistors is the same C) The voltage drops across the resistors is proportional to the resistance of each resistor D) None of these

Last Answer : When three resistors with unequal values are connected in parallel, The voltage drop across the resistors is the same

What is the total resistance if 5 resistors of 20 Ω each are connected in series?

Description : What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

Last Answer : What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

Cells are connected in series in order to?

Description : Cells are connected in series in order to?

Last Answer : Cells are connected in series in order to increase voltage available.

The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse

Description : The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

Last Answer : The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current

Description : A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current requirement is 0.2 A. The minimum voltage at input is 24 V. What is the required value of series resistance with source? A) 5.45 Ω B) 6 Ω C) 7.2 Ω D) 6.38 Ω  

Last Answer : A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current requirement is 0.2 A. The minimum voltage at input is 24 V. What is the required value of series resistance with source? A) 5.45 Ω B) 6 Ω C) 7.2 Ω D) 6.38 Ω  

For optimum generator scheduling for different power plants, the minimum fuel cost is obtained when

Description : For optimum generator scheduling for different power plants, the minimum fuel cost is obtained when

Last Answer : For optimum generator scheduling for different power plants, the minimum fuel cost is obtained when The incremental fuel cost of each plant multiplied by the penalty factor is the same

Which of the following circuit breakers has high reliability & minimum maintenance?

Description : Which of the following circuit breakers has high reliability & minimum maintenance?  (A) Bulk oil type CB (B) Air blast CB (C) Vacuum CB (D) Sulphur hexafluoride CB 

Last Answer : Which of the following circuit breakers has high reliability & minimum maintenance?  (A) Bulk oil type CB (B) Air blast CB (C) Vacuum CB (D) Sulphur hexafluoride CB 

The Minimum Oil Circuit Breaker (MOCB) is named because of :

Description : The Minimum Oil Circuit Breaker (MOCB) is named because of :  (A) Reduced requirement of oil (B) Reduced requirement of air (C) All of the above (D) None of the above

Last Answer : The Minimum Oil Circuit Breaker (MOCB) is named because of : Reduced requirement of oil 

ln a minimum oil circuit breaker the oil is used

Description : ln a minimum oil circuit breaker the oil is used

Last Answer : ln a minimum oil circuit breaker the oil is used to act as circuit breaking medium only

The minimum charge on an ion is?

Description : The minimum charge on an ion is?

Last Answer : The minimum charge on an ion is equal to the charge of an electron.

Build using minimum number of CMOS gates.

Description : Build using minimum number of CMOS gates. Three input NAND gate. Two input NOR gate Three input NOR gate Two input AND gate Two input OR gate

Last Answer : Three input NAND gate. Two input NOR gate Three input NOR gate Two input AND gate Two input OR gate

Minimum voltage regulation occurs when the power factor of the load is?

Description : Minimum voltage regulation occurs when the power factor of the load is?

Last Answer : Minimum voltage regulation occurs when the power factor of the load is leading.

Can anyone tell me why my iPad won't let me log in to our internet at home?

Description : Can anyone tell me why my iPad won't let me log in to our internet at home?

Last Answer : answer:If I was you I would disable WEP/WPA in the router and try with that. If it can connect then you can start troubleshooting further. And Allie had a problem with her AppleTV connecting to the LAN ... problem. So yeah, turn off the security stuff in the router and see if it will connect then.

What does your social landscape look like, and are you content with it?

Description : What does your social landscape look like, and are you content with it?

Last Answer : In my youth social activities were everything….now I prefer to dial it down and spend my time relaxing with my gal. The weekly open mike jam sessions now take care of the social fix I still enjoy!

If I get a wireless network adapter, will this work?

Description : If I get a wireless network adapter, will this work?

Last Answer : What do you mean by “This”?

Explain the concept of following terms : (i) Connected load (ii) Maximum demand

Last Answer : 1. Connected Load: It is the sum of load of all equipment's connected to supply system which are in use or not in use of each consumer. OR   The sum of connected load of all consumers ... is the maximum load which a consumer uses at a particular time period out of his total connected load. 

Define the terms: i) Tariff ii) Fuel surcharge iii) Electricity Duty iv) Connected load

Description : Define the terms: i) Tariff ii) Fuel surcharge iii) Electricity Duty iv) Connected load

Last Answer : i) Tariff: The rate at which a consumer is charged for the consumption of electricity is called as tariff. OR The amount of money framed by the supplier for the supply of electrical energy ... is the total wattage of all appliances which are used by the consumer on his sanctioned connection. 

Define the following terms related to tariff: (i) Connected load (ii) Unit consumed (iii) Fixed charges (iv) Electricity Tax

Description : Define the following terms related to tariff: (i) Connected load (ii) Unit consumed (iii) Fixed charges (iv) Electricity Tax 

Last Answer : (i) Connected load  It is the sum of the power ratings (Watts or kW or MW) of all devices and machines existing (installed) in the premises of consumer. It is used to decide the ... a percentage of the total electricity bill which includes all amounts that go to the electricity supply agency.