The main component responsible for the fall of gain of an RC coupled amplifier in low frequency

The main component responsible for the fall of gain of an RC coupled amplifier in low frequency range is 

(A) The active device itself (tube, or transistor) 

(B) stray shunt capacitance Cs 

(C) the grid leak resistance Rg 

(D) coupling capacitor Cc
by

1 Answer

Answer :

The main component responsible for the fall of gain of an RC coupled amplifier in low frequency range is coupling capacitor Cc

by

Related questions

Harmonic distortion of the signal is produced in an RC coupled transistor amplifier. The probable

Description : Harmonic distortion of the signal is produced in an RC coupled transistor amplifier. The probable component responsible for this distortion is  (A) The transistor itself  (B) the power supply Vcc  (C) the coupling capacitor Cc  (D) the biasing resistors

Last Answer : Harmonic distortion of the signal is produced in an RC coupled transistor amplifier. The probable component responsible for this distortion is The transistor itself 

The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency end and bypass capacitors at the low frequency end C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and D) shunt capacitors at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Description : The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency ... at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Last Answer : C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and

In a resistance loaded, RC coupled amplifier the dc component is blocked by A) Load resistance RL B) Coupling capacitor, CC C) RB D) The transistor.

Description : In a resistance loaded, RC coupled amplifier the dc component is blocked by A) Load resistance RL B) Coupling capacitor, CC C) RB D) The transistor.

Last Answer : B) Coupling capacitor, CC

Draw circuit diagram of two stage RC coupled amplifier using BJT

Description : Draw circuit diagram of two stage RC coupled amplifier using BJT

Last Answer : BJT - To amplify input signal. R1 & R2 = Biasing resistor to provide DC biasing voltage RE = Emitter resistor to control gain RL = Load resistor to carry load current Cin = Cout = Coupling capacitors to block DC CE = emitter bypass resistor

applications of RC coupled amplifier

Description :  applications of RC coupled amplifier

Last Answer : Applications of RC coupled amplifier: (i) Widely used as Voltage amplifiers. (ii) They are used in Public Address System. (iii) In Tape recorders. (iv) In stereo amplifiers (v) In T.V. V.C.R. and C.D. Players.

advantages and disadvantages of direct coupled amplifier over RC coupled amplifier.

Description : advantages and disadvantages of direct coupled amplifier over RC coupled amplifier. 

Last Answer : Advantages:  Due to absence of coupling capacitors, the gain does not reduce on the lower frequency side.  This amplifier can amplify dc signals. Reduced cost and complexity due to absence of ...   The output waveform has a dc shift.  Poor frequency response at a higher frequency.

Compare RC coupled, transformer coupled and direct coupled amplifier based on four points.

Description : Compare RC coupled, transformer coupled and direct coupled amplifier based on four points.

Last Answer : Parameter RC coupled Transformer coupled Direct coupled  Coupling element Resistor and capacitor Transformer No element Impedance matching Poor Excellent good Frequency ... Low frequency amplifier,opamp Size and cost small Large and bulky least

Draw the single stage RC coupled amplifier circuit and explain its’s operation.

Description : Draw the single stage RC coupled amplifier circuit and explain its’s operation.

Last Answer : Operation:- The capacitors C1 and C2 are called as the coupling capacitors. As the load resistor RL (not shown in the diagram) is coupled to the amplifier through the coupling capacitor ... connected in the common emitter (CE) configuration. Therefore, this amplifier is called CE amplifier. 

List the advantages of RC coupled amplifier.

Description : List the advantages of RC coupled amplifier.

Last Answer : Advantages: 1. The frequency response is excellent 2. The circuit is very compact and extremely light 3. Cost is low because it employ resistors and capacitors which are cheap 

What is the use of RC coupled amplifier?

Last Answer : the RC coupled amplifier are using the following applications first in public address amplifier system  tape recorders TV VCR and CD players stereo amplifier  and these are the voltage amplification amplifiers

The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is

Description : The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

Last Answer : The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ.

Description : An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: (1) 1/11 kΩ (2) 1/5 kΩ (3) 5 kΩ (4) 11 kΩ

Last Answer : An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: 1/11 kΩ

The gain of an FET amplifier can be changed by changing:

Description : The gain of an FET amplifier can be changed by changing: (1) rm (2) gm (3) Rd (4) None of these

Last Answer : The gain of an FET amplifier can be changed by changing: gm

If the feedback factor of an amplifier is 0.1 and its gain without feedback is 40, then its gain with feedback is

Description : If the feedback factor of an amplifier is 0.1 and its gain without feedback is 40, then its gain with feedback is (a) – 13.3 (b) 200 (c) 8 (d) 10 

Last Answer : If the Feedback Factor of an amplifier is 0.1 and its gain without feedback is 40, then feedback is 40,then its gain with feedback is 8.

For a feedback amplifier, if the loop gain is much greater than unity, the closed loop gain will be equal to

Description : For a feedback amplifier, if the loop gain is much greater than unity, the closed loop gain will be equal to

Last Answer : For a feedback amplifier, if the loop gain is much greater than unity, the closed loop gain will be equal to inverse of feedback factor

An amplifier without feedback has a gain of 1000. The gain with a negative feedback of 0.009 is

Description : An amplifier without feedback has a gain of 1000. The gain with a negative feedback of 0.009 is  A) 10 B) 100 C) 125 D) 900

Last Answer : 100

An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V.

Description : An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is  A) 25 micro-volt B) 50 micro-volt C) 5 Volts D) 10 volts

Last Answer : An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is 50 micro-volt

The voltage gain of a common base amplifier depends on

Description : The voltage gain of a common base amplifier depends on  1. Load resistor RL 2. input resistance of transistor 3. Ac alpha 4. All the above 

Last Answer : The voltage gain of a common base amplifier depends on  1. Load resistor RL 2. input resistance of transistor 3. Ac alpha 4. All the above 

The closed-loop voltage gain of an inverting amplifier equal to

Last Answer : The closed-loop voltage gain of an inverting amplifier equal to The feedback resistance divided by the input resistance.

An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is

Description : An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is the r.m.s. noise voltage at the input to this amplifier if the ambient temperature is 27o C

Last Answer : An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is the r.m.s. noise voltage at the input to this amplifier if the ambient temperature is 27o C 18.2 microvolt

The main function of the transformer used in the output of a power amplifier is

Description : The main function of the transformer used in the output of a power amplifier is  (A) To step up the voltage  (B) to increase the voltage gain  (C) to safeguard the transistor against overheating  (D) to match the load impedance with dynamic output resistance of the transistor

Last Answer : The main function of the transformer used in the output of a power amplifier is to match the load impedance with dynamic output resistance of the transistor

State the need of multistage amplifier. Draw frequency response of R-C coupled amplifier.

Description : State the need of multistage amplifier. Draw frequency response of R-C coupled amplifier.

Last Answer : The need of multistage amplifier The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, in ... to use a MULTISTAGE AMPLIFIER .  Frequency response of R-C coupled amplifier.

A low noise amplifier has an effective noise temperature of 50 k. The absolute noise figure is

Description : A low noise amplifier has an effective noise temperature of 50 k. The absolute noise figure is

Last Answer : A low noise amplifier has an effective noise temperature of 50 k. The absolute noise figure is 1.172

What component in an amplifier circuit tends to limit the low-frequency response of the amplifier?

Description : What component in an amplifier circuit tends to limit the low-frequency response of the amplifier?

Last Answer : The coupling capacitor (C3).

The ideal operational amplifier does not have:

Description : The ideal operational amplifier does not have: (1) Infinite input resistance (2) Infinite output resistance (3) Infinite voltage gain (4) Infinite bandwidth 

Last Answer : The ideal operational amplifier does not have: Infinite output resistance

For Cascode amplifier the output impedance becomes

Description : For Cascode amplifier the output impedance becomes 

Last Answer : For Cascode amplifier the output impedance becomes very high

In a radio receiver the IF amplifier

Description : In a radio receiver the IF amplifier  (A) is tuned above the stations incoming frequency (B) amplifies the output of local oscillator (C) is fixed tuned to one particular frequency (D) can be tuned to various isolate frequencies

Last Answer : In a radio receiver the IF amplifier is fixed tuned to one particular frequency

Class A amplifier is used when

Description : Class A amplifier is used when  (A) No phase inversion is required (B) Highest voltage gain is required (C) dc voltages are to be amplified (D) Minimum distortion is desired. 

Last Answer : Class A amplifier is used when Minimum distortion is desired. 

Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will

Description : Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will   (A) Amplify the noise as much as the signal (B) Reduce the noise (C) Increase the noise (D) Not effect the noise

Last Answer : Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will Reduce the noise

In an IF amplifier, the IF transformer is provided with tapping to

Description : In an IF amplifier, the IF transformer is provided with tapping to  (a) increase the voltage gain (b) increase the bandwidth of the resonance circuit (c) increase the impedance ... resonance circuit to the following cascaded amplifier (d) increase the quality factor of the resonance circuit 

Last Answer : In an IF amplifier, the IF transformer is provided with tapping to increase the voltage gain

In a Klystron amplifier, the RF voltage produces

Description : In a Klystron amplifier, the RF voltage produces  (a) amplitude modulation (b) frequency modulation (c) phase modulation (d) velocity modulation

Last Answer : In a Klystron amplifier, the RF voltage produces velocity modulation

In class - A power amplifier, the collector dissipation is maximum when

Description : In class - A power amplifier, the collector dissipation is maximum when  (a) no signal is present  (b) signal swing is maximum  (c) signal swing is (1/1.414) of its maximum  (d) none of the above

Last Answer : In class - A power amplifier, the collector dissipation is maximum when no signal is present

In Class ‘B’ amplifier, the output current flows for

Description : In Class ‘B’ amplifier, the output current flows for

Last Answer : In Class ‘B’ amplifier, the output current flows for half input cycle

The efficiency of a class B push-pull amplifier is

Description : The efficiency of a class B push-pull amplifier is

Last Answer : The efficiency of a class B push-pull amplifier is 75-80%

Which of the following amplifier has the least distortion.

Description : Which of the following amplifier has the least distortion. • Class E • Class D • Class C • Class A

Last Answer : Which of the following amplifier has the least distortion. • Class E • Class D • Class C • Class A

The battery operated pre-amplifier with a consumption of 10 Watts can work on battery of 12

Description : The battery operated pre-amplifier with a consumption of 10 Watts can work on battery of 12 volt, 100 AH having efficiency of 50% for • 120 hrs. • 60 hrs. • 100 hrs. • 10 hrs.

Last Answer : The battery operated pre-amplifier with a consumption of 10 Watts can work on battery of 12 volt, 100 AH having efficiency of 50% for 60 hrs.

In class-A amplifier conduction extends over 360° because the operating point.

Description : In class-A amplifier conduction extends over 360° because the operating point.  1. Located near saturation point 2. Located at or near cut-off point 3. Located on load line 4. Located in the centre of load line 

Last Answer : In class-A amplifier conduction extends over 360° because the operating point.  1. Located near saturation point 2. Located at or near cut-off point 3. Located on load line 4. Located in the centre of load line 

Just as a voltage amplifier signal voltage a power amplifier.

Description : Just as a voltage amplifier signal voltage a power amplifier.  1.amplifier power  2.amplifier signal  3.converts the signal ac power into DC power  4.converts a dc power into useful AC power 

Last Answer : Just as a voltage amplifier signal voltage a power amplifier.  1.amplifier power  2.amplifier signal  3.converts the signal ac power into DC power  4.converts a dc power into useful AC power 

Negative feedback in an amplifier is accompanied by

Description : Negative feedback in an amplifier is accompanied by (A) Gain less sensitive to component variations (B) Increase in gain (C) Decrease in bandwidth (D) None of the above

Last Answer : Negative feedback in an amplifier is accompanied by Gain less sensitive to component variations 

What is the importance of negative feedback in the operational amplifier?

Description : What is the importance of negative feedback in the operational amplifier? (A) It maintains the gain (B) The voltage difference between the input terminals is maintained at a very small value ( ... value (D) The voltage difference between the input terminals is maintained at a very high value

Last Answer : The voltage difference between the input terminals is maintained at a very small value

If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?

Description : If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?

Last Answer : A step-down transformer.

In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0045 A. common emitter B. common collector C. darlington paired, capacitor coupled D. common base

Description : In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0045 A. common emitter B. common collector C. darlington paired, capacitor coupled D. common base

Last Answer : Answer: D

Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Description : Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Last Answer : D. Local oscillator

What problem is caused in an rf amplifier by a loosely coupled transformer?

Description : What problem is caused in an rf amplifier by a loosely coupled transformer?

Last Answer : A too-narrow bandpass.

transformer coupled amplifier

Description :  transformer coupled amplifier

Last Answer :  transformer coupled amplifier

State the need of cascade amplifier and draw circuit diagram of 2-stage direct coupled amplifier.

Description : State the need of cascade amplifier and draw circuit diagram of 2-stage direct coupled amplifier.

Last Answer : Need:- The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, in order to obtain greater voltage and power gain, cascade amplifiers are used.

The output stage of a practical amplifier is always - - - coupled

Last Answer : The output stage of a practical amplifier is always Transformer coupled

An Op-amp as a voltage follower has a voltage gain of

Description : An Op-amp as a voltage follower has a voltage gain of

Last Answer : An Op-amp as a voltage follower has a voltage gain of Unity

A non inverting closed loop op amp circuit generally has a gain factor

Last Answer : A non inverting closed loop op amp circuit generally has a gain factor Greater than one.

RC time constant characteristics, as shown in the illustration, are important in _____________. EL-0086 A. bridge rectifiers for alternator excitation B. timing and pulse shaping circuits C. transistor power amplifier biasing D. motor controller overload protection

Description : RC time constant characteristics, as shown in the illustration, are important in _____________. EL-0086 A. bridge rectifiers for alternator excitation B. timing and pulse shaping circuits C. transistor power amplifier biasing D. motor controller overload protection

Last Answer : Answer: B