Pulse – amplitude modulation signals are  multiplexed by using

1 Answer

Answer :

FET switches

Related questions

Description : A pulse modulation technique as the width of a constant amplitude pulse is varied proportional to the amplitude of the analog signal at the time the signal is sampled.

Last Answer : PWM, PLM, PDM

Description : Pulse width modulation may be generated:

Last Answer : with a monostable multivibrator

Description : n digital modulation, it is similar to standard amplitude modulation except there is only two amplitudes possible.

Last Answer : amplitude shift keying

Description : Used for transmission of PCM encoded time – division multiplexed digital signal.

Last Answer : T carriers

Description : Which of the following systems is not used in radio detection and ranging? A. Frequency shift B. Frequency modulation C. Pulse radar D. Amplitude modulation

Last Answer : D. Amplitude modulation

Description : ECE Board Exam March 1996 One type of pulse communications system uses pulse that appear as a group, and which vary in number according to the loudness of the voice. This type of ... A. pulse duration modulation B. pulse amplitude modulation C. pulse code modulation D. pulse position modulation

Last Answer : A. pulse duration modulation

Description : What, if any, noise susceptibility advantage exists for pulse-amplitude modulation over analog amplitude modulation?

Last Answer : Both are susceptible to noise and interference

Description : In an AM transmitter with 100% modulation, the voltage of the final RF stage will be

Last Answer : approximately four times the DC supply voltage

Description : It is the ratio of the transmission bit rate to the minimum bandwidth required for a particular modulation scheme

Last Answer : Bandwidth efficiency, Information density, or Spectral efficiency

Description : Which is not purpose of modulation?

Last Answer : Increase in signal power

Description : Rate of change of a signal on a transmission medium after encoding and modulation have occurred

Last Answer : baud rate

Description : A modulation technique where data rates in excess of 56 kbps can be achieved over telephone circuits

Last Answer : Trellis Code Modulation

Description : The upper pulse rate and information carrying capacity of a cable is limited by:

Last Answer : modal dispersion

Description : The width of the vertical sync pulse in the Philippine TV system is

Last Answer : 3H

Description : The width of the vertical sync pulse in the Philippine TV system is

Last Answer : 3H

Description : Category of data transmission if the binary pulse is maintained for the entire bit time?

Last Answer : Return to zero

Description : In an amplitude modulated waveform, the amplitude of the sideband is

Last Answer : 1/2 carrier amplitude x modulation index

Description : Ten signals, each requiring 3000 Hz, are multiplexed on to a single channel using FDM. How much minimum bandwidth is required for the multiplexed channel ? Assume that the guard bands are 300 Hz wide. (A) 30,000 (B) 32,700 (C) 33,000 (D) None of the above

Last Answer : (B) 32,700

Description : Modulation means A. Varying of information B. Utilization of a single transmission channel to carry multiple signals C. Varying of some parameters of a carrier such as its amplitude to transmit information D. Transmit pulses in DC form on a copper wire

Last Answer : C. Varying of some parameters of a carrier such as its amplitude to transmit information

Description : A system where the modulated RF picture and sound carrier signals are distributed in a cable network, instead of wireless system.

Last Answer : CATV

Description : Emphasizing low-level signals and compressing higher level signals is called:

Last Answer : companding

Description : Image frequencies occur when two signals ____.

Last Answer : enter the mixer, one below and one above the local oscillator by a difference equal to the IF

Description : It is the most prevalent encoding technique used for TDM signals:

Last Answer : PCM

Description : It is a system where the digital signals are placed directly on the coaxial cable.

Last Answer : Baseband

Description : The most common method used for sampling voice signals in PCM systems.

Last Answer : flat top sampling

Description : In a star-topology Ethernet LAN, _______ is just a point where the signals coming from different stations collide; it is the collision point.

Last Answer : a passive hub

Description : ____ system transmits frequency-division-multiplexed voice band signals over a coaxial cable for distances up to 4000 miles. A. T carrier B. X carrier C. L carrier D. F carrier

Last Answer : C. L carrier

Description : Analog signals can be ________by combining them with a carrier frequency (A) Carried (B) Transported (C) Multiplexed (D) Mixed

Last Answer : (C) Multiplexed

Description : They proposed a new communication medium using cladded fiber cables.

Last Answer : Kao and Bockham

Description : Four channels are multiplexed using TDM. If each channel sends 100 bytes/second and we multiplex 1 byte per channel, then the bit rate for the link is __________. a. 400 bps b. 800 bps c. 1600 bps d. 3200 bps

Last Answer : d. 3200 bps

Description : Four channels are multiplexed using TDM. If each channel sends 100 bytes/second and we multiplex 1 byte per channel, then the bit rate for the link is ............... (A) 400 bps (B) 800 bps (C) 1600 bps (D) 3200 bps

Last Answer : (D) 3200 bps Answer: D Explanation: The multiplexer is shown in the Figure. Each frame carries 1 byte from each channel; the size of each frame, therefore, is 4 bytes, or 32 bits. Because each ... channel, the frame rate must be 100 frames per second. The bit rate is 100 32 = 3200 bps. 

Description : What is pulse-width modulation (PWM) in Arduino?

Last Answer : Pulse-width modulation (PWM) in Arduino is a technique used to control the brightness of an LED or the speed of a motor by varying the duty cycle of a digital signal.

Description : What is a pulse-width modulation (PWM) signal in Arduino?

Last Answer : A PWM signal in Arduino is a digital signal that varies the width of the pulse to simulate an analog signal.

Description : A technique used by codes to convert an analog signal into a digital bit stream is known as A) Pulse code modulation B) Pulse stretcher C) Query processing D) Queue management

Last Answer : Answer : A

Description : Type of modulation used in TV broadcast visual transmitter. A. Pulse modulation B. DSBFC C. Vestigial sideband D. SSBFC

Last Answer : C. Vestigial sideband

Description : Modulation in which no signal is present between pulses A. Pulse modulation B. QAM C. PSK D. FSK

Last Answer : A. Pulse modulation

Description : ECE Board Exam March 1996 Which of the following pulse modulation systems is analog? A. Delta B. Differential PCM C. PWM D. PCM

Last Answer : C. PWM

Description : ECE Board Exam March 1996 The modulation system used for telegraphy is A. frequency-shift keying B. two-tone modulation C. pulse-code modulation D. single-tone modulation

Last Answer : A. frequency-shift keying

Description : What is Pulse Width Modulation?

Last Answer : Ans-Pulse width modulation is a modulation technique in which the width of the pulse is varied in accordance with the message signal. Pulse width Modulation is abbreviated as PWM. PWM can be used ... the pulse train and recover an average analog waveform. PWM is used in sound synthesis circuits.

Description : What is the primary advantage of pulse-modulation systems?

Last Answer : . Low susceptibility to noise.

Description : Pulse-code modulation requires the use of approximations of value that are obtained by what process?

Last Answer : Quantization.

Description : What is pulse-frequency modulation?

Last Answer : A method of pulse modulation in which a modulating wave is used to frequency modulate a pulse-generating circuit

Description : What is the main disadvantage of pulse-position modulation?

Last Answer : It requires synchronization between the transmitter and receiver.

Description : Which edges of the pulse can be modulated in pulse duration modulation?

Last Answer : Either, or both at the same time.

Description : What characteristics of a pulse can be changed in pulse time modulation?

Last Answer : The time duration of the pulses or the time of occurrence of the pulses.

Description : To ensure the accuracy of a transmission, what is the minimum number of times a modulating wave should be sampled in pulse modulation?

Last Answer : 2.5 times the highest modulating frequency.

Description : What action is necessary to impress intelligence on the pulse train in pulse modulation?

Last Answer : Some characteristic of the pulses has to be varied.

Description : A technique used by codes to convert an analog signal into a digital bit stream is known as a. Pulse code modulation b. Pulse stretcher c. Query processing d. Queue management

Last Answer : a. Pulse code modulation

Description : A technique used by codes to convert an analog signal into a digital bit stream is known as a. Pulse code modulation b. Pulse stretcher c. Query processing d. Queue management

Last Answer : a. Pulse code modulation

Description : A technique used by codes to convert an analog signal into a digital bit stream is known as a. Pulse code modulation b. Pulse stretcher c. Query processing d. Queue management

Last Answer : a. Pulse code modulation