In fiber optics, SCS stands for
∙ a. Suppressed-clad-silicon  
∙ b. Silicon base-class-silica  
∙ c. Silica-clad-silica  
∙ d. Serial-clad-silicon

1 Answer

Answer :

c. Silica-clad-silica

Related questions

Description : In fiber optics, PCS stands for ∙ a. Plastic-clad-silica ∙ b. Polyethylene-clad-silica ∙ c. Personal carrier system ∙ d. Personal communication

Last Answer : ∙ a. Plastic-clad-silica

Description : The three essential types of fiber commonly used today except: ∙ A. Plastic core and cladding ∙ B. Plastic core and glass cladding ∙ C. Glass core and glass cladding (SCS) ∙ D. Glass core and plastic cladding (PCS)

Last Answer : B. Plastic core and glass cladding

Description : SONET stands for ∙ a. System Optical Network ∙ b. Synchronous Optical Network ∙ c. Silica Optic Network ∙ d. System Optical Fiber Net

Last Answer : ∙ b. Synchronous Optical Network

Description : He coined the term “fiber optics” in 1956. ∙ A. Kapany ∙ B. Kao ∙ C. Bockham ∙ D. Keck

Last Answer : ∙ A. Kapany

Description : Used to test a fiber optics splice ∙ a. Spectrum analyzer ∙ b. Oscilloscope ∙ c. Optical power meter ∙ d. Field strength meter

Last Answer : c. Optical power meter

Description : Why are visible-light LEDs not used for fiber optics? ∙ a. It has high losses ∙ b. It has short wave ∙ c. It has low attenuation ∙ d. It has weak signal

Last Answer : ∙ a. It has high losses

Description : The following are the cause of light attenuation in fiber optics except ∙ a. Backscattering ∙ b. Absorption ∙ c. Refraction ∙ d. Microbends

Last Answer : c. Refraction

Description : In fiber optics, higher-order mode refers to ∙ a. Cladding boundary at high angle ∙ b. Backscattering electromagnetic signals ∙ c. Diffracting signals ∙ d. All of these

Last Answer : ∙ a. Cladding boundary at high angle

Description : Which of the following is a disadvantage for plastic fiber optics? ∙ a. Noise immunity ∙ b. Electric hazards ∙ c. Higher losses ∙ d. All of these

Last Answer : c. Higher losses

Description : Infrared range for fiber optics ∙ a. 400 – 700 nm ∙ b. 700 – 1200 nm ∙ c. 300 – 2000 nm ∙ d. 400 – 7000 nm

Last Answer : b. 700 – 1200 nm

Description : Which of the following is used as an optical receiver in fiber optics communications ∙ a. APD ∙ b. Tunnel diode ∙ c. Laser diode ∙ d. LED

Last Answer : a. APD

Description : A dielectric waveguide for the propagation of electromagnetic energy at light frequencies ∙ a. Stripline ∙ b. Microstrip ∙ c. Laser beam ∙ d. Fiber optics

Last Answer : d. Fiber optics

Description : What is the insertion loss of connector-type splices for a single mode fiber optics? ∙ a. 0.51 dB ∙ b. 0.31 dB ∙ c. 0.49 dB ∙ d. 0.38 dB

Last Answer : d. 0.38 dB

Description : What is the average insertion loss of fusion splice in fiber optics? ∙ a. 0.09 dB ∙ b. 0.9 dB ∙ c. 0.19 dB ∙ d. 0.009 dB

Last Answer : ∙ b. 0.9 dB

Description : It is caused by valence electrons in the silica material from which the fiber are manufactured. ∙ A. ion resonance absorption ∙ B. infrared absorption ∙ C. ultraviolet absorption ∙ D. visible light absorption

Last Answer : ultraviolet absorption

Description : ____ is applied to protect core and cladding of the fiber ∙ a. Insulation ∙ b. Fiber insulation ∙ c. Silica ∙ d. Polymer jacket

Last Answer : d. Polymer jacket

Description : The dominant loss mechanisms in silica fiber are ∙ a. Absorption and radiation losses ∙ b. Absorption and Rayleigh scattering ∙ c. Coupling and radiation losses ∙ d. Radiation and modal dispersion

Last Answer : b. Absorption and Rayleigh scattering

Description : It refers to the abrupt of change in refractive index from core to clad ∙ A. step index ∙ B. graded index ∙ C. semi-graded index ∙ D. half step index

Last Answer : ∙ A. step index

Description : Proposed the use of clad glass fiber as a dielectric waveguide a. Karpon and Keck b. Karpon and Bockham c. Bockham and Kao d. Kao and Keck

Last Answer : c. Bockham and Kao

Description : Optical power is sometimes called __________. ∙ A. Radiant emission ∙ B. Radiant power ∙ C. Radiant flux ∙ D. Radiant optics

Last Answer : C. Radiant flux

Description : Define fiber optics.

Last Answer : Fiber optics is the branch of optical technology concerned with the transmission of radiant power (light energy) through fibers.

Description : Between silicon and gallium arsenide, which has the greatest index of refraction? ∙ A. Gallium arsenide ∙ B. Neither of silicon nor gallium arsenide ∙ C. Silicon ∙ D. They are equal

Last Answer : Gallium arsenide

Description : What is the stage of the sand becoming a silicon? ∙ a. Liquid ∙ b. Gas ∙ c. Molten ∙ d. Hot

Last Answer : c. Molten

Description : The term power budgeting refers to ∙ A. the cost of cable, connectors, equipment and installation ∙ B. the loss of power due to defective components ∙ C. the total power available minus the attenuation losses ∙ D. the comparative costs of fiber and copper installations

Last Answer : C. the total power available minus the attenuation losses

Description : Which type of fiber-optic cable is the most widely used? ∙ A. single-mode step-index ∙ B. multimode step-index ∙ C. single-mode graded index ∙ D. multimode graded index

Last Answer : B. multimode step-index

Description : EMD is best described by which statement? ∙ A. 70 percent of the core diameter and 70% of the fiber NA should be filled with light. ∙ B. 70 percent of the fiber diameter and 70% of the ... be measured at the output. ∙ D. 70 percent of the unwanted wavelengths should be attenuated by the fiber.

Last Answer : 70 percent of the core diameter and 70% of the fiber NA should be filled with light.

Description : Which of the following is not a major benefit of a fiber-optic cable? ∙ A. immunity from interference ∙ B. no electrical safety problems ∙ C. excellent data security ∙ D. lower cost

Last Answer : ∙ D. lower cost

Description : The core of fiber-optic cable is surrounded by ∙ A. wire braid shield ∙ B. Keviar ∙ C. cladding ∙ D. plastic insulation

Last Answer : ∙ C. cladding

Description : The core of a fiber-optic cable is made of ∙ A. air ∙ B. glass ∙ C. diamond ∙ D. quartz

Last Answer : B. glass

Description : Which of the following is not a common type of fiber-optic cable? ∙ A. single-mode step-index ∙ B. multimode graded-index ∙ C. single-mode graded-index ∙ D. multimode step-index

Last Answer : . single-mode graded-index

Description : The operation of a fiber-optic cable is based on the principle of ∙ A. refraction ∙ B. reflection ∙ C. dispersion ∙ D. absorption

Last Answer : A. refraction

Description : A popular light wavelength fiber-optic cable is ∙ A. 0.7 micrometer ∙ B. 1.3 micrometer ∙ C. 1.5 micrometer ∙ D. 1.8 micrometer

Last Answer : B. 1.3 micrometer

Description : Which type of fiber optic cable is best for very high speed data? ∙ A. single-mode step-index ∙ B. multimode step-index ∙ C. single-mode graded-index ∙ D. multimode graded-index

Last Answer : A. single-mode step-index

Description : When connector losses, splice losses and coupler losses are added, what is the limiting factor? ∙ A. source power ∙ B. fiber attenuation ∙ C. connector and splice loss ∙ D. detector sensitivity

Last Answer : D. detector sensitivity

Description : For a 300-m optical fiber cable with a bandwidth distance product of 600 MHz-km, determine the bandwidth. ∙ A. 5 GHz ∙ B. 1 GHz ∙ C. 2 GHz

Last Answer : C. 2 GHz

Description : It indicates what signal frequencies can be propagated through a given distance of fiber cable. ∙ A. Bandwidth Distance Product ∙ B. Pulse width dispersion ∙ C. Rise time ∙ D. Cutoff frequency

Last Answer : A. Bandwidth Distance Product

Description : How can modal dispersion reduced entirely? ∙ A. Use a graded index fiber ∙ B. Use a single-mode fiber ∙ C. Use a monochromatic light source ∙ D. Use a very sensitive light detector

Last Answer : Use a single-mode fiber

Description : It is caused by the difference in the propagation time of light rays that take different paths down the fiber. ∙ A. modal dispersion ∙ B. microbending ∙ C. Rayleigh scattering ∙ D. chromatic dispersion

Last Answer : A. modal dispersion

Description : These bends are caused by excessive pressure and tension and generally occur while fiber are bent during handling or installation. ∙ A. microbending ∙ B. macrobending ∙ C. constant-radius bending ∙ D. kinks

Last Answer : C. constant-radius bending

Description : Chromatic dispersion can be eliminated by __________. ∙ A. using a monochromatic light source ∙ B. using a very small numerical aperture fiber ∙ C. using a graded-index fiber ∙ D. using a very sensitive photo detector

Last Answer : A. using a monochromatic light source

Description : Light rays that are emitted simultaneously from an LED and propagated down an optical fiber do not arrive at the far end of the fiber at the same time results to ∙ A. intramodal dispersion ∙ B. pulse length dispersion ∙ C. modal dispersion ∙ D. wavelength dispersion

Last Answer : D. wavelength dispersion

Description : Which type of fiber-optic cable has the least modal dispersion? ∙ A. single-mode step-index ∙ B. multimode step-index ∙ C. single-mode graded-index ∙ D. multimode graded-index

Last Answer : A. single-mode step-index

Description : It is analogous to power dissipation to copper cables, impurities in the fiber absorb the light and covert it to heat. ∙ A. power loss ∙ B. absorption loss ∙ C. resistive loss ∙ D. heat loss

Last Answer : B. absorption loss

Description : A type of index of an optical fiber that has no cladding and whose central core has a non-uniform refractive index. ∙ A. graded index ∙ B. multimode ∙ C. single mode ∙ D. step-index

Last Answer : ∙ A. graded index

Description : A type of index profile of an optical fiber that has a central core and outside cladding with a uniform refractive index ∙ A. multimode ∙ B. graded index ∙ C. step-index ∙ D. single mode

Last Answer : ∙ C. step-index

Description : It is a graphical representation of the magnitude of the refractive index across the fiber. ∙ A. mode ∙ B. index profile ∙ C. numerical aperture ∙ D. refractive index

Last Answer : B. index profile

Description : More than one path for light rays to take down the fiber ∙ A. Multimode ∙ B. Step-index ∙ C. Single mode

Last Answer : A. Multimode

Description : Only one path for light rays to take down the fiber ∙ A. Multimode ∙ B. Step-index ∙ C. Single mode ∙ D. Graded index

Last Answer : C. Single mode

Description : The effect of a large magnitude of the numerical aperture ∙ A. The amount of external light the fiber will accept is greater. ∙ B. The amount of external light the fiber will accept is less. ... The amount of modal dispersion will be less. ∙ D. The amount of chromatic dispersion will be greater.

Last Answer : The amount of external light the fiber will accept is greater.