Description : What is the average insertion loss of fusion splice in fiber optics? ∙ a. 0.09 dB ∙ b. 0.9 dB ∙ c. 0.19 dB ∙ d. 0.009 dB
Last Answer : ∙ b. 0.9 dB
Description : Which of the following is used as an optical receiver in fiber optics communications ∙ a. APD ∙ b. Tunnel diode ∙ c. Laser diode ∙ d. LED
Last Answer : a. APD
Description : When connector losses, splice losses and coupler losses are added, what is the limiting factor? ∙ A. source power ∙ B. fiber attenuation ∙ C. connector and splice loss ∙ D. detector sensitivity
Last Answer : D. detector sensitivity
Description : Optical power is sometimes called __________. ∙ A. Radiant emission ∙ B. Radiant power ∙ C. Radiant flux ∙ D. Radiant optics
Last Answer : C. Radiant flux
Description : What is the average loss in fiber splice? ∙ a. 0.10 dB ∙ b. 0.15 dB ∙ c. 0.20 dB ∙ d. 0.25 dB
Last Answer : 0.15 dB
Description : He coined the term “fiber optics” in 1956. ∙ A. Kapany ∙ B. Kao ∙ C. Bockham ∙ D. Keck
Last Answer : ∙ A. Kapany
Description : Why are visible-light LEDs not used for fiber optics? ∙ a. It has high losses ∙ b. It has short wave ∙ c. It has low attenuation ∙ d. It has weak signal
Last Answer : ∙ a. It has high losses
Description : The following are the cause of light attenuation in fiber optics except ∙ a. Backscattering ∙ b. Absorption ∙ c. Refraction ∙ d. Microbends
Last Answer : c. Refraction
Description : In fiber optics, higher-order mode refers to ∙ a. Cladding boundary at high angle ∙ b. Backscattering electromagnetic signals ∙ c. Diffracting signals ∙ d. All of these
Last Answer : ∙ a. Cladding boundary at high angle
Description : Which of the following is a disadvantage for plastic fiber optics? ∙ a. Noise immunity ∙ b. Electric hazards ∙ c. Higher losses ∙ d. All of these
Last Answer : c. Higher losses
Description : Infrared range for fiber optics ∙ a. 400 – 700 nm ∙ b. 700 – 1200 nm ∙ c. 300 – 2000 nm ∙ d. 400 – 7000 nm
Last Answer : b. 700 – 1200 nm
Description : In fiber optics, SCS stands for ∙ a. Suppressed-clad-silicon ∙ b. Silicon base-class-silica ∙ c. Silica-clad-silica ∙ d. Serial-clad-silicon
Last Answer : c. Silica-clad-silica
Description : In fiber optics, PCS stands for ∙ a. Plastic-clad-silica ∙ b. Polyethylene-clad-silica ∙ c. Personal carrier system ∙ d. Personal communication
Last Answer : ∙ a. Plastic-clad-silica
Description : A dielectric waveguide for the propagation of electromagnetic energy at light frequencies ∙ a. Stripline ∙ b. Microstrip ∙ c. Laser beam ∙ d. Fiber optics
Last Answer : d. Fiber optics
Description : What is the insertion loss of connector-type splices for a single mode fiber optics? ∙ a. 0.51 dB ∙ b. 0.31 dB ∙ c. 0.49 dB ∙ d. 0.38 dB
Last Answer : d. 0.38 dB
Description : The mechanical splice is best suited for ∙ A. quicker installation under ideal condition ∙ B. minimum attenuation losses ∙ C. field service conditions ∙ D. situations in which cost of equipment is not a factor
Last Answer : D. situations in which cost of equipment is not a factor
Description : Which of the following is not a part of the optical spectrum? ∙ A. infrared ∙ B. ultraviolet ∙ C. visible color ∙ D. x-rays
Last Answer : ∙ D. x-rays
Description : Which of the following is not part of the optical spectrum? ∙ a. Infrafed ∙ b. Ultraviolet ∙ c. Visible color ∙ d. X-rays
Last Answer : ∙ d. X-rays
Description : Optical cable testers are used for ∙ a. Checking refractive index ∙ b. Light power out of a fiber ∙ c. Non-calibrated light into a fiber
Last Answer : b. Light power out of a fiber
Last Answer : ∙ b. Light power out of a fiber
Description : How much is the power loss of the fusion splice? ∙ a. 0.1 dB or less ∙ b. 0.01 dB or less ∙ c. 1 dB or less ∙ d. 10 dB or less
Last Answer : a. 0.1 dB or less
Description : Most fiber optic light sources emit light in which spectrum? ∙ A. visible ∙ B. infrared ∙ C. ultraviolet ∙ D. X-ray
Last Answer : B. infrared
Description : Most fiber-optic light sources emit light in which spectrum? ∙ a. Visible ∙ b. Infrared ∙ c. Ultraviolet ∙ d. X-ray
Last Answer : ∙ b. Infrared
Description : For a 300-m optical fiber cable with a bandwidth distance product of 600 MHz-km, determine the bandwidth. ∙ A. 5 GHz ∙ B. 1 GHz ∙ C. 2 GHz
Last Answer : C. 2 GHz
Description : Light rays that are emitted simultaneously from an LED and propagated down an optical fiber do not arrive at the far end of the fiber at the same time results to ∙ A. intramodal dispersion ∙ B. pulse length dispersion ∙ C. modal dispersion ∙ D. wavelength dispersion
Last Answer : D. wavelength dispersion
Description : A type of index of an optical fiber that has no cladding and whose central core has a non-uniform refractive index. ∙ A. graded index ∙ B. multimode ∙ C. single mode ∙ D. step-index
Last Answer : ∙ A. graded index
Description : A type of index profile of an optical fiber that has a central core and outside cladding with a uniform refractive index ∙ A. multimode ∙ B. graded index ∙ C. step-index ∙ D. single mode
Last Answer : ∙ C. step-index
Description : Developed an optical fiber with losses less that 2 dB/km ∙ A. Kao and Bockham ∙ B. Maiman, Kao and Bockham ∙ C. Maiman and Schawlow ∙ D. Kapron, Keck and Maurer
Last Answer : ∙ A. Kao and Bockham
Description : Approximately what is the frequency limit of the optical fiber? ∙ A. 20 MHz ∙ B. 1 MHz ∙ C. 100 MHz ∙ D. 40 GHz
Last Answer : ∙ D. 40 GHz
Description : What is the frequency limit of an optical fiber? ∙ a. 20 GHz ∙ b. 30 GHz ∙ c. 40 GHz ∙ d. 50 GHz
Last Answer : ∙ c. 40 GHz
Description : Light traveling in optical fiber follows which of the following principles. ∙ a. Huygen’s principle ∙ b. Reflection theory ∙ c. Light theory ∙ d. Snell’s law
Last Answer : d. Snell’s law
Description : Which is not a possible cause of optical fiber loss? ∙ a. Impurities ∙ b. Glass attenuation ∙ c. Stepped index operation ∙ d. Microbending
Last Answer : ∙ c. Stepped index operation
Description : The graded-index multimode optical fiber has a core diameter of _____ nm. ∙ a. 0.5 ∙ b. 0.05 ∙ c. 0.0005 ∙ d. 5
Last Answer : ∙ a. 0.5
Description : A step-index multimode optical fiber has a core diameter of _____ nm. ∙ a. 0.02 ∙ b. 0.2 ∙ c. 2 ∙ d. 0.002
Last Answer : b. 0.2
Description : A single mode optical fiber has a core diameter of _____ nm. ∙ a. 0.1 ∙ b. 0.01 ∙ c. 0.2 ∙ d. 0.05
Last Answer : a. 0.1
Description : SONET stands for ∙ a. System Optical Network ∙ b. Synchronous Optical Network ∙ c. Silica Optic Network ∙ d. System Optical Fiber Net
Last Answer : ∙ b. Synchronous Optical Network
Description : Which of the following is used as an optical transmitter on the Fiber Optical Communications? ∙ a. APD ∙ b. LSA diode ∙ c. PIN diode ∙ d. LED
Last Answer : d. LED
Description : What is a specific path the light takes in an optical fiber corresponding to a certain angle and number of reflection ∙ a. Mode ∙ b. Grade ∙ c. Numerical Aperture ∙ d. Dispersion
Last Answer : a. Mode
Description : The bandwidth of optical fiber ∙ a. 900M Hz ∙ b. 900 PHz ∙ c. 900 THz ∙ d. 900 EHz
Last Answer : c. 900 THz
Description : Is the different angle of entry of light into an optical fiber when the diameter of the core is many times the wavelength of the light transmitted. ∙ a. Acceptance angle ∙ b. Modes ∙ c. Sensors ∙ d. Aperture
Last Answer : b. Modes
Description : The core of an optical fiber has a ∙ a. Lower refracted index than air ∙ b. Lower refractive index than the cladding ∙ c. Higher refractive index than the cladding ∙ d. Similar refractive index with the cladding
Last Answer : c. Higher refractive index than the cladding
Description : Band loss is ∙ a. A reduction in transmitter power caused by earth’s surface curvature ∙ b. A reduction in strength of the signal caused by folded dipole bends ∙ c. An attenuation increase caused by bends radiating from the side of the fiber ∙ d. All of these
Last Answer : c. An attenuation increase caused by bends radiating from the side of the fiber
Description : The mechanical splice attenuation loss is _____ dB or less ∙ a. 0.1 ∙ b. 0.01 ∙ c. 0.001 ∙ d. 1
Description : The loss in single-mode fiber-optic cable due to a splice is about: a. 0.02 dB b. 0.2 dB c. 1 dB d. 3 dB
Last Answer : a. 0.02 dB
Description : Which tester is used to measure SWR? A. Spectrum analyzer B. Multimeter C. Reflectometer D. Oscilloscope
Last Answer : C. Reflectometer
Description : Define fiber optics.
Last Answer : Fiber optics is the branch of optical technology concerned with the transmission of radiant power (light energy) through fibers.
Description : The minimum optical power a light detector can receive and still produce a usable electrical output signal. ∙ A. light responsivity ∙ B. light sensitivity ∙ C. light collectivity ∙ D. illumination
Last Answer : B. light sensitivity
Description : The term responsivity as it applies to a light detector is best described as ∙ A. the time required for the signal to go from 10 to 90 percent of maximum amplitude ∙ B. the ratio of the diode ... . the ratio of the input power to output power ∙ D. the ratio of output current to input current
Last Answer : the ratio of the diode output current to the input optical power
Description : For a single mode optical cable with 0.25 dB/km loss, determine the optical power 100 km from a 0.1-mW light source. ∙ A. -45 dBm ∙ B. -15 dBm ∙ C. -35 dBm
Last Answer : ∙ C. -35 dBm
Description : It is described as the flow of light energy past a given point in a specified time ∙ A. Optical radiation ∙ B. Optical impedance ∙ C. Optical illusion ∙ D. Optical power
Last Answer : D. Optical power