What is the typical power range for thermocouple sensors?

What is the typical power range for thermocouple sensors?
by

1 Answer

Answer :

0.1uW to 100mW
by

Related questions

What sensor provides a change of resistance with typical power range of 1uW to 10mW and with maximum frequency greater than 100GHz

Description : What sensor provides a change of resistance with typical power range of 1uW to 10mW and with maximum frequency greater than 100GHz

Last Answer : thermistor sensor

A sensing element that provides a dc voltage less than 10mV with typical power range of 0.1 to 100mW

Description : A sensing element that provides a dc voltage less than 10mV with typical power range of 0.1 to 100mW

Last Answer : thermal converters

The output voltage of a thermocouple

Description : The output voltage of a thermocouple

Last Answer : increases with temperature

What is the typical full-scale voltage across a moving coil voltmeter?

Description : What is the typical full-scale voltage across a moving coil voltmeter?

Last Answer : 50mV

What is the typical full-scale deflection current of a moving coil instrument?

Description : What is the typical full-scale deflection current of a moving coil instrument?

Last Answer : 50mA

You are given a mercury manometer range 0 -760 mm ? A vacuum gauge reads 60 mm vacuum. The test manometer reads 50 vacuum ? Which of the two in correct.

Description : You are given a mercury manometer range 0 -760 mm ? A vacuum gauge reads 60 mm vacuum. The test manometer reads 50 vacuum ? Which of the two in correct.

Last Answer : The transmitter is correct because 760 - 50 = 710 mm abs.

How will you calibrate an absolute pressure transmitter using vacuum manometer. Range 0-400mm abs ?

Description : How will you calibrate an absolute pressure transmitter using vacuum manometer. Range 0-400mm abs ?

Last Answer : The procedure for calibration is as follows : Connect air supply to the transmitter. Connect a test gauge of 0-1.4 Kg/cm2 to the output. Connect Vacuum pump with tee off to the manometer. Apply 760 ... nearest ) and adjust zero. Apply 360 mm Vacuum adjust span. ( 760 - 360 = 400 mm abs. )

A device or instrument, which delivers signals of precise frequency and amplitude, usually over a wide range

Description : A device or instrument, which delivers signals of precise frequency and amplitude, usually over a wide range

Last Answer : signal generators

This instrument measures temperatures by electric means, especially temperatures beyong the range of mercury thermometers

Description : This instrument measures temperatures by electric means, especially temperatures beyong the range of mercury thermometers

Last Answer : pyrometer

Current range extension in moving coil instruments can be achieved by placing a ___ in shunt with the instrument.

Description : Current range extension in moving coil instruments can be achieved by placing a ___ in shunt with the instrument.

Last Answer : low resistance resistor

An electrodynamic meter used t measure power

Description : An electrodynamic meter used t measure power

Last Answer : wattmeter

Type of power-line frequency meter composed of vibrating iron reed placed in alternating magnetic field

Description : Type of power-line frequency meter composed of vibrating iron reed placed in alternating magnetic field

Last Answer : Vibrating Reed Type

A bridge used to locate accidental grounds on communications and power lines

Description : A bridge used to locate accidental grounds on communications and power lines

Last Answer : Murray Loop

Type of power-line frequency meter device utilizing a principle of balancing an indicator needle at center of a scale using magnetic fields opposing each other.

Description : Type of power-line frequency meter device utilizing a principle of balancing an indicator needle at center of a scale using magnetic fields opposing each other.

Last Answer : magnetic type

A common technique for measuring power at high frequency is to ______

Description : A common technique for measuring power at high frequency is to ______

Last Answer : employ a sensing element that converts the RF power to a measureable dc or low-frequency signal

A device used to mechanically measure the output power of a motor

Description : A device used to mechanically measure the output power of a motor

Last Answer : dynamometer

Thermocouple instruments can be used for a frequency range upto

Description : Thermocouple instruments can be used for a frequency range upto   (a) 100Hz (b) 5000 Hz (c) 1 MHz (d) 50 MHz and above 

Last Answer : Thermocouple instruments can be used for a frequency range upto 50 MHz and above 

What is a filter used for ?

Description : What is a filter used for ?

Last Answer : The half wave and full wave signals are pulsating D . C . voltages. The use of such voltages is limited to charging batteries, running D. C. motors, and a few other applications. What we really ... voltage from a battery. To get a constant voltage from this, we can use a capacitor input filter. 

What is Zener Diode ? What is a voltage Regulator ?

Description : What is Zener Diode ? What is a voltage Regulator ?

Last Answer : The breakdown region of a p n diode can be made very sharp and almost vertical Diodes with almost vertical breakdown region are known as Zever Diodes. A Zener diodes operating in the breakdown ... VOLTAGE REGULATOR : The output remains constant despite changes in input voltage due to Zever effect.  

What is transistor ? What are the different types ?

Description : What is transistor ? What are the different types ?

Last Answer : A transistor is a three lagged semi conductor device. Basically a transistor means (transfer - resister). Whether the transistor is pnp or npn it resembles two diodes (back to back). The one of the left ... transistor : Emitter - Base - Forward Bias. Collector - Base - Reverse Bias. 

What is CB, CE and CC configuration ?

Description : What is CB, CE and CC configuration ?

Last Answer : Buffer : A device or a circuit used to isolate two pt'ne circuits or stages. The emitter follows is a example of buffer. Alpha = IC / IE Beta = IC / IB

How will you test a transistor with a multimeter. ?

Description : How will you test a transistor with a multimeter. ?

Last Answer : 1. Emitter +ve of meter and Base -ve output = Low resistance 2. Emitter -ve of meter and base +ve output = High resistance. 3. Collector +ve and Base -ve output = Low. 4. Collector -ve and base +ve output = High. Emitter : Collector = High Resistance. PNP : Opposite Results. 

What is a thyristor ? What are its uses ?

Description : What is a thyristor ? What are its uses ?

Last Answer : A thyristor is a special kind of semi conductor device that uses internal feedback to produce latching action. Use : Used for controlling large amounts of load power in motors, heaters, lighting systems etc ... the latches like a open switch. This latch will always stay in open or close position.  

What does a transmitter output start from 3-15 psi or (0.2 - 1 Kg/Cm2) or 4 - 20 ma. etc. ?

Description : What does a transmitter output start from 3-15 psi or (0.2 - 1 Kg/Cm2) or 4 - 20 ma. etc. ? 

Last Answer : The transmitter output stance from what is known as "live zero". This system has specific advantages : 1. The systems automatically alarms when the signal system becomes inoperative. ... transmitter operating, but transmitting a zero measurement and a failure, in the signal system. 

What are Intrinsically safe system ?

Description : What are Intrinsically safe system ?

Last Answer : Intrinsic safety is a technique for designing electrical equipment for safe use in locations made hazardous by the presence of flammable gas or vapors in air. "Defn. :" Intrinsically safe circuit is ... , unfortunately, been adopted in all countries. However two sets of codes in common use are.  

What is feed back control ? What is feed forward control ? Discuss its application ?

Description : What is feed back control ? What is feed forward control ? Discuss its application ?

Last Answer : Feed back control: Feed back control involves the detection of the controlled variable and counteracting of charges its it's value relative to set point, by adjustment of a manipulated ... controller for a particular process application, two factors time and gain must be considered.    

What is Furnace Draft control ?

Description : What is Furnace Draft control ? 

Last Answer : Balanced draft boilers are generally used negative furnace pressure. When both forced draft and induced draft are used together, at some point in the system the pressure will be the same as that of atmosphere. ... have is a very slight (about 0.1" H20 ) negative pressure of the top of furnace.  

What is the difference the a wheatstone bridge and a potentiometer ?

Description : What is the difference the a wheatstone bridge and a potentiometer ?

Last Answer : The difference between a potentiometer and a wheatstone bridge measuring instrument is that potentiometer is a voltage measuring instrument and wheatstone bridge is a current measuring instrument. 

What is the specialty of thermocouples lead wires ?

Description : What is the specialty of thermocouples lead wires ?

Last Answer : They should be of the same material as the thermocouple.  

What are skin temperature thermocouples ?

Description : What are skin temperature thermocouples ? 

Last Answer : Skin thermocouples are those which are directly connected to the process without any thermowell. Used for measuring the skin temperature of heaters furnaces, flue gas etc.  

What type of sensing element would you use to measure very low temperature ?

Description : What type of sensing element would you use to measure very low temperature ?

Last Answer : The sensing element used for measuring very low temperature is R. T. D. ( Resistance Temperature Detector )

How will you calibrate a temp. recorder using a potentiometer ?

Description : How will you calibrate a temp. recorder using a potentiometer ?

Last Answer : Connect the potentiometer output to the input of temp. recorder. 1. Connect the ( +ve ) to the ( +ve ) and ( -ve ) to the ( -ve ). 2. If ambient compensation is provided ... ambient temp. millvolts to the corr. input millvolts measured. Find out from the chart for the corresponding temperature. 

Why are Thermowells used ?

Description : Why are Thermowells used ?

Last Answer : In numerous application it is neither desirable nor practical to expose a temperature sensor directly to a process material. Wells are therefore used to protect against damage corrosion, erosion, abrasion and high pressure processes. A ... 3. Monel. 4. Alloy steal. 5. Hastelloy 'C'.

Why is a converter used in a temp. recorder ?

Description : Why is a converter used in a temp. recorder ? 

Last Answer : The converter is designed to convert D. C. input voltage into an A. C. input voltage proportional in amplitude to the input.  

What is burnout feature ? Explain.

Description : What is burnout feature ? Explain.

Last Answer : Burnout provides the warning feature of driving indicator the end of scale if the input circuit should open. A burnout resistor is provided which develops a voltage drop between the measuring circuit and the ... Upscale burnout : R value 10 M Downscale burnout : R value 2.2 M 

What is the constant voltage unit ?

Description : What is the constant voltage unit ?

Last Answer : The constant voltage circuit consists of a rectifier, CR, a filter capacitor C1, followed by two stages of zener regulation. Abridge configuration is provided to 1amp line voltage regulation ... , Thus variations. Resisters R2 and R3 form a bridge that any remoment line voltage effects. 

Draw a potentiometer temp. Measuring circuits and explain its?

Description : Draw a potentiometer temp. Measuring circuits and explain its?  

Last Answer : OPERATION : The input to the instrument is a measurement of some in the processes using a sensing element ( such as thermocouple ) or a device to produce direct voltage, which is the voltage (signal) ... to zero results ( null point ) the balancing ( servo motor is be longer driven )   

What is two wire and three wire R.T.D. system ?

Description : What is two wire and three wire R.T.D. system ?  

Last Answer : Two wire R .T .D. system : Two wire RTD system use for short distance like a compressor field local panel. Three wire System : Three wire system use for long distance coke a field to control Run. The third wire is used for compensation of lead wire resistance. 

What is Pt 100 mean. ?

Description : What is Pt 100 mean. ? 

Last Answer : Pt100 means 100 OHMS at 0'C for a platinum resistance bulb.  

Explain the working of an Enraf level gauge?

Description : Explain the working of an Enraf level gauge?

Last Answer : The Enraf precise level gauge are based on servo powered null-balance technique. A displacer serves as a continuous level sensing element. Principle: A displacer with a relative density higher than ... to a remote indicator of which the receiver motor drives a counter indicating level variation.  

How will you check zero of a level D.P. transmitter while is line ?

Description : How will you check zero of a level D.P. transmitter while is line ? 

Last Answer : ١. Close both the isolation valves. ٢. Open the vent valve on L.P. leg and H.P. leg drain. ٣. Check and adjust zero if necessary. 

How will you commission D.P. transmitter in field in pressurized vessel.

Description : How will you commission D.P. transmitter in field in pressurized vessel.

Last Answer : ١. Close both the isolation valves, Vent the H.P. side. ٢. Fill it with the sealing liquid. ٣. Open the L.P. side vent valve. ٤. Adjust zero with suppression spring. ٥. Close the L.P. side vent valve. ٦. Open both the isolation valves.  

What are the limitations of leveltrol ?

Description : What are the limitations of leveltrol ?

Last Answer : The limitations of a level control that it cannot be used for lengths more than 72 inches.  

What is the used of Suppression and elevation ?

Description : What is the used of Suppression and elevation ?  

Last Answer : Suppression and elevation are used on Level applications where (1) transmitters are not mounted on some level (2) Wet leg. i.e. condensable vapors are present.

What will happen if the displacer has a hole in it while in line ?

Description : What will happen if the displacer has a hole in it while in line ?  

Last Answer : The output will be minimum. 

What will happen if the displacer has fallen down while in line ?

Description : What will happen if the displacer has fallen down while in line ?

Last Answer : The output will be maximum. 

How will you calibrate a leveltrol in the field ?

Description : How will you calibrate a leveltrol in the field ?

Last Answer : Calculation # 1 If the calibrating liquid is water: Process Liquid Density / 1* Displacer height = mm of H2O. Calculation # 2 If the calibrating liquid is Other liquid: Process Liquid Density / ... gravity or span adjustment ( Electronic Level ). 6. Fill it up to 50 %, check linearity.  

What is interface level ? How do you calculate it ?

Description : What is interface level ? How do you calculate it ?  

Last Answer : When a vessel is filled with two liquids of two different specific gravities the level measurement refers to as interface level. DP = H ( D - d )   On a level set the difference of two specific gravities.   

How will you reverse an action of the leveltrol.?

Description : How will you reverse an action of the leveltrol.?  

Last Answer : The reversing are serves as motion take off arm from the torque tube. It is provided with a slot on each side of the center so that link can be connected either for reverse or direct action.

Explain the working an electronic leveltrol.

Description : Explain the working an electronic leveltrol. 

Last Answer : The variation in buoyancy resulting from a change in liquid level, varies the net weight of the displacer increasing or decreasing the load on the torque arm. This change is directly ... change proportional to the rotor displacement, which is converted and amplified to a D.C. current.