A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free.

A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively 

 (a) 10A, 7.07A (b) 5A, 10A (c) 5A, 7.07A (d) 7.07A, 5A
by

1 Answer

Answer :

A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively 5A, 7.07A

by

Related questions

A single phase fully controlled bridge converter supplies a load drawing constant and ripple free load current,

Description : A single phase fully controlled bridge converter supplies a load drawing constant and ripple free load current, if the triggering angle is 30o, the input power factor will be  (A) 0.65 (B) 0.78 (C) 0.85 (D) 0.866

Last Answer : A single phase fully controlled bridge converter supplies a load drawing constant and ripple free load current, if the triggering angle is 30o, the input power factor will be 0.78

Define given parameters and state their values for bridge rectifier (i) Ripple factor (ii) PIV of diode.

Description : Define given parameters and state their values for bridge rectifier (i) Ripple factor (ii) PIV of diode.

Last Answer : Ripple Factor: Ripple Factor is defined as the ratio of RMS value of the AC component of output to the DC or average value of the output. Mathematically it is expressed as, ( ... which appears across non-conducting reverse biased diode. (ii) PIV of diode for bridge rectifier-Vm

The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc

Description : The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be • 12.1 volt • 1.21 volt • 0.482 volt • 4.82 volt

Last Answer : The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be 12.1 volt

A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load

Description : A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load current of 10 A at a firing angle of 30o. The approximate Total harmonic Distortion (%THD) and the rms value of fundamental component ... (B) 31% and 7.8 A (C) 66% and 6.8 A (D) 66% and 7.8 A

Last Answer : A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load current of 10 A at a firing angle of 30o. The approximate Total harmonic Distortion (%THD) and the rms value of fundamental component of input current will respectively be 31% and 7.8 A

The ripple factor of a bridge rectifier is

Description : The ripple factor of a bridge rectifier is  1.0.48 2.0.812 3. 1.11 4. 1.21 

Last Answer : The ripple factor of a bridge rectifier is 0.48

In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output?

Description : In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output? (A) 30 Hz (B) 60 Hz (C) 20 Hz (D) 15 Hz

Last Answer : In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output? (A) 30 Hz (B) 60 Hz (C) 20 Hz (D) 15 Hz

Ripple factor for a half wave rectifier is ....

Description : Ripple factor for a half wave rectifier is  a. 1.65 b. 1.45 c. 1 d. 1.21 

Last Answer : Ripple factor for a half wave rectifier is 1.21

The input frequency is 50 Hz. The ripple frequency in a 12 phase full wave rectifier is

Description : The input frequency is 50 Hz. The ripple frequency in a 12 phase full wave rectifier is (A) 1200 Hz (B) 600 Hz (C) 100 Hz (D) 50 Hz 

Last Answer : The input frequency is 50 Hz. The ripple frequency in a 12 phase full wave rectifier is 1200 Hz

The dc current through each diode in a bridge rectifier equals : -

Description : The dc current through each diode in a bridge rectifier equals : - a) the load current b) half the dc load current c) twice the dc load current d) one-fourth the dc load current

Last Answer : The dc current through each diode in a bridge rectifier equals : - the load current

Ripple in output current of a step-down chopper feeding RLE load is maximum, when duty cycle is equal to:

Description : Ripple in output current of a step-down chopper feeding RLE load is maximum, when duty cycle is equal to:  (1) 1 (2) 0.5 (3) 0.75 (4) 0.33

Last Answer : Ripple in output current of step down Chopper feeding a RLE load is maximum, when duty cycle is equal to 0.5

The use of four diodes, in a full-wave bridge rectifier circuit, will __________. A. provide unidirectional current to the load B. allow a very high leakage current from the load C. convert direct current to alternating current D. offer high opposition to current in two directions

Description : The use of four diodes, in a full-wave bridge rectifier circuit, will __________. A. provide unidirectional current to the load B. allow a very high leakage current from the load C. convert direct current to alternating current D. offer high opposition to current in two directions

Last Answer : Answer: A

What is the ripple frequency of a full-wave rectifier with an input frequency of 60 Hz?

Description : What is the ripple frequency of a full-wave rectifier with an input frequency of 60 Hz?

Last Answer : 120 hertz.

What is the ripple frequency of a full-wave rectifier with an input frequency of 60 Hz?

Description : What is the ripple frequency of a full-wave rectifier with an input frequency of 60 Hz?

Last Answer : 120 hertz.

List out advantages and disadvantages of bridge rectifier.

Description : List out advantages and disadvantages of bridge rectifier.

Last Answer : Advantages :  1. Bridge rectifier can be used in applications allowing floating output terminals i.e. not output terminal is grounded.  2. The need of center-tapped transformer is eliminated.  ... The value of the diodes used should be precise , else there will be an error in rectification

What is the ripple factor of the rectifier?

Description : What is the ripple factor of the rectifier?

Last Answer : A4: The ripple factor of the rectifier: - Half wave recitifer:-1.21, Center tape wave rectifier:-0.48 Bridge full wave:-0.48

What is the Ripple frequency of a half-wave rectifier if the input frequency is 60 Hz?

Description : What is the Ripple frequency of a half-wave rectifier if the input frequency is 60 Hz?

Last Answer : 60 hertz.

Define following parameter of rectifier: (i) Ripple factor (ii) Efficiency (iii) Peak Inverse Voltage (iv) Transformer utilization factor

Description : Define following parameter of rectifier: (i) Ripple factor (ii) Efficiency (iii) Peak Inverse Voltage (iv) Transformer utilization factor

Last Answer : (i) Ripple Factor - Ripple factor (γ) may be defined as the ratio of the root mean square (rms) value of the ripple voltage to the absolute value of the DC component of the ... the same rectifier. Effective VA Rating of transformer is the average of primary and secondary VA rating of transformer.

Name the circuit used in rectifier to minimize ripple. List the types of this circuit with simple circuit diagram.

Description : Name the circuit used in rectifier to minimize ripple. List the types of this circuit with simple circuit diagram.

Last Answer : Rectifier filter is an electronic circuit that removes ripple or unwanted AC signal components from the output of a Rectifier. Types - (a) Series Inductor filter (d) Shunt capacitor filter (b) L-C type filter (e) Π - type filter

Define PIV, TUF, ripple factor, efficiency of rectifier.

Description : Define PIV, TUF, ripple factor, efficiency of rectifier.

Last Answer : PIV: Peak Inverse Voltage (PIV) is defined as the maximum negative voltage which appears across non-conducting reverse biased diode. TUF : Transformer Utilization Factor (TUF) is defined as the ratio of DC output ... Efficiency of rectifier: η = DC output power/ AC input power = PLdc / Pac

Define the term 'Ripple factor' for rectifier.

Description : Define the term 'Ripple factor' for rectifier.

Last Answer : Ripple factor: The ratio of RMS value of ac component present in the waveform to the dc component in the waveform is called as ripple factor.  OR  The unwanted AC components present in output waveform of a rectifier is called as ripple factor.

Single-phase mid-point controlled rectifier with RL load

Description : Single-phase mid-point controlled rectifier with RL load

Last Answer : Single-phase mid-point controlled rectifier with RL load : The circuit configuration of single-phase midpoint controlled rectifier is shown in the figure. During positive half-cycle of ... some part of next positive half-cycle of voltage with reversed polarity can appear across load.

Single-phase Midpoint controlled rectifier with Resistive load

Description : Single-phase Midpoint controlled rectifier with Resistive load

Last Answer : Single-phase Midpoint controlled rectifier with Resistive load:  1) During positive half cycle of AC supply, a is positive with respect to b , this makes T1 forward biased and T2 is reverse ... voltage reverses the polarity and T2 is turned off. The operation is as shown in waveforms.

A single phase, half-wave, controlled rectifier has 400 sin (314 t) as the input voltage and R as the load...

Description : A single phase, half-wave, controlled rectifier has 400 sin (314 t) as the input voltage and R as the load. For a firing angle of 60° for the SCR, the average output voltage is   (a) 240/π (b) 400/π (c) 300/π (d) 200/π 

Last Answer : C

For a diode to act as a rectifier, should it be connected in series or parallel with the load?

Description : For a diode to act as a rectifier, should it be connected in series or parallel with the load?

Last Answer : Series.

In a d.c. series motor, the torque developed is 20 Nm at 10A. If the load current is doubled, the new torque will be : -

Description : In a d.c. series motor, the torque developed is 20 Nm at 10A. If the load current is doubled, the new torque will be : -  a) 60 Nm b) 45 Nm c) 80 Nm d) 100 Nm

Last Answer : In a d.c. series motor, the torque developed is 20 Nm at 10A. If the load current is doubled, the new torque will be : - 80 Nm

A three phase transmission line delivers a load of 5 MW at 0.8 power factor lagging. Resistance of each...

Description : A three phase transmission line delivers a load of 5 MW at 0.8 power factor lagging. Resistance of each conductor is 0.5 ohm / km. Receiving end voltage is 33 kV. If the line loss is not to exceed 10%, determine the length of the line.  (A) 7 km (B) 27.9 km (C) 56.8 km (D) 13.9 km

Last Answer : B

A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and

Description : A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and is operating at a firing angle of 60o. The load current is assumed constant at 10 A due to high load inductance. The input ... 0.552 (C) IDF IPF = = 0.5; 0.478 (D) IDF IPF = = 0.5; 0.318 

Last Answer : A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and is operating at a firing angle of 60o. The load current is assumed constant at 10 A due to high ... (IDF) and the input power factor (IPF) of the converter will be IDF IPF = = 0.5; 0.478

Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Description : Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Last Answer : Single phase fully control bridge converter with RL load: 1. During positive half cycle of input voltage, T1 and T2 are forward biased and during negative half cycle, T3 and T4 are forward biased. Therefore, T1-T2 ... cycle till the firing of next pair of SCRs as shown in the waveform.

A single phase full-wave half-controlled bridge converter feeds an inductive load. The two SCRs in the

Description : A single phase full-wave half-controlled bridge converter feeds an inductive load. The two SCRs in the converter are connected to a common DC bus. The converter has to have a freewheeling diode.  (A) ... to one of the SCRs is missed, it will subsequently cause a high load current in the other SCR.

Last Answer : A single phase full-wave half-controlled bridge converter feeds an inductive load. The two SCRs in the converter are connected to a common DC bus. The converter has to have a freewheeling diode. because the converter does not provide for free-wheeling for high values of triggering angles

Define ripple factor and PIV of diode.

Description : Define ripple factor and PIV of diode.

Last Answer : 1. Ripple factor: It is define as ratio of R.M.S. value of AC component to the DC component in the output.  2. PIV : It is maximum reverse voltage that diode can withstand without destroying junction.

In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

Description : In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

Last Answer : In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage decreases

The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Description : The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Last Answer : Answer: A

When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a

Description : When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is

Last Answer : When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is √3/2

A dc cumulatively compounded motor delivers rated load torque at rated speed. If series field is short circuited, then the armature current and speed will a) Both increases b) Both decreases c) Increases and decreases d) Decreases and increases

Description : A dc cumulatively compounded motor delivers rated load torque at rated speed. If series field is short circuited, then the armature current and speed will a) Both increases b) Both decreases c) Increases and decreases d) Decreases and increases

Last Answer : Ans: Both increases

The ripple content of load current of a converter feeding RL load is decided by

Description : The ripple content of load current of a converter feeding RL load is decided by  A) Load resistance alone B) Load inductance alone C) Both load resistance and load inductance D) Neither resistance nor inductance

Last Answer : The ripple content of load current of a converter feeding RL load is decided by Both load resistance and load inductance

What are the advantages of free wheeling diode in rectifier circuit?

Description : What are the advantages of free wheeling diode in rectifier circuit?

Last Answer : The input power factor is improved. It prevents the output voltage from becoming negative. Load current waveform is improved.

The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a

Description : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) ... proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

Last Answer : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ directly proportional to α and inversely proportional to Φ

In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load,

Description : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is (A) sinusoidal current (B) constant dc current (C) continuous rectangular pulses (D) alternating rectangular pulses

Last Answer : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is alternating rectangular pulses

The correct term for the illustrated circuit is a ________. EL-0063 A. single phase half wave high power rectifier B. three phase half wave rectifier C. three phase full wave rectifier D. a single phase full wave rectifier

Description : The correct term for the illustrated circuit is a ________. EL-0063 A. single phase half wave high power rectifier B. three phase half wave rectifier C. three phase full wave rectifier D. a single phase full wave rectifier

Last Answer : Answer: C

When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?

Description : When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?

Last Answer : Feel Free to Answer

What effect does an open diode have on the output voltage of a half wave rectifier and on a full wave rectifier?

Description : What effect does an open diode have on the output voltage of a half wave rectifier and on a full wave rectifier?

Last Answer : An open diode will result in no output from a half waverectifier, and an open diode will cut the output of a full waverectifier in half.

One diode of a full-wave rectifier has burned out in a shorted condition. Therefore, the output will be ____________. A. zero B. a rectified half-wave C. a rectified full-wave D. equal to the AC input

Description : One diode of a full-wave rectifier has burned out in a shorted condition. Therefore, the output will be ____________. A. zero B. a rectified half-wave C. a rectified full-wave D. equal to the AC input

Last Answer : Answer: D

A full-wave rectifier has one diode burned out in an open condition, what will be the output characteristic of the device? A. Zero B. Half-wave rectified C. Full-wave rectified D. Equal to the AC input

Description : A full-wave rectifier has one diode burned out in an open condition, what will be the output characteristic of the device? A. Zero B. Half-wave rectified C. Full-wave rectified D. Equal to the AC input

Last Answer : Answer: B

In the illustrated motor controller, the motor fails to start. A voltmeter reading between 1 and 6 reads line voltage, while the voltmeter reading between 2 and 6 reads 0 VAC. The problem is __________. EL-0007 A. the control fuse is the wrong amperage not allowing full current to pass through B. the stop switch is open C. an open in the 'M' coil, 'Ma' contact/start switch or overload contacts D. fuse '10a' is blown

Description : In the illustrated motor controller, the motor fails to start. A voltmeter reading between 1 and 6 reads line voltage, while the voltmeter reading between 2 and 6 reads 0 VAC. The problem is __________. EL- ... in the 'M' coil, 'Ma' contact/start switch or overload contacts D. fuse '10a' is blown

Last Answer : Answer: B

Each flip-flop in a 4-bit ripple counter introduces a maximum delay of 40 n sec. The maximum clock frequency

Description : Each flip-flop in a 4-bit ripple counter introduces a maximum delay of 40 n sec. The maximum clock frequency is (a) 2.65 MHz (b) 6.25 MHz (c) 5.26 MHz (d) 6.52 MHz 

Last Answer : Each flip-flop in a 4-bit ripple counter introduces a maximum delay of 40 ns. The maximum clock frequency is 6.25MHz. nff  * Tdelay = 4*40 =160ns so, max. frequency = 1/ (200*10-9 ) = 6.25MHz          

The ripple factor in an LC filter.

Description : The ripple factor in an LC filter.   (A) Increases with the load current (B) Increases with the load resistance (C) Remains constant with the load current (D) Has the lowest value

Last Answer : The ripple factor in an LC filter. Has the lowest value

In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system

Description : In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: (1) 400 Hz (2) 800 Hz (3) 1200 Hz (4) None of these

Last Answer : In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: 1200 Hz

Full wave bridge rectifier?

Description : Full wave bridge rectifier?

Last Answer : Full wave bridge rectifier: In full wave bridge rectifiers 4 diodes are using. During positive half cycle, D1 and D4 are in forward biased condition. In the negative half cycle of ac D3 and D2 ... a centre tap rectifier. But it requires more number of diodes than centre tap and half wave rectifiers

Why we are using the bridge rectifier in most of the circuits instead of full wave rectifier eventhough the output of both are same?

Description : Why we are using the bridge rectifier in most of the circuits instead of full wave rectifier eventhough the output of both are same?

Last Answer : Ans-In bridge type (FWR) rectifiers center tapping transformer are not required so small transformers are used and we will get twice of the out put voltage that of the center tapped FWR.

What main advantage does a bridge rectifier have over a conventional full-wave rectifier?

Description : What main advantage does a bridge rectifier have over a conventional full-wave rectifier?

Last Answer : The bridge rectifier can produce twice the voltage with the same size transformer.