What type of amplifier would be used to amplify the signal from a radio antenna?

What type of amplifier would be used to amplify the signal  from a radio antenna?
by

1 Answer

Answer :

An rf voltage amplifier.
by

Related questions

Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Description : Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Last Answer : B. Antenna

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna compared to the output power of the transmitter C. The ratio of the signal in the backward direction D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Description : What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna ... D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Last Answer : D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

In a logic circuit, the NOT gate function _____________. A. does not alter a logical input B. serves to amplify a given signal level C. must be accomplished with a common collector transistor arrangement D. reverses an input logic condition

Description : In a logic circuit, the NOT gate function _____________. A. does not alter a logical input B. serves to amplify a given signal level C. must be accomplished with a common collector transistor arrangement D. reverses an input logic condition

Last Answer : Answer: D

The common-emitter transistor circuit can amplify a small current signal because a small change in the signal current produces one of the following. Does the change in signal produce a large change in the: w) emitter-base voltage x) base current y) collector current z) collector voltage

Description : The common-emitter transistor circuit can amplify a small current signal because a small change in the signal current produces one of the following. Does the change in signal produce a large change in the: w) emitter-base voltage x) base current y) collector current z) collector voltage

Last Answer : ANSWER: Y -- COLLECTOR CURRENT

What type of transmission is radiated from an aircraft’s radio altimeter antenna? A. An amplitude modulated continuous wave B. A pulse position modulated UHF signal C. A differential phase shift keyed UHF signal D. A frequency modulated continuous wave

Description : What type of transmission is radiated from an aircraft’s radio altimeter antenna? A. An amplitude modulated continuous wave B. A pulse position modulated UHF signal C. A differential phase shift keyed UHF signal D. A frequency modulated continuous wave

Last Answer : D. A frequency modulated continuous wave

What components form the input-signal-developing impedance for the amplifier?

Description : What components form the input-signal-developing impedance for the amplifier?

Last Answer : C2 and the secondary of T1.

If the input-signal-developing impedance of an amplifier is increased, what is the effect on the gain?

Description : If the input-signal-developing impedance of an amplifier is increased, what is the effect on the gain?

Last Answer : The gain increases.

In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?

Description : In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?

Last Answer : 0 volts.

If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?

Description : If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?

Last Answer : 200 millivolts. A-18. a. Differential amplifier

If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?

Description : If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?

Last Answer : . A different shape than the input signals but larger in amplitude.

If only one input signal is used with a difference amplifier, what will the output signal be?

Description : If only one input signal is used with a difference amplifier, what will the output signal be?

Last Answer : Equal in shape and frequency to the input signal; larger in amplitude than the input signal; half as large in amplitude as when two input signals were used that were 180 degrees out of phase.

If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?

Description : If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?

Last Answer : Equal in shape and frequency to each input signal and larger in amplitude by two times than

. If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?

Description : . If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?

Last Answer : No output (the signals will "cancel out").

When a large signal and a small signal are applied to a lin log amplifier at the same time, what is the effect on the small signal?

Description : When a large signal and a small signal are applied to a lin log amplifier at the same time, what is the effect on the small signal?

Last Answer : Amplification is reduced.

In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal? In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal?

Description : In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal?

Last Answer : Local oscillator and coherent oscillator.

What is the primary difference between the pump signal of a simple parametric amplifier and the pump signal of a nondegenerative parametric amplifier?

Description : What is the primary difference between the pump signal of a simple parametric amplifier and the pump signal of a nondegenerative parametric amplifier?

Last Answer : The pump signal of a nondegenerative parametric amplifier is higher than twice the input signal.

The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?

Description : The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?

Last Answer : Exactly double the input frequency.

Does an amplifier actually change an input signal? Why or why not?

Description : Does an amplifier actually change an input signal? Why or why not?

Last Answer : No, the input signal is unchanged, the output signal is controlled by the input signal but does not effect the actual input signal.

What connecting link is used to transfer energy from a radio transmitter to its antenna located on

Description : What connecting link is used to transfer energy from a radio transmitter to its antenna located on

Last Answer : Transmission line.

If a transmitting antenna is placed close to the ground, how should the antenna be polarized to give the greatest signal strength?

Description : If a transmitting antenna is placed close to the ground, how should the antenna be polarized to give the greatest signal strength?

Last Answer : Vertically polarized.

Radio wave concentration in the direction of the signal emitted by a directional antenna. A. Back lobe radiation B. Side lobe radiation C. Major lobe radiation D. Transmitted signal

Description : Radio wave concentration in the direction of the signal emitted by a directional antenna. A. Back lobe radiation B. Side lobe radiation C. Major lobe radiation D. Transmitted signal

Last Answer : C. Major lobe radiation

An automobile needs an antenna for its radio to play properly because: w) the automobile's tires insulate it from the ground. x) the automobile's body acts as a Faraday cage. y) when the automobile moves, the velocity of the radio signal appears changed with respect to when it is at rest. z) the transmitter also uses an antenna.

Description : An automobile needs an antenna for its radio to play properly because: w) the automobile's tires insulate it from the ground. x) the automobile's body acts as a Faraday cage. y) when the ... signal appears changed with respect to when it is at rest. z) the transmitter also uses an antenna.

Last Answer : ANSWER: X -- THE AUTOMOBILE'S BODY ACTS AS A FARADAY CAGE. 

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Description : What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Last Answer : A. The power traveling from the transmitter to the antenna.

What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Description : What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Last Answer : C. Local oscillator, mixer and RF amplifier

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Description : Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Last Answer : D. Local oscillator

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

What do you call the single booster installed on the antenna dish of satellite receiver? A. Low noise amplifier B. Single amplifier C. Noise amplifier D. Rectifier

Description : What do you call the single booster installed on the antenna dish of satellite receiver? A. Low noise amplifier B. Single amplifier C. Noise amplifier D. Rectifier

Last Answer : A. Low noise amplifier

How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator or ferrite isolator in the feed line of the transmitter and duplexer C. By using a class C final amplifier with high driving power D. By installing a low-pass filter in the antenna feed line

Description : How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator ... high driving power D. By installing a low-pass filter in the antenna feed line

Last Answer : A. Through installing a band-pass filter in the antenna feed line

One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Description : One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Last Answer : d. To prevent reradiation of the local oscillator

If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?

Description : If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?

Last Answer : A step-down transformer.

What type of klystron is used as the final stage of a power- amplifier transmitter?

Description : What type of klystron is used as the final stage of a power- amplifier transmitter?

Last Answer : Multicavity klystron.

What type of klystron is used as the final stage of a power- amplifier transmitter?

Description : What type of klystron is used as the final stage of a power- amplifier transmitter?

Last Answer : Multicavity klystron.

What type coupling would be most useful for an audio amplifier between the first and second stages?

Description : What type coupling would be most useful for an audio amplifier between the first and second stages?

Last Answer : RC coupling.

What type coupling is usually used to couple the output from a power amplifier?

Description : What type coupling is usually used to couple the output from a power amplifier?

Last Answer : Transformer coupling.

What type of amplifier would be used to drive the speaker system of a record player?

Description : What type of amplifier would be used to drive the speaker system of a record player?

Last Answer : An audio power amplifier.

Does wearing a hat amplify your chances of loosing your hair?

Description : Does wearing a hat amplify your chances of loosing your hair?

Last Answer : In my case, I have always worn hats, including at work, and am now very shiny on top. but I blame it on the vasectomy

Im trying to amplify my wireless with my mac mini downstairs,but i dont know how.

Description : Im trying to amplify my wireless with my mac mini downstairs,but i dont know how.

Last Answer : Well, let's assume that it isn't the mac screwing up. The only thing I can think of to recommend is buying an Airport Express and plugging it closer to your Mac Mini, the only problem is, you ... far away is the mini from the router and how many walls\ceilings does the signal have to pass through?

What is Amplify ?

Description : What is Amplify ?

Last Answer : Amplify .

How To Use Wire Shelving to Amplify Space in a Child’s Closet?

Description : How To Use Wire Shelving to Amplify Space in a Child’s Closet?

Last Answer : Most standard children's bedroom closets contain one shelf andone hanging bar, which is not a good use of space. In a closet suchas this, it is easy for a small space to quickly become ... width, depth, and height anddraw a diagram of the closet on paper to decide where wire shelvingis nee

How much can I amplify my speakers without breaking them?

Description : How much can I amplify my speakers without breaking them?

Last Answer : When it comes to amplifying your speakers without blowing them it all depends really on what kind of speakers they are . Usually you can only put them mid way without blowing them completly , as having them on high on the time will completely destroy them in no time .

Why are vacuum tubes also called valves? A) Because they can amplify the weak signals and make them strong B) Because they can stop or allow the flow of current C) Both of above D) None of above

Description : Why are vacuum tubes also called valves? A) Because they can amplify the weak signals and make them strong B) Because they can stop or allow the flow of current C) Both of above D) None of above

Last Answer : Answer : B

Yeast artificial chromosome can be used to amplify DNA sequences of the size (A) Upto 10 kb (B) Upto 45 kb (C) Upto 100 kb (D) Upto 1,000 kb

Description : Yeast artificial chromosome can be used to amplify DNA sequences of the size (A) Upto 10 kb (B) Upto 45 kb (C) Upto 100 kb (D) Upto 1,000 kb

Last Answer : Answer : D

Twenty cycles of PCR can amplify DNA: (A) 220 fold (B) 202 fold (C) 20 x 2 fold (D) 20 fold

Description : Twenty cycles of PCR can amplify DNA: (A) 220 fold (B) 202 fold (C) 20 x 2 fold (D) 20 fold

Last Answer : Answer : A

Polymerase chain reaction can rapidly amplify DNA sequences of the size (A) Upto 10 kilobases (B) Upto 45 kilobases (C) Upto 100 kilobases(D) Upto 1,000 kilobases

Description : Polymerase chain reaction can rapidly amplify DNA sequences of the size (A) Upto 10 kilobases (B) Upto 45 kilobases (C) Upto 100 kilobases(D) Upto 1,000 kilobases

Last Answer : Answer : A

What is the device used in fiber optic communication which consist of a receiver transmitter use to clean up and amplify digital data moving in one direction and another in the opposite direction? A. Optic compressors B. Optic retarders C. Optic isolator D. Optic regenerators

Description : What is the device used in fiber optic communication which consist of a receiver transmitter use to clean up and amplify digital data moving in one direction and another in the opposite direction? A. Optic compressors B. Optic retarders C. Optic isolator D. Optic regenerators

Last Answer : D. Optic regenerators