Which edges of the pulse can be modulated in pulse duration modulation?

1 Answer

Answer :

Either, or both at the same time.

Related questions

Description : ECE Board Exam March 1996 One type of pulse communications system uses pulse that appear as a group, and which vary in number according to the loudness of the voice. This type of ... A. pulse duration modulation B. pulse amplitude modulation C. pulse code modulation D. pulse position modulation

Last Answer : A. pulse duration modulation

Description : What is the primary advantage of pulse-modulation systems?

Last Answer : . Low susceptibility to noise.

Description : Pulse-code modulation requires the use of approximations of value that are obtained by what process?

Last Answer : Quantization.

Description : What is pulse-frequency modulation?

Last Answer : A method of pulse modulation in which a modulating wave is used to frequency modulate a pulse-generating circuit

Description : What is the main disadvantage of pulse-position modulation?

Last Answer : It requires synchronization between the transmitter and receiver.

Description : What characteristics of a pulse can be changed in pulse time modulation?

Last Answer : The time duration of the pulses or the time of occurrence of the pulses.

Description : What, if any, noise susceptibility advantage exists for pulse-amplitude modulation over analog amplitude modulation?

Last Answer : Both are susceptible to noise and interference

Description : To ensure the accuracy of a transmission, what is the minimum number of times a modulating wave should be sampled in pulse modulation?

Last Answer : 2.5 times the highest modulating frequency.

Description : What action is necessary to impress intelligence on the pulse train in pulse modulation?

Last Answer : Some characteristic of the pulses has to be varied.

Description : If the length of the fiber point defect changes with pulse duration, is the OTDR signal deviation a point defect or a region of high fiber attenuation?

Last Answer : A point defect.

Description : What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Last Answer : B. The ratio between the deviation of a frequency modulated signal and the modulating frequency.

Description : A modulation which does not follow the sine wave pattern, it produces undesirable harmonics such as spurious emission A. 0% modulated B. Over-modulated C. Unmodulated D. 100% modulated

Last Answer : B. Over-modulated

Description : In amplitude modulation technique the unmodulated carrier is referred to as having ______. A. 100% modulation B. 0% modulation C. 50% modulated D. Over modulated

Last Answer : B. 0% modulation

Description : Modulation in which the modulated wave is always present. A. Carrier modulation B. Front-end C. Continuous modulation D. Log-periodic modulation

Last Answer : C. Continuous modulation

Description : The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the ... . Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Last Answer : D. Residual noise level

Description : In frequency modulation, amplitude of modulated wave is A. positive B. negative C. constant D. zero

Last Answer : constant

Description : Inan HFC network, the upstream data are modulated using the _______ modulation technique. A) QAM B) QPSK C) PCM D) ASK

Last Answer : QPSK

Description : Inan HFC network, the downstream data are modulated using the _______ modulation technique. A) PSK B) QAM C) PCM D) ASK

Last Answer : QAM

Description : The amplifiers following the modulated stage in a low level modulation AM system be  (A) linear amplifier (B) harmonic generators (C) class C power amplifiers (D) class untuned amplifiers

Last Answer : The amplifiers following the modulated stage in a low level modulation AM system be class C power amplifiers

Description : If the carrier of a 100 percent modulation modulated AM wave is suppressed, the percentage power saving will be (A) 50.55 (B) 15.55 (C) 10.66 (D) 66.66

Last Answer : If the carrier of a 100 percent modulation modulated AM wave is suppressed, the percentage power saving will be 66.66

Description : What type of transmission is radiated from an aircraft’s radio altimeter antenna? A. An amplitude modulated continuous wave B. A pulse position modulated UHF signal C. A differential phase shift keyed UHF signal D. A frequency modulated continuous wave

Last Answer : D. A frequency modulated continuous wave

Description : How is a beam of electrons velocity-modulated?

Last Answer : By alternately speeding up or slowing down the electrons

Description : For AM transmissions, the carrier is normally modulated within what range?

Last Answer : 60% to 95%.

Description : Why can phase-modulated signals be detected by fm detectors?

Last Answer : Because of the incidental frequency shift that is caused while phase-shifting a carrier wave that is similar to fm modulation.

Description : Where is the intelligence contained in a phase-modulated signal?

Last Answer : In the amount and rate of phase shift of the carrier wave.

Description : What is pulse-width modulation (PWM) in Arduino?

Last Answer : Pulse-width modulation (PWM) in Arduino is a technique used to control the brightness of an LED or the speed of a motor by varying the duty cycle of a digital signal.

Description : What is a pulse-width modulation (PWM) signal in Arduino?

Last Answer : A PWM signal in Arduino is a digital signal that varies the width of the pulse to simulate an analog signal.

Description : A technique used by codes to convert an analog signal into a digital bit stream is known as A) Pulse code modulation B) Pulse stretcher C) Query processing D) Queue management

Last Answer : Answer : A

Description : Type of modulation used in TV broadcast visual transmitter. A. Pulse modulation B. DSBFC C. Vestigial sideband D. SSBFC

Last Answer : C. Vestigial sideband

Description : Which of the following systems is not used in radio detection and ranging? A. Frequency shift B. Frequency modulation C. Pulse radar D. Amplitude modulation

Last Answer : D. Amplitude modulation

Description : Modulation in which no signal is present between pulses A. Pulse modulation B. QAM C. PSK D. FSK

Last Answer : A. Pulse modulation

Description : ECE Board Exam March 1996 Which of the following pulse modulation systems is analog? A. Delta B. Differential PCM C. PWM D. PCM

Last Answer : C. PWM

Description : ECE Board Exam March 1996 The modulation system used for telegraphy is A. frequency-shift keying B. two-tone modulation C. pulse-code modulation D. single-tone modulation

Last Answer : A. frequency-shift keying

Description : What is Pulse Width Modulation?

Last Answer : Ans-Pulse width modulation is a modulation technique in which the width of the pulse is varied in accordance with the message signal. Pulse width Modulation is abbreviated as PWM. PWM can be used ... the pulse train and recover an average analog waveform. PWM is used in sound synthesis circuits.

Description : Pulse width modulation may be generated:

Last Answer : with a monostable multivibrator

Description : A pulse modulation technique as the width of a constant amplitude pulse is varied proportional to the amplitude of the analog signal at the time the signal is sampled.

Last Answer : PWM, PLM, PDM

Description : Pulse – amplitude modulation signals are multiplexed by using

Last Answer : FET switches

Description : A technique used by codes to convert an analog signal into a digital bit stream is known as a. Pulse code modulation b. Pulse stretcher c. Query processing d. Queue management

Last Answer : a. Pulse code modulation

Description : A technique used by codes to convert an analog signal into a digital bit stream is known as a. Pulse code modulation b. Pulse stretcher c. Query processing d. Queue management

Last Answer : a. Pulse code modulation

Description : A technique used by codes to convert an analog signal into a digital bit stream is known as a. Pulse code modulation b. Pulse stretcher c. Query processing d. Queue management

Last Answer : a. Pulse code modulation

Description : Define pulse modulation. State its types. 

Last Answer : Pulse Modulation - consists essentially of sampling analog information signals and then converting those samples into discrete pulses. OR It consists essentially of sampling analog information signals and then converting those ... PAM - PWM - PPM  ii) Digital Pulse Modulation - PCM - DM - ADM 

Description : Indicate which of the following pulse modulation is analog  a) PCM b) DPCM c) PWM d) Delta

Last Answer : Indicate which of the following pulse modulation is analog  a) PCM b) DPCM c) PWM d) Delta

Description : In single pulse modulation of PWM inverters, third harmonic can be eliminated if pulse width is equal to   (a) 30o (b) 60o (c) 120o (d) 150o

Last Answer : In single pulse modulation of PWM inverters, third harmonic can be eliminated if pulse width is equal to 120o

Last Answer : PWM means the width of pulse signal can be varied by varying ton & tOFF.

Description : Which cavity of a three-cavity klystron causes most of the velocity modulation?

Last Answer : The middle cavity.

Description : What can be added to the basic two-cavity klystron to increase the amount of velocity modulation and the power output?

Last Answer : Intermediate cavities between the input and output cavities.

Description : What types of modulation are shipboard receive-only equipment designed to receive?

Last Answer : Fm or psk.

Description : What type of modulation do most analog fiber optic communications systems use?

Last Answer : Intensity modulation.

Description : Define modulation.

Last Answer : The process of varying one or more characteristics of an optical signal to encode and convey information.

Description : Which junction of the transistor in the common-emitter detector detects the modulation envelope?

Last Answer : Emitter-base junction