Why is a multimeter preferred over separate meters?

Why is a multimeter preferred over separate meters?
by

1 Answer

Answer :

It is much more convenient to have one meter with several  functions than several meters each with a single function.
by

Related questions

How is an overload condition indicated by the electronic digital multimeter?

Description : How is an overload condition indicated by the electronic digital multimeter?

Last Answer : Simultaneous flashing of display readouts

Power for the electronic digital multimeter is normally supplied by what internal power source?

Description : Power for the electronic digital multimeter is normally supplied by what internal power source?

Last Answer : Rechargeable batteries.

What type of circuit breaker is used on a multimeter?

Description : What type of circuit breaker is used on a multimeter?

Last Answer : A push button or push-pull circuit breaker (small size, low power).

What meter reading is shown on each multimeter in each part of figure 1-50?

Description : What meter reading is shown on each multimeter in each part of figure 1-50?

Last Answer : (A) 410 mA dc; (B) 3.9 mA ac; (C) -22 V dc; (D) 600 V ac; (E) 1.4 V ac; (F) 1.9 kohms

Why would you use a hook-on voltmeter instead of a multimeter?

Description : Why would you use a hook-on voltmeter instead of a multimeter?

Last Answer : To measure current safely and easily (with no need to disconnect the wiring of the circuit).

How is the mirror on a multimeter used?

Description : How is the mirror on a multimeter used?

Last Answer : Make sure no image of the pointer is visible in the mirror when reading the meter.

What is the reason for having a mirror on the scale of a multimeter?

Description : What is the reason for having a mirror on the scale of a multimeter?

Last Answer : To stop parallax error

Why is the dc scale on a multimeter different than the ac scale?

Description : Why is the dc scale on a multimeter different than the ac scale?

Last Answer : The meter movement reacts to average ac voltage and current and the effective value is desired.

How is a multimeter changed from a voltage measuring device to a resistance measuring device?

Description : How is a multimeter changed from a voltage measuring device to a resistance measuring device?

Last Answer : By changing the position of the function switch

What is a multimeter?

Description : What is a multimeter?

Last Answer : . A single measuring device capable of performing the functions of a dc voltmeter and ammeter, an ac voltmeter and ammeter, and an ohmmeter

Why are LEDs preferred over laser diodes for low- and moderate-frequency analog applications?

Description : Why are LEDs preferred over laser diodes for low- and moderate-frequency analog applications?

Last Answer : LEDs require less complex circuitry than lasers.

Why are drum-type armatures preferred over the Gramme ring armature in modern dc generators?

Description : Why are drum-type armatures preferred over the Gramme ring armature in modern dc generators?

Last Answer : Drum-type armatures are more efficient, because flux lines are cut by both sides of each coil.

What is the advantage of using in-line wattmeters over output power meters?

Description : What is the advantage of using in-line wattmeters over output power meters?

Last Answer : Most in-line wattmeters are capable of measuring both forward and reflected power.

If a transmitting antenna is 100 meters high and a separate receiving antenna is 64 meters high, what is the maximum space wave communication distance possible between them? A. 18 km B. 72 km C. 164 km D. 656 km

Description : If a transmitting antenna is 100 meters high and a separate receiving antenna is 64 meters high, what is the maximum space wave communication distance possible between them? A. 18 km B. 72 km C. 164 km D. 656 km

Last Answer : B. 72 km

Why is flat tape preferred instead of round cord when wire bundles are laced?

Description : Why is flat tape preferred instead of round cord when wire bundles are laced?

Last Answer : Round cord has a tendency to cut into the wire insulation.

What is the preferred method for stripping wire?

Description : What is the preferred method for stripping wire?

Last Answer : By use of a wire-stripping tool

What type of deflection is preferred for a crt electron beam?

Description : What type of deflection is preferred for a crt electron beam?

Last Answer : . Electromagnetic.

Which types of LEDs are the preferred optical sources for short-distance, low-data-rate fiber optic systems?

Description : Which types of LEDs are the preferred optical sources for short-distance, low-data-rate fiber optic systems?

Last Answer : SLEDs and ELEDs.

What is the preferred method of repairing cracked runs on boards?

Description : What is the preferred method of repairing cracked runs on boards?

Last Answer : Clinched staple.

Extrinsic (OH) absorption peaks define three regions or windows of preferred operation. List the three windows of operation.

Description : Extrinsic (OH) absorption peaks define three regions or windows of preferred operation. List the three windows of operation.

Last Answer : The first, second, and third windows of operation are 850 nm, 1300 nm, and 1550 nm, respectively.

What is the most preferred method of troubleshooting?

Description : What is the most preferred method of troubleshooting?

Last Answer : Testing components by comparison

A station is known to operate at 60-meters. What is the frequency of the unknown station?

Description : A station is known to operate at 60-meters. What is the frequency of the unknown station?

Last Answer : 5 megahertz.

In reference to dB meters, 0 dBm represents 1 milliwatt into what value of load?

Description : In reference to dB meters, 0 dBm represents 1 milliwatt into what value of load?

Last Answer : 600-ohm load.

What do impedance-angle meters and vector bridges have in common?

Description : What do impedance-angle meters and vector bridges have in common?

Last Answer : Both measure phase angle and magnitude in determining impedance.

What are two types of frequency meters?

Description : What are two types of frequency meters?

Last Answer : Vibrating reed and moving disk.

Why is in-circuit meters used?

Description : Why is in-circuit meters used?

Last Answer : In-circuit meters are used to monitor the operation of electrical or electronic devices.

What two types of meters can be used to check a switch?

Description : What two types of meters can be used to check a switch?

Last Answer : An ohmmeter and a voltmeter.

What meters operate from their own power sources?

Description : What meters operate from their own power sources?

Last Answer : Self-excited.

What meters operate from their own power sources?

Description : What meters operate from their own power sources?

Last Answer : Self-excited.

What is the device called that will separate alternating current from direct current, or that will separate alternating current of one frequency from other alternating currents of different frequencies?

Description : What is the device called that will separate alternating current from direct current, or that will separate alternating current of one frequency from other alternating currents of different frequencies?

Last Answer : A filter.

What type of MOSFET can be independently controlled by two separate signals?

Description : What type of MOSFET can be independently controlled by two separate signals?

Last Answer : The dual-gate MOSFET.

A monopulse receiver has how many separate channels?

Description : A monopulse receiver has how many separate channels?

Last Answer : Three.

How can I use a multimeter to find out how many OHMS are in a cable?

Description : How can I use a multimeter to find out how many OHMS are in a cable?

Last Answer : Measure the potential difference (V) across the cable and the current (I) running through it. Then use Ohm’s law: V = IR. R is the resistance, given in ohms, where 1 ohm is 1 volt divided by 1 amp.

What is a multimeter ?

Description : What is a multimeter ?

Last Answer : Also known as Multimeter or Multitester , Avometer ( AVO {Ampere-Volt-Ohm} meter) . It is an electronic measuring instrument , where various measurement functions are combined in one unit. A simple ... টাকার 600 , and laboratory-grade models with certified grading can cost up to ইউ 5,000.

What inspection checks should be made to a multimeter before use?

Description : What inspection checks should be made to a multimeter before use?

Last Answer : If it has battery cells, ensure you have the good battery cells.The probes should be intact. The knobs should be in order. Thedevice should not have any cracks or broken parts.

What should be the outputs of the hot neutral and ground wires respectively when tested with a multimeter?

Description : What should be the outputs of the hot neutral and ground wires respectively when tested with a multimeter?

Last Answer : Feel Free to Answer

A multimeter is used to measure – (1) current (2) voltage (3) resistance (4) All of the above

Description : A multimeter is used to measure – (1) current (2) voltage (3) resistance (4) All of the above

Last Answer : (4) All of the above Explanation: A multimeter or a multitester, also known as a VOM (Volt-Ohm meter), is an electronic measuring instrument that combines several measurement functions in ... or digital circuits-analog multimeters (AMM) and digital multimeters (often abbreviated DMM or DVOM.)

If your multimeter gives a reading in ohms when testing each end of each conductor of a three-conductor cable, this indicates ______________. A. continuity of the conductor B. an infinite resistance C. the presence of a partial ground D. that the conductor is not short circuited

Description : If your multimeter gives a reading in ohms when testing each end of each conductor of a three-conductor cable, this indicates ______________. A. continuity of the conductor B. an infinite resistance C. the presence of a partial ground D. that the conductor is not short circuited

Last Answer : Answer: A

When reading AC current with the multimeter shown in the illustration and you are unsure of the range, the range switch should be set to ___________. EL-0047 A. 10 MA/ 10 AMP with leads in the (-10 A) and (+10 A) jacks B. 10 MA/ 10 AMP with leads in the (-COMMON) and (+) jacks C. 10 MA/ 10 AMP with leads in the (-COMMON) and (+10 A) jacks D. unable to measure AC current with this multimeter

Description : When reading AC current with the multimeter shown in the illustration and you are unsure of the range, the range switch should be set to ___________. EL-0047 A. 10 MA/ 10 AMP with leads in the (-10 A ... leads in the (-COMMON) and (+10 A) jacks D. unable to measure AC current with this multimeter

Last Answer : Answer: D

What is the resistance value indicated on the multimeter scale illustrated, if the range switch is set at R X 100, and the needle is at the position indicated by the letter 'R'? EL-0047 A. 6.0 ohms B. 162.5 ohms C. 600 ohms D. 16,250 ohms

Description : What is the resistance value indicated on the multimeter scale illustrated, if the range switch is set at R X 100, and the needle is at the position indicated by the letter 'R'? EL-0047 A. 6.0 ohms B. 162.5 ohms C. 600 ohms D. 16,250 ohms

Last Answer : Answer: C

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 100, and the needle is at the position indicated by the letter 'Y'? EL-0047 A. 220 ohms B. 240 ohms C. 2,400 ohms D. 24,000 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 100, and the needle is at the position indicated by the letter 'Y'? EL-0047 A. 220 ohms B. 240 ohms C. 2,400 ohms D. 24,000 ohms

Last Answer : Answer: C

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'A'? EL-0047 A. 10 ohms B. 100 ohms C. 200 ohms D. 1,000 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'A'? EL-0047 A. 10 ohms B. 100 ohms C. 200 ohms D. 1,000 ohms

Last Answer : Answer: C

A multimeter can be used to directly measure _____________. A. watts B. field flux C. current D. all of the above

Description : A multimeter can be used to directly measure _____________. A. watts B. field flux C. current D. all of the above

Last Answer : Answer: C

D.C. propulsion motor brush pressure depends on the brush grade used and in practice is set with a ______________. A. multimeter B. manometer C. spring scale D. compound gauge

Description : D.C. propulsion motor brush pressure depends on the brush grade used and in practice is set with a ______________. A. multimeter B. manometer C. spring scale D. compound gauge

Last Answer : Answer: C

Before using an all-purpose electric measuring instrument (multimeter) utilizing internal batteries to supply power for resistance measurements, you should FIRST ____________. A. remove one of the batteries B. remove all the batteries C. calibrate using a known external resistance D. select the proper resistance range

Description : Before using an all-purpose electric measuring instrument (multimeter) utilizing internal batteries to supply power for resistance measurements, you should FIRST ____________. A. remove one of the ... batteries C. calibrate using a known external resistance D. select the proper resistance range

Last Answer : Answer: D

A multimeter can be used to measure _____________. A. resistance B. voltage C. current D. all of the above

Description : A multimeter can be used to measure _____________. A. resistance B. voltage C. current D. all of the above

Last Answer : Answer: D

When using a multimeter for resistance measurements, it should be calibrated by clipping the loose ends of the leads together and _____________. A. setting the instrument pointer at 'zero' ohms B. adjusting the line voltage to calibrate the instrument C. plugging each end of one test lead into the plus and minus terminals D. using a special purpose resistance measuring instrument (a bridge)

Description : When using a multimeter for resistance measurements, it should be calibrated by clipping the loose ends of the leads together and _____________. A. setting the instrument pointer at 'zero' ohms B. ... the plus and minus terminals D. using a special purpose resistance measuring instrument (a bridge)

Last Answer : Answer: A

A multimeter may be damaged by taking a _____________. A. voltage reading while in the ammeter mode B. current reading while in the voltmeter mode C. resistance reading while in the ammeter mode D. resistance reading while in the voltmeter mode

Description : A multimeter may be damaged by taking a _____________. A. voltage reading while in the ammeter mode B. current reading while in the voltmeter mode C. resistance reading while in the ammeter mode D. resistance reading while in the voltmeter mode

Last Answer : Answer: A

You are calibrating a multimeter using internal batteries to supply power for resistance measurements. However, you are unable to adjust the pointer to 'zero' using the adjustment knob. Therefore, you should _____________. A. replace the batteries in the instrument B. measure resistance by dividing the voltmeter indication by the ammeter indication C. set the pointer using a bridge D. change scales to the R X 100 scale and adjust using the 'zero ohms' adjusting knob

Description : You are calibrating a multimeter using internal batteries to supply power for resistance measurements. However, you are unable to adjust the pointer to 'zero' using the adjustment knob. Therefore, you should ... change scales to the R X 100 scale and adjust using the 'zero ohms' adjusting knob

Last Answer : Answer: A

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'F'? EL-0047 A. 0.6 ohms B. 6 ohms C. 9.6 ohms D. .38 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'F'? EL-0047 A. 0.6 ohms B. 6 ohms C. 9.6 ohms D. .38 ohms

Last Answer : Answer: A