What meter reading is shown on each multimeter in each  part of figure 1-50?

1 Answer

Answer :

(A) 410 mA dc; (B) 3.9 mA ac; (C) -22 V dc; (D) 600 V ac; (E)  1.4 V ac; (F) 1.9 kohms

Related questions

Description : What type of frequency meter is shown and what is the value indicated for each meter in figure 1-52?

Last Answer : A) Vibrating-reed, 60Hz. (B) Moving-disk, 58 Hz.

Description : What type of meter is shown and what is the value of the quantity being measured for each meter in figure 1-51?

Last Answer : (A) Megger (megohmmeter), infinity; (B) Wattmeter, 9.5 kilowatts (9,500 watts). (C) Watt-hour meter, 2.693 megawatt-hours 2,693 kilowatt-hours) (2,693,000 watt-hours).

Description : When reading AC current with the multimeter shown in the illustration and you are unsure of the range, the range switch should be set to ___________. EL-0047 A. 10 MA/ 10 AMP with leads in the (-10 A ... leads in the (-COMMON) and (+10 A) jacks D. unable to measure AC current with this multimeter

Last Answer : Answer: D

Description : What is the quantity shown on the watt-hour meter in figure 1-46?

Last Answer : 5.945 megawatt-hours, or 5,945 kilowatt-hours, or 5,945, 000 watt-hours.

Description : what is the reading in kwh of the electric meter shown in the exam figure below? -General Knowledge

Last Answer : 0631 is the reading in kwh of the electric meter shown in the exam figure below.

Description : In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?

Last Answer : 60 millivolts.

Description : Which of the listed statements is correct when using an analog multimeter as an ohmmeter? A. The pointer should be adjusted to zero each time a new resistance range is selected. B. The ... C. Ohmmeters are not sufficiently sized to measure conductor insulation resistance. D. All of the above.

Last Answer : Answer: D

Description : If your multimeter gives a reading in ohms when testing each end of each conductor of a three-conductor cable, this indicates ______________. A. continuity of the conductor B. an infinite resistance C. the presence of a partial ground D. that the conductor is not short circuited

Last Answer : Answer: A

Description : What type of meter is shown and what is the value of the quantity being measured for each meter in figure1-49?

Last Answer : a. A dc ammeter, 90 mA dc b. A dc voltmeter, 200 V dc c. An ac voltmeter, 4.6 V ac d. An ohmmeter, 400 ohms

Description : . If the power distribution system shown in figure 2-22 uses selective tripping, what is the time delay rating for each of the circuit breakers shown?

Last Answer : CB1-long time delay; CB2, CB3-short time delay; CB4 through

Description : Which of the listed instruments can be best used to locate a grounded field coil in a synchronous motor? A. Frequency meter B. Megohmmeter C. Voltmeter D. Multimeter

Last Answer : Answer: B

Description : When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only ... being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Last Answer : Answer: D

Description : Digital version of an AVO meter is known as a) Digital Ohmmeter b) Multimeter c) Digital Multimeter d) None of these

Last Answer : c) Digital Multimeter

Description : How is an overload condition indicated by the electronic digital multimeter?

Last Answer : Simultaneous flashing of display readouts

Description : Power for the electronic digital multimeter is normally supplied by what internal power source?

Last Answer : Rechargeable batteries.

Description : What type of circuit breaker is used on a multimeter?

Last Answer : A push button or push-pull circuit breaker (small size, low power).

Description : Why would you use a hook-on voltmeter instead of a multimeter?

Last Answer : To measure current safely and easily (with no need to disconnect the wiring of the circuit).

Description : How is the mirror on a multimeter used?

Last Answer : Make sure no image of the pointer is visible in the mirror when reading the meter.

Description : What is the reason for having a mirror on the scale of a multimeter?

Last Answer : To stop parallax error

Description : Why is the dc scale on a multimeter different than the ac scale?

Last Answer : The meter movement reacts to average ac voltage and current and the effective value is desired.

Description : How is a multimeter changed from a voltage measuring device to a resistance measuring device?

Last Answer : By changing the position of the function switch

Description : Why is a multimeter preferred over separate meters?

Last Answer : It is much more convenient to have one meter with several functions than several meters each with a single function.

Description : What is a multimeter?

Last Answer : . A single measuring device capable of performing the functions of a dc voltmeter and ammeter, an ac voltmeter and ammeter, and an ohmmeter

Description : A multimeter may be damaged by taking a _____________. A. voltage reading while in the ammeter mode B. current reading while in the voltmeter mode C. resistance reading while in the ammeter mode D. resistance reading while in the voltmeter mode

Last Answer : Answer: A

Description : In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?

Last Answer : 50 millivolts.

Description : If the fuse shown on the schematic (figure 3-10) opens, what lights will operate?

Last Answer : Only the brake lights.

Description : In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal?

Last Answer : Local oscillator and coherent oscillator.

Description : How is amplification achieved in the circuit shown in figure 2-43?

Last Answer : By varying the amount of capacitance in the circuit

Description : A tape pack has gaps in the tape winding as shown in figure 2-5. What causes this condition?

Last Answer : Tape is loosely wound on reel.

Description : A tape pack is buckled and deformed as shown in figure 2- 4. What are three possible causes for this condition?

Last Answer : a. Reel has a distorted hub, b. tape wound over small particle deposited on hub, and c. tape wound on reel with tension increasing toward end of winding.

Description : A triode amplifier similar to the one shown in figure 1-19 has an Ebb -conditions, 1.5 milliamperes of current conducts through the tube. What w

Last Answer : +275 volts

Description : What effect does the internal resistance have on the rest of the circuit shown in figure 3-60?

Last Answer : Because of the 2-volt drop across the internal resistance, only 48 volts is available for the rest of the circuit.

Description : What is the total resistance of the circuit shown in figure 3- 60?

Last Answer : 25Ω

Description : What is the total resistance of the circuit shown in figure 3- 59? (Hint: Redraw the circuit to simplify and then use equivalent resistances to compute for RT.)

Last Answer : 4Ω

Description : What is the name given to the "picture" of a circuit such as the one shown in figure 3-2?

Last Answer : A schematic diagram.

Description : What happens to the path for current when S1 is open as shown in figure 3-2(A)?

Last Answer : The path for current is incomplete; or, there is no path for current with S1 open.

Description : Which connector should you use to connect the (a) power source and (b) load to the fuseholder shown in figure 2-12(A)?

Last Answer : a. Center connector b. Outside connector

Description : The reading of the ammeter as per figure shown is

Last Answer : The reading of the ammeter as per figure shown is A. `(1)/(2)A` B. `(3)/(4)A` C. `(1)/(8)A` D. `2A`

Description : A good choice of shunt resistance will place the indicating pointer near what part of the meter scale with a normal load?

Last Answer : Midscale.

Description : A design is made on a rectangular tile of dimensions 50 cm x 17 cm as shown in figure. -Maths 9th

Last Answer : According to question find the the total area of the design and the remaining area of the tiles.

Description : A design is made on a rectangular tile of dimensions 50 cm x 17 cm as shown in figure. -Maths 9th

Last Answer : According to question find the the total area of the design and the remaining area of the tiles.

Description : The value of 'B' of Indian type W.C. shown in the given figure is: (A) 45 cm (B) 50 cm (C) 30 cm (D) 25 cm

Last Answer : (A) 45 cm

Description : When using a multimeter for resistance measurements, it should be calibrated by clipping the loose ends of the leads together and _____________. A. setting the instrument pointer at 'zero' ohms B. ... the plus and minus terminals D. using a special purpose resistance measuring instrument (a bridge)

Last Answer : Answer: A

Description : Examine the three capacitors shown below. What is the capacitance of each?

Last Answer : a. 26µF or 260,00pF b. 630pF c. 9600pF

Description : In the part of circuit shown in figure, match the following two columns for `V_(AB)`

Last Answer : In the part of circuit shown in figure, match the following two columns for `V_(AB)`

Description : A kite in the shape of a square with a diagonal 32 cm and an isosceles triangle of base 8 cm and sides 6 cm each is to be made of three different shades as shown in figure. -Maths 9th

Last Answer : Each shade of paper is divided into 3 triangles i.e., I, II, III 8 cm For triangle I: ABCD is a square [Given] ∵ Diagonals of a square are equal and bisect each other. ∴ AC = BD = 32 cm Height of AABD ... are: Area of shade I = 256 cm2 Area of shade II = 256 cm2 and area of shade III = 17.92 cm2

Description : Five point charges each of charge + q are placed on five vertices of a regular of side h as shown in the figure. Then

Last Answer : Five point charges each of charge + q are placed on five vertices of a regular of side h as shown in the ... (4piepsilon_(0))q^(2)/h^(2)` along OC.

Description : A non - popular loop of conducting wire carrying a current `I` is placed as shown in the figure . Each of the straighrt sections of the loop is of the

Last Answer : A non - popular loop of conducting wire carrying a current `I` is placed as shown in the figure . Each of the ... `(1)/(sqrt(2))(hat(i)+hat(k))`

Description : Six resistance each of value `r=5 Omega` are connected between points A, B and C as shown in figure. If `R_(1), R_(2)` and `R_(3)` are the net resista

Last Answer : Six resistance each of value `r=5 Omega` are connected between points A, B and C as shown in figure. If `R_(1), R_(2) ... 1:2:3` C. `5:4:3` D. `4:3:2`

Description : Each resistor shown in the figure has a resistance of `10 Omega` and the battery has the emf 6 V. What will be the current supplied by the battery ?

Last Answer : Each resistor shown in the figure has a resistance of `10 Omega` and the battery has the emf 6 V. What will be the ... 2 A` C. `1.8 A` D. `0.3 A`