Description : If the mu of a tube is 85 and the signal at the control grid is 4 volts ac, the plate voltage will vary by what amount?
Last Answer : 340 volts.
Description : The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?
Last Answer : 42.
Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the voltage measured across R1 EL-0036 A. 11.86 volts B. .131 volts C. 12 volts D. .673 volts
Last Answer : Answer: B
Description : If the load in question 50 requires a voltage of +90 V, what should be the value of the bleeder resistor?
Last Answer : 2 kΩ
Description : How does transit time affect the relationship of the grid voltage and the plate current at high frequencies?
Last Answer : Transit time causes the grid voltage and plate current to be out of phase
Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC
Last Answer : Answer: C
Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC
Last Answer : Answer: A
Description : In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC
Description : What effect does the shielding of the screen grid by the control grid have on plate current in beam-forming tetrodes?
Last Answer : By increasing the number of electrons that reach the plate, plate current is increased.
Description : An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms
Last Answer : ANSWER: Z -- 200 OHMS
Description : Transconductance is a measure of the relationship between what two factors?
Last Answer : The changes in plate current and grid voltage.
Description : What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?
Last Answer : -5 volts.
Description : If the output of a half-wave rectifier is 50-volts peak, what is the average voltage
Last Answer : 15.9 volts.
Description : If the source voltage for the voltage divider in question 50 supplies 150 volts, what is the total current through the voltage divider?
Last Answer : 495 mA.
Description : A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?
Last Answer : 50 volts.
Description : A large negative voltage is applied to the plate of a diode, and a largewhat tube parameter has been exceeded?
Last Answer : Peak Inverse Voltage (PIV).
Description : Why does the grid have a greater effect than the plate on electron flo
Last Answer : Because it is closer to the cathode.
Description : How much must the fpa plate current vary to produce 100- percent modulation in a plate modulator?
Last Answer : Between 0 and nearly two times its unmodulated value.
Description : What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts
Description : An ammeter has a full-scale deflection current of 100mA. If the same ammeter is used to measure a full-scale current of 1.0ampere, what is the value of the shunt resistor in ohms if the voltage across the meter is 9.0 volts?
Last Answer : 10 ohms
Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 24 kohms, and R2 is 3610 ohms what is the current flowing through R1? EL-0036 A. .434 milliamps B. .005 amp C. 6.00 amps D. 2.4 milliamps
Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the total power consumed by the circuit? EL-0036 A. 3.6 watts B. 72 watts C. .0011286 watts D. .014243 watts
Last Answer : Answer: D
Description : The most practical way to control the voltage output of an AC generator is to vary the _____________. A. number of windings B. speed of the rotating field C. strength of the rotating magnetic field D. power factor of the load
Description : Automatic voltage regulators provided on switchboards function to _____________. A. regulate the AC load on the generator B. protect the switchboard from high voltage C. govern prime mover speed to control voltage D. vary the field excitation to the generators
Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?
Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.
Description : In case of Raymond pile (A) Lengths vary from 6 m to 12 m (B) Diameter of top of piles varies from 40 cm to 60 cm (C) Diameter of pile at bottom varies from 20 cm to 28 cm (D) All the above
Last Answer : Answer: Option D
Description : For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ a) Increase b) Decrease c) Remains constant d) Can’t be determined. Varies from material to material
Last Answer : a) Increase
Description : When a voltage of 95 VDC is applied to the illustrated circuit with a resistance of 10.23 kohms the current will be _______ . EL-0018 A. 9.29 milliamps B. 107.68 amps C. 10.32 amps D. 11.02 amps
Description : In the illustrated circuit, what is the resistance across R2 if the battery voltage is 32 VDC, the resistance of R1 is 1.2 kohms and the current through R2 is 18.82 milliamps? EL-0036 A. 500 ohms B. 1,200 ohms C. 10 ohms D. The answer can not be found with the information given.
Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A
Last Answer : D. 2.0 A
Description : When a wide band of frequencies is transmitted simultaneously, each frequency will vary in the amount of fading. What is this variable fading called?
Last Answer : Selective fading.
Description : If a power supply produces 20 volts with no load and 15 volts under full load, what is the percent of regulation?
Last Answer : 33.33%
Description : What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?
Last Answer : 63.7 volts.
Description : What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?
Last Answer : 63.6 volts.
Description : Using the graph in figure 3-7, what is the approximate value of current when the voltage is 12.5 volts?
Last Answer : 1.25 amperes.
Description : a. Define the term "working voltage" of a capacitor. b. What should be the working voltage of a capacitor in a circuit that is operating at 600 volts?
Last Answer : a. It is the maximum voltage the capacitor can work without risk of damage. b. 900 volts.
Description : What name is given to a resistor used to replace the normal load in a circuit?
Last Answer : Dummy load or dummy antenna.
Description : Once ionization has occurred in a thyratron, what control does the control grid have over the tube’s operation?
Last Answer : None.
Description : Why the control grid of a triode amplifier is negatively biased?
Last Answer : To prevent them from drawing grid current.
Description : When is a control-grid modulator used?
Last Answer : In cases when the use of a minimum of af modulator power is desired.
Description : If the current was increased to 4 amps, what would be the voltage drop across each resistor in the circuit described in question 17?
Last Answer : E1 = 80 volts. E2 = 240 volts. E3 = 320 volts
Description : What is the voltage dropped by each resistor of the circuit described in question 17?
Last Answer : E1 = 60 volts. E2 = 180 volts. E3 = 240 volts.
Description : A circuit is to be designed in which a capacitor must charge to 40 percent of the maximum charging voltage in 200 microseconds. The resistor to be used has a resistance of 40,000 ohms. What size capacitor must be used?
Last Answer : 0.1 microfarads 40% from the graph = 0.5
Description : What is the voltage drop across the resistor in an RC charging circuit when the charge on the capacitor is equal to the battery voltage?
Last Answer : Zero.
Description : At what instant does the greatest voltage appear across the resistor in a series RC circuit when the capacitor is charging?
Last Answer : At the instant of the initiation of the action.
Description : A triac thyristor functions as a control device and is basically ________________. A. two NPN transistors in parallel with a common base lead B. a diode in series with a temperature sensitive capacitor C. two ... -back SCR's with a common gate lead D. a triode tube with an extra heavy grid element
Description : . Which type of variable resistor should you select for controlling a large amount of current?
Last Answer : The rheostat.
Description : What is the approximate voltage produced by a nickel-cadmium battery cell? A. 1.25 volts B. 1.50 volts C. 2.20 volts D. 6.05 volts
Description : A carbon resistor has a resistance of 50 ohms, and a tolerance of 5 percent. What are the colors of bands one, two, three, and four, respectively?
Last Answer : The bands are green, black, black, and gold.
Description : Why does earths temperature vary greatly during the day while it and ocean temperature varies only slightly?
Last Answer : Need answer