The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc

The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be

• 12.1 volt

• 1.21 volt

• 0.482 volt

• 4.82 volt
by

1 Answer

Answer :

The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be 12.1 volt

by

Related questions

If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the top lead positive with repect to the lower lead B. direct current, half wave rectified with a ripple frequency of 60 hz C. direct current with the top lead negative with repect to the lower lead D. clipped to a value equal to the square root of 3 times the input voltage value

Description : If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the ... lower lead D. clipped to a value equal to the square root of 3 times the input voltage value

Last Answer : Answer: C

In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output?

Description : In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output? (A) 30 Hz (B) 60 Hz (C) 20 Hz (D) 15 Hz

Last Answer : In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output? (A) 30 Hz (B) 60 Hz (C) 20 Hz (D) 15 Hz

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Description : An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Last Answer : Solution:

One diode of a full-wave rectifier has burned out in a shorted condition. Therefore, the output will be ____________. A. zero B. a rectified half-wave C. a rectified full-wave D. equal to the AC input

Description : One diode of a full-wave rectifier has burned out in a shorted condition. Therefore, the output will be ____________. A. zero B. a rectified half-wave C. a rectified full-wave D. equal to the AC input

Last Answer : Answer: D

A full-wave rectifier has one diode burned out in an open condition, what will be the output characteristic of the device? A. Zero B. Half-wave rectified C. Full-wave rectified D. Equal to the AC input

Description : A full-wave rectifier has one diode burned out in an open condition, what will be the output characteristic of the device? A. Zero B. Half-wave rectified C. Full-wave rectified D. Equal to the AC input

Last Answer : Answer: B

Ripple factor for a half wave rectifier is ....

Description : Ripple factor for a half wave rectifier is  a. 1.65 b. 1.45 c. 1 d. 1.21 

Last Answer : Ripple factor for a half wave rectifier is 1.21

In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is

Description : In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is   (a) 233.91 V (b) 116.95V (c) 202.56 V (d) 101.28V 

Last Answer : a

On AC vessels, which of the following statements represents the most difficult problem involved in obtaining a DC potential suitable for use by computer components? A. A stepdown transformer is always required. B. Vessel vibrations affect the voltage source. C. The voltage must be rectified and made ripple free. D. Rectifiers cannot operate with voltage regulators.

Description : On AC vessels, which of the following statements represents the most difficult problem involved in obtaining a DC potential suitable for use by computer components? A. A stepdown transformer is ... voltage must be rectified and made ripple free. D. Rectifiers cannot operate with voltage regulators.

Last Answer : Answer: C

A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free.

Description : A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively   (a) 10A, 7.07A (b) 5A, 10A (c) 5A, 7.07A (d) 7.07A, 5A

Last Answer : A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively 5A, 7.07A

What is the Ripple frequency of a half-wave rectifier if the input frequency is 60 Hz?

Description : What is the Ripple frequency of a half-wave rectifier if the input frequency is 60 Hz?

Last Answer : 60 hertz.

A single phase, half-wave, controlled rectifier has 400 sin (314 t) as the input voltage and R as the load...

Description : A single phase, half-wave, controlled rectifier has 400 sin (314 t) as the input voltage and R as the load. For a firing angle of 60° for the SCR, the average output voltage is   (a) 240/π (b) 400/π (c) 300/π (d) 200/π 

Last Answer : C

The input frequency is 50 Hz. The ripple frequency in a 12 phase full wave rectifier is

Description : The input frequency is 50 Hz. The ripple frequency in a 12 phase full wave rectifier is (A) 1200 Hz (B) 600 Hz (C) 100 Hz (D) 50 Hz 

Last Answer : The input frequency is 50 Hz. The ripple frequency in a 12 phase full wave rectifier is 1200 Hz

The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Description : The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Last Answer : a) A pulsating uni-directional current

An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to

Description :  An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

Last Answer :  An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Description : The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Last Answer : Answer: A

In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary

Description : In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary winding is 30 V. Then PIV is: (1) 30 V (2) 60 V (3) 15 V (4) 10 V

Last Answer : In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary winding is 30 V. Then PIV is: 60 V

In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

Description : In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

Last Answer : In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage decreases

When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?

Description : When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?

Last Answer : Feel Free to Answer

What effect does an open diode have on the output voltage of a half wave rectifier and on a full wave rectifier?

Description : What effect does an open diode have on the output voltage of a half wave rectifier and on a full wave rectifier?

Last Answer : An open diode will result in no output from a half waverectifier, and an open diode will cut the output of a full waverectifier in half.

If the output of a half-wave rectifier is 50-volts peak, what is the average voltage

Description : If the output of a half-wave rectifier is 50-volts peak, what is the average voltage

Last Answer : 15.9 volts.

A single-phase half-controlled rectifier is driving a separately excited dc motor. The dc motor has a back emf

Description : A single-phase half-controlled rectifier is driving a separately excited dc motor. The dc motor has a back emf constant of 0.5 V/rpm. The armature current is 5 A without any ripple. The armature resistance is 2 Ohm. The ... of the motor will be  (A) 339 rpm (B) 359 rpm (C) 366 rpm (D) 386 rpm

Last Answer : 359

The correct term for the illustrated circuit is a ________. EL-0063 A. single phase half wave high power rectifier B. three phase half wave rectifier C. three phase full wave rectifier D. a single phase full wave rectifier

Description : The correct term for the illustrated circuit is a ________. EL-0063 A. single phase half wave high power rectifier B. three phase half wave rectifier C. three phase full wave rectifier D. a single phase full wave rectifier

Last Answer : Answer: C

What is the ripple frequency of a full-wave rectifier with an input frequency of 60 Hz?

Description : What is the ripple frequency of a full-wave rectifier with an input frequency of 60 Hz?

Last Answer : 120 hertz.

What is the ripple frequency of a full-wave rectifier with an input frequency of 60 Hz?

Description : What is the ripple frequency of a full-wave rectifier with an input frequency of 60 Hz?

Last Answer : 120 hertz.

Define following parameter of rectifier: (i) Ripple factor (ii) Efficiency (iii) Peak Inverse Voltage (iv) Transformer utilization factor

Description : Define following parameter of rectifier: (i) Ripple factor (ii) Efficiency (iii) Peak Inverse Voltage (iv) Transformer utilization factor

Last Answer : (i) Ripple Factor - Ripple factor (γ) may be defined as the ratio of the root mean square (rms) value of the ripple voltage to the absolute value of the DC component of the ... the same rectifier. Effective VA Rating of transformer is the average of primary and secondary VA rating of transformer.

In a full wave rectifier with input frequency of 50 Hz, the frequency of the output is:

Description : In a full wave rectifier with input frequency of 50 Hz, the frequency of the output is: (1) 50 Hz (2) 100 Hz (3) 150 Hz (4) 200 Hz

Last Answer : In a full wave rectifier with input frequency of 50 Hz, the frequency of the output is: 100 Hz

The most common source of excitation for synchronous motors is a/an ______________. A. stepup transformer B. half-wave rectifier C. DC supply D. AC supply

Description : The most common source of excitation for synchronous motors is a/an ______________. A. stepup transformer B. half-wave rectifier C. DC supply D. AC supply

Last Answer : Answer: C

In a half wave rectifier the rms value of AC component of the waves (a) Zero (b) Equal to DC value (c) More than DC value (d) Less than DC value

Description : In a half wave rectifier the rms value of AC component of the waves (a) Zero (b) Equal to DC value (c) More than DC value (d) Less than DC value

Last Answer : b) Equal to DC value

The r.m.s. value of a half-wave rectified alternating current is 10 A. Its value for full-wave rectification will be

Description : The r.m.s. value of a half-wave rectified alternating current is 10 A. Its value for full-wave rectification will be  

Last Answer : The RMS value of a half-wave rectified current is 10 Ampere. Its value for full-wave rectification would be: 14.14 Ampere

Which of the following expresses the relationship of the input and output frequencies in a full wave rectifier? A. The output frequency is the same as input frequency. B. The output frequency is one-half the input frequency. C. The output frequency is twice the input frequency. D. The output frequency is four times the input frequency.

Description : Which of the following expresses the relationship of the input and output frequencies in a full wave rectifier? A. The output frequency is the same as input frequency. B. The output frequency is ... frequency is twice the input frequency. D. The output frequency is four times the input frequency.

Last Answer : Answer: C

Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?

Description : Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?

Last Answer : Yes.

What is the output of a half-wave rectifier?

Description : What is the output of a half-wave rectifier?

Last Answer : A pulsating dc voltage.

Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?

Description : Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?

Last Answer : Yes.

What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Description : What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Last Answer : 63.7 volts.

What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Description : What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Last Answer : 63.6 volts.

In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system

Description : In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: (1) 400 Hz (2) 800 Hz (3) 1200 Hz (4) None of these

Last Answer : In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: 1200 Hz

If a half-wave rectifier is added to a half-wave voltage doubler, the resulting circuit is a voltage ___

Description : If a half-wave rectifier is added to a half-wave voltage doubler, the resulting circuit is a voltage ___

Last Answer : Trippler.

What is the equation for determining average voltage in a half-wave rectifier?

Description : What is the equation for determining average voltage in a half-wave rectifier?

Last Answer : Eavg = 0.318 × Emax

Ripple in output current of a step-down chopper feeding RLE load is maximum, when duty cycle is equal to:

Description : Ripple in output current of a step-down chopper feeding RLE load is maximum, when duty cycle is equal to:  (1) 1 (2) 0.5 (3) 0.75 (4) 0.33

Last Answer : Ripple in output current of step down Chopper feeding a RLE load is maximum, when duty cycle is equal to 0.5

A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave

Description : A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave uncontrolled ac-dc converter used for charging a battery (12 V dc) with the series current limiting resistor being 19.04 Ohm. The charging current is  (A) 2.43 A (B) 1.65 A (C) 1.22 A (D) 1.0 A

Last Answer : A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave uncontrolled ac-dc converter used for charging a battery (12 V dc) with the series current limiting resistor being 19.04 Ohm. The charging current is 1.0 A

A single phase transformer is designed to operate from 50 Hz, 1100 V supply and to have an output voltage

Description : A single phase transformer is designed to operate from 50 Hz, 1100 V supply and to have an output voltage of 240 V at no load. The core has mean area of 30 cm2 and the flux density has not to exceed 1.3T. The number of secondary turns will be (a) 1270 (b) 1017 (c) 768 (d) 277  

Last Answer : E2=e2=4.44*flux*N2*f=240 V Flux=Flux density* Area Area=30 cm2  =30*10-4 m2 Flux= 1.3*30*10-4  Wb=39*10-4 Wb E=240= 4.44*39*10-4 *N2*50      N2=277.

What is the ripple factor of the rectifier?

Description : What is the ripple factor of the rectifier?

Last Answer : A4: The ripple factor of the rectifier: - Half wave recitifer:-1.21, Center tape wave rectifier:-0.48 Bridge full wave:-0.48

Define given parameters and state their values for bridge rectifier (i) Ripple factor (ii) PIV of diode.

Description : Define given parameters and state their values for bridge rectifier (i) Ripple factor (ii) PIV of diode.

Last Answer : Ripple Factor: Ripple Factor is defined as the ratio of RMS value of the AC component of output to the DC or average value of the output. Mathematically it is expressed as, ( ... which appears across non-conducting reverse biased diode. (ii) PIV of diode for bridge rectifier-Vm

Name the circuit used in rectifier to minimize ripple. List the types of this circuit with simple circuit diagram.

Description : Name the circuit used in rectifier to minimize ripple. List the types of this circuit with simple circuit diagram.

Last Answer : Rectifier filter is an electronic circuit that removes ripple or unwanted AC signal components from the output of a Rectifier. Types - (a) Series Inductor filter (d) Shunt capacitor filter (b) L-C type filter (e) Π - type filter

Define PIV, TUF, ripple factor, efficiency of rectifier.

Description : Define PIV, TUF, ripple factor, efficiency of rectifier.

Last Answer : PIV: Peak Inverse Voltage (PIV) is defined as the maximum negative voltage which appears across non-conducting reverse biased diode. TUF : Transformer Utilization Factor (TUF) is defined as the ratio of DC output ... Efficiency of rectifier: η = DC output power/ AC input power = PLdc / Pac

Define the term 'Ripple factor' for rectifier.

Description : Define the term 'Ripple factor' for rectifier.

Last Answer : Ripple factor: The ratio of RMS value of ac component present in the waveform to the dc component in the waveform is called as ripple factor.  OR  The unwanted AC components present in output waveform of a rectifier is called as ripple factor.

The ripple factor of a bridge rectifier is

Description : The ripple factor of a bridge rectifier is  1.0.48 2.0.812 3. 1.11 4. 1.21 

Last Answer : The ripple factor of a bridge rectifier is 0.48

Capacitors are used on the output of the power supply in today's consoles to _____________. A. filter out 'ripple' B. prevent overloads C. act as a permanent load D. decrease the average value of the output voltage

Description : Capacitors are used on the output of the power supply in today's consoles to _____________. A. filter out 'ripple' B. prevent overloads C. act as a permanent load D. decrease the average value of the output voltage

Last Answer : Answer: A

If the inductance of a choke-input filter is increased, will the output ripple voltage amplitude (Er) increase or decrease?

Description : If the inductance of a choke-input filter is increased, will the output ripple voltage amplitude (Er) increase or decrease?

Last Answer : Decrease.

Rectification efficiency of a full wave rectifier without filter is nearly equals to:

Description : Rectification efficiency of a full wave rectifier without filter is nearly equals to:  (1) 51% (2) 61% (3) 71% (4) 81%

Last Answer : Rectification efficiency of a fullwave rectifier without filter is nearly equals to: 81%