What controls transmitter pulse width?

1 Answer

Answer :

The modulator.

Related questions

Description : What controls transmitter pulse width?

Last Answer : The modulator.

Description : What component in a blocking oscillator controls pulse width?

Last Answer : Transformer.

Description : The spectrum of a radar transmitter describes what characteristic of the output pulse?

Last Answer : Frequency distribution

Description : When a transmitter uses a high-power oscillator to produce the output pulse, what switches the oscillator on and off?

Last Answer : High-voltage pulse from the modulator.

Description : What width is the pulse radiated by fire-control tracking radar?

Last Answer : Very narrow.

Description : What term is used to describe the product of pulse width and pulse-repetition frequency?

Last Answer : Duty cycle.

Description : Type of modulation used in TV broadcast visual transmitter. A. Pulse modulation B. DSBFC C. Vestigial sideband D. SSBFC

Last Answer : C. Vestigial sideband

Description : What is pulse-width modulation (PWM) in Arduino?

Last Answer : Pulse-width modulation (PWM) in Arduino is a technique used to control the brightness of an LED or the speed of a motor by varying the duty cycle of a digital signal.

Description : What is a pulse-width modulation (PWM) signal in Arduino?

Last Answer : A PWM signal in Arduino is a digital signal that varies the width of the pulse to simulate an analog signal.

Description : What is Pulse Width Modulation?

Last Answer : Ans-Pulse width modulation is a modulation technique in which the width of the pulse is varied in accordance with the message signal. Pulse width Modulation is abbreviated as PWM. PWM can be used ... the pulse train and recover an average analog waveform. PWM is used in sound synthesis circuits.

Description : It indicates what signal frequencies can be propagated through a given distance of fiber cable. ∙ A. Bandwidth Distance Product ∙ B. Pulse width dispersion ∙ C. Rise time ∙ D. Cutoff frequency

Last Answer : A. Bandwidth Distance Product

Description : The width of the vertical sync pulse in the Philippine TV system is

Last Answer : 3H

Description : The width of the vertical sync pulse in the Philippine TV system is

Last Answer : 3H

Description : Pulse width modulation may be generated:

Last Answer : with a monostable multivibrator

Description : A pulse modulation technique as the width of a constant amplitude pulse is varied proportional to the amplitude of the analog signal at the time the signal is sampled.

Last Answer : PWM, PLM, PDM

Description : For the most Static RAM the write pulse width should be at least a) 10ns b) 60ns c) 300ns d) 1μs

Last Answer : b) 60ns

Description : An eight stage ripple counter uses a flip-flop with propagation delay of 75 nanoseconds. The pulse width of the strobe is 50ns. The frequency of the input signal which can be used for proper operation of the counter is approximately (A) 1 MHz. (B) 500 MHz. (C) 2 MHz. (D) 4 MHz.

Last Answer : Maximum time taken for all flip-flops to stabilize is 75ns x 8 + 50 = 650ns. Frequency of operation must be less than 1/650ns = 1.5 MHz.

Description : In single pulse modulation of PWM inverters, third harmonic can be eliminated if pulse width is equal to   (a) 30o (b) 60o (c) 120o (d) 150o

Last Answer : In single pulse modulation of PWM inverters, third harmonic can be eliminated if pulse width is equal to 120o

Description : A 3 -stage ripple counter has Flip Flop with propagation delay of 25 nsec and pulse width of strobe input 10 nsec. Then the maximum operating frequency at which counter operates reliably is

Last Answer : A 3 -stage ripple counter has Flip Flop with propagation delay of 25 nsec and pulse width of strobe input 10 nsec. Then the maximum operating frequency at which counter operates reliably is 12.67 MHz

Description : A pulse waveform has a high time of 8 ms and a pulse width of 32 ms. The duty - cycle is equal to: A. 25% B. 50% C. 1% D. 100%

Last Answer : A pulse waveform has a high time of 8 ms and a pulse width of 32 ms. The duty - cycle is equal to:  25%

Last Answer : PWM means the width of pulse signal can be varied by varying ton & tOFF.

Description : What precaution should you take when substituting a synchro tester in a circuit for a transmitter?

Last Answer : Use only one receiver so as not to overload the tester.

Description : What is the most likely problem if the transmitter shaft reads 0º when the receiver shaft indicates 180º?

Last Answer : The rotor leads on either the transmitter or the receiver are reversed.

Description : What is the relationship between the transmitter and receiver stator voltages when their rotors are in correspondence?

Last Answer : The voltages are equal and oppose each other.

Description : What is the physical difference between a synchro transmitter and a synchro receiver?

Last Answer : A synchro receiver uses some form of damping to retard excessive oscillations or spinning.

Description : Describe the zero-position of a synchro transmitter.

Last Answer : The transmitter is in its zero-position when the rotor is aligned with the S2 stator winding.

Description : What unit of measurement refers to the torque of a synchro transmitter

Last Answer : Ounce-inches.

Description : What are some disadvantages of operating a transmitter at or near the muf?

Last Answer : Frequent signal fading and dropouts.

Description : What are three ways of controlling the amount of transmitter-generated emi?

Last Answer : (a) filtering and shielding of the transmitter (b) limiting bandwidth (c) cutting the antenna to the

Description : Transmitter power readings are most often referenced to what power level?

Last Answer : 1 milliwatt.

Description : Where should the transmitter spectrum be located with respect to the receiver response curve?

Last Answer : In the center.

Description : Immediately after the transmitter fires, stc reduces the receiver gain to what level?

Last Answer : Zero.

Description : What type of klystron is used as the final stage of a power- amplifier transmitter?

Last Answer : Multicavity klystron.

Description : What transmitter component allows the radiation of a large number of discrete frequencies over a wide band?

Last Answer : . Frequency synthesizer.

Description : What type of klystron is used as the final stage of a power- amplifier transmitter?

Last Answer : Multicavity klystron.

Description : In an externally synchronized radar, what determines the prr of the transmitter?

Last Answer : The master oscillator.

Description : What transmission method uses a stable cw reference oscillator, which is locked in phase with the transmitter frequency?

Last Answer : Pulse-Doppler.

Description : What factor determines the difference between the transmitted frequency and the received frequency in an fm transmitter?

Last Answer : Travel time.

Description : The beat frequency in a swept-frequency transmitter provides what contact information?

Last Answer : Range.

Description : What type of radar transmitter power is measured over a period of time?

Last Answer : Average power.

Description : What vswr is a perfect match between a transmitter and its load?

Last Answer : 1 to 1.

Description : What is the result of an impedance mismatch between a receiver or transmitter and its transmission line or antenna?

Last Answer : High vswr, which equates to poor reception or a loss of power output.

Description : All the power sent down a transmission line from a transmitter can be transferred to an antenna under what optimum conditions?

Last Answer : When the characteristic impedance of the transmission line and the load impedance are equal.

Description : What term is used for the end of the transmission line that is connected to a transmitter?

Last Answer : Input end, generator end, transmitter end, sending end, and source.

Description : What connecting link is used to transfer energy from a radio transmitter to its antenna located on

Last Answer : Transmission line.

Description : List five common fiber optic transmitter packages.

Last Answer : TO can, DIP, butterfly lead microcircuits, circuit cards, and stand-alone optical fiber converters.

Description : Which part of a fiber optic transmitter converts the processed electrical signal to an optical signal?

Last Answer : The optical source.

Description : What are the three parts of a fiber optic transmitter?

Last Answer : Interface circuit, source drive circuit, and an optical source.

Description : What is the range of earth terminal transmitter output power?

Last Answer : Up to 20 kilowatts.

Description : In an fm transmitter, when does an oscillator generate only a steady frequency?

Last Answer : When no modulation is present.