Y –axis in a CRO normally represents

Y –axis in a CRO normally represents
by

2 Answers

Answer :

Y –axis in a CRO normally represents Voltage

by

Answer :

Volt 
by

Related questions

sketch time period measurement by CRO.

Description : sketch time period measurement by CRO.

Last Answer : Horizontal sweep is turned ON and the display appealing on the screen is adjusted by varying different control knobs provided on the front panel of CRO, till the signal is suitably displayed ... Where m=Number of division in one complete cycle n=Setting of time base =Time/Division

application of CRO.

Description : application of CRO.

Last Answer : Applications of CRO: 1) Voltage measurement. 2) Current measurement. 3) Measurement of phase difference. 4) Measurement of phase. 5) Measurement of frequency. 6) Measurement of inductance. ... in various circuits. 17) For checking transistor. 18) It can measure short time interval.

The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the

Description : The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the potential difference between the Y-plates is doubled, and simultaneously the pre-accelerating anode voltage is reduced to half of ... on the screen would become (A) 64 mm (B) 32 mm (C) 8 mm (D) 1 mm

Last Answer : The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the potential difference between the Y-plates is doubled, and simultaneously the pre-accelerating ... of its previous value. Then, the vertical deflection of the beam on the screen would become 32 mm

The Lissajous pattern observed on screen of CRO is a straight line inclined at 45° to x axis. If X–plate input is

Description : The Lissajous pattern observed on screen of CRO is a straight line inclined at 45° to x axis. If X–plate input is 2 sin ωt, the Y–plate input is (1) 2 sin ωt (2) 2 sin (ωt + 45°) (3) 2 sin (ωt – 45°) (4) 22 sin ωt + 45°) 

Last Answer : The Lissajous pattern observed on screen of CRO is a straight line inclined at 45° to x axis. If X–plate input is 2 sin ωt, the Y–plate input is 2 sin ωt 

The Lissajous pattern on the screen of a CRO is an ellipse with major axis in quadrant 2 and quadrant 4.

Description : The Lissajous pattern on the screen of a CRO is an ellipse with major axis in quadrant 2 and quadrant 4. Then the phase difference between two signals Can be :  (A) 270° (B) 210° (C) 180° (D) 300°

Last Answer : The Lissajous pattern on the screen of a CRO is an ellipse with major axis in quadrant 2 and quadrant 4. Then the phase difference between two signals Can be : 210°

In Mohr’s circle of strain, y-axis represents a. Shear strain b. Half of shear strain c. Normal strain d. Half of normal strain

Description : In Mohr’s circle of strain, y-axis represents a. Shear strain b. Half of shear strain c. Normal strain d. Half of normal strain

Last Answer : b. Half of shear strain

The graphical method of Mohr's circle represents shear stress (τ) on ______ a. X-axis b. Y-axis c. Z-axis d. None of the above

Description : The graphical method of Mohr's circle represents shear stress (τ) on ______ a. X-axis b. Y-axis c. Z-axis d. None of the above

Last Answer : b. Y-axis

. Which attribute of text tag of SVG represents the shift along with y-axis?

Description : . Which attribute of text tag of SVG represents the shift along with y-axis?

Last Answer : 'dy' attribute of text tag of SVG represents the shift along with y-axis.

Which attribute of text tag of SVG represents the y axis cordinates of glyphs?

Description : Which attribute of text tag of SVG represents the y axis cordinates of glyphs?

Last Answer : 'y' attribute of text tag of SVG represents the y axis cordinates of glyphs.

Two sinusoidal signals having the same amplitude and frequency are applied to the X and Y inputs of a CRO.

Description : Two sinusoidal signals having the same amplitude and frequency are applied to the X and Y inputs of a CRO. The observed Lissajous figure is straight line. The phase shift between the two signals would be (1) Zero (2) 90 degrees (3) Either zero or 180 degrees (4) Either 90 degrees or 270 degrees  

Last Answer : Two sinusoidal signals having the same amplitude and frequency are applied to the X and Y inputs of a CRO. The observed Lissajous figure is straight line. The phase shift between the two signals would be (1) Zero (2) 90 degrees (3) Either zero or 180 degrees (4) Either 90 degrees or 270 degrees  

The two inputs of a CRO are fed with two stationary periodic signals. In the X-Y mode, the screen shows a

Description : The two inputs of a CRO are fed with two stationary periodic signals. In the X-Y mode, the screen shows a figure Which changes from ellipse to circle and back to ellipse with its major ... frequencies very close but not equal D) There is a constant but small phase difference between the signals

Last Answer : The two inputs of a CRO are fed with two stationary periodic signals. In the X-Y mode, the screen shows a figure Which changes from ellipse to circle and back to ellipse with ... following inference can be made from this The signals are sinusoidal with their frequencies very close but not equal 

As shown in the illustration, which of the symbols represents a normally closed electrical contact? EL-0005 A. A B. B C. C D. D

Description : As shown in the illustration, which of the symbols represents a normally closed electrical contact? EL-0005 A. A B. B C. C D. D

Last Answer : Answer: A

In a DataFrame, Axis= 1 represents the elements. -Technology

Description : In a DataFrame, Axis= 1 represents the elements. -Technology

Last Answer : In a DataFrame, Axis= 1 represents thecolumn elements.

If a graph represents the decay of strontium 90 in an igneous rockwhat event occurred at 0 years on the horizontal axis?

Description : If a graph represents the decay of strontium 90 in an igneous rockwhat event occurred at 0 years on the horizontal axis?

Last Answer : What is the answer ?

Which set of ordered pairs represents a vertical reflection (over the x-axis) A. (5, –1) to (–5, –1) B. (–2, –3) to (–2, 3) C. (–1, –5) to (1, 5) D. (3, –2) to (–3, –2)?

Description : Which set of ordered pairs represents a vertical reflection (over the x-axis) A. (5, –1) to (–5, –1) B. (–2, –3) to (–2, 3) C. (–1, –5) to (1, 5) D. (3, –2) to (–3, –2)?

Last Answer : help me plz

Equator represents – (1) line joining North and South poles (2) imaginary line passing round the Earth midway between North & South poles (3) a belt (ring) around the planet Saturn (4) axis of rotation of Earth

Description : Equator represents – (1) line joining North and South poles (2) imaginary line passing round the Earth midway between North & South poles (3) a belt (ring) around the planet Saturn (4) axis of rotation of Earth

Last Answer : (2) imaginary line passing round the Earth midway between North & South poles Explanation: An equator is the intersection of a sphere's surface with the plane perpendicular to the sphere ... astronomical bodies have equators similarly defined. The length of the Equator is roughly 40,075 kilometres.

Which attribute of text tag of SVG represents the shift along with x-axis?

Description : Which attribute of text tag of SVG represents the shift along with x-axis?

Last Answer : 'dx' attribute of text tag of SVG represents the shift along with x-axis.

Which attribute of text tag of SVG represents the x axis cordinates of glyphs?

Description : Which attribute of text tag of SVG represents the x axis cordinates of glyphs?

Last Answer : 'x' attribute of text tag of SVG represents the x axis cordinates of glyphs.

Equator represents (1) line joining North and South poles (2) imaginary line passing round the Earth midway between North & South poles (3) a belt (ring) around the planet Saturn (4) axis of rotation of Earth

Description : Equator represents (1) line joining North and South poles (2) imaginary line passing round the Earth midway between North & South poles (3) a belt (ring) around the planet Saturn (4) axis of rotation of Earth

Last Answer : imaginary line passing round the Earth midway between North & South poles

need of calibration and explain the procedure to calibrate the instrument.

Description : need of calibration and explain the procedure to calibrate the instrument.

Last Answer : Need of calibration: Every measuring device degrades over time due to normal wear and tear. These changes can be caused by various reasons such as electric or mechanical shock or a hazardous manufacturing ... different magnitude are used to calculate the resistance based on ohm's law.

Compare Dual slope DVM and SAR type DVM.

Description : Compare Dual slope DVM and SAR type DVM.

Last Answer : Sr no Dual slope DVM SAR type DVM 1 It is highly accurate It is moderately accurate 2 Cost is high It is inexpensive 3 Two comparator is used One comparator is used ... resolution Good resolution 5 Slow speed High speed 6 Less Error More error

block diagram of logic analyzer.

Description : block diagram of logic analyzer.

Last Answer : A logic analyzer can be triggered on a complicated sequence of digital events, then capture a large amount of digital data from the system under test (SUT).When logic analysers first came ... Once the data are captured, they can be displayed several ways, from the simple) to the complex 

operation of DSO with block diagram.

Description : operation of DSO with block diagram.

Last Answer : The input is amplified and attenuated with input amplifiers. The output of the input signal amplifiers feeds an analog to digital converter (ADC). There are numbers of ADC available. But the selection of ADC ... view the display on the CRT, the data from memory is reconstructed in analog form.

operation of ramp type DVM.

Description : operation of ramp type DVM.

Last Answer : This is given to an input comparator which will compare two signals and generates the output. One input to the input comparator is from the input and another input is from the ramp. This input voltage and ... ground and output is given. This output will stop the flow of purchase from clock

operation of half wave rectifier type AC Voltmeter.

Description : operation of half wave rectifier type AC Voltmeter.

Last Answer :  Half-wave Rectifier Voltmeter The d'Arsonval meter movement only responds to the average or dc value of the current through the moving coil. In order to measure alternating ... ) input voltage signal alternating signal needs to be rectified first by using diode rectifier to produce 

operation of whetstone bridge.

Description :  operation of whetstone bridge. 

Last Answer : A Wheatstone bridge is widely used to measure the electrical resistance. This circuit is built with two known resistors, one unknown resistor and one variable resistor connected in the form of bridge. ... using a Wheatstone Bridge the unknown electrical resistance value can easily measure.

role of the series resistance connected in PMMC movement.

Description : role of the series resistance connected in PMMC movement.

Last Answer : A PMMC Instrument can be used as voltmeter by just connecting a series resistance with the moving coil. This series resistance is called Voltmeter Multiplier. This combination of moving coil and ... current whose voltage is to be measured. Ideally the resistance of voltmeter should be infinite

different types of errors occurs in measurement.

Description : different types of errors occurs in measurement.

Last Answer : Generally errors are classified into three types: systematic errors, random errors and blunders. 1) Gross Errors 2) Random Errors 3) Systematic Errors Instrumental Errors Environmental ... to wrong observations or reading in the instruments particularly in case of energy meter reading. 

tern null as it applies to bridge measurement.

Description : tern null as it applies to bridge measurement.

Last Answer : Null measurements balance voltages so that there is no current flowing through the measuring device and, therefore, no alteration of the circuit being measured. Null measurements are generally more ... the use of standard voltmeters and ammeters, and they still have limits to their precision.

How many non-overlapping channels are available in IEEE 802.11b

Description : How many non-overlapping channels are available in IEEE 802.11b

Last Answer : 3 non-overlapping channels are available in IEEE 802.11b

Number of comparators required for an 8 bit flash ADC is:

Description : Number of comparators required for an 8 bit flash ADC is: (1) 8 (2) 16 (3) 255 (4) 256

Last Answer : Number of comparators required for an 8 bit flash ADC is: 255

In D/A converter, the resolution required is 50mv and the total maximum input is 10v. The number of

Description : In D/A converter, the resolution required is 50mv and the total maximum input is 10v. The number of bits required is   (A) 7 (B) 8 (C) 9 (D) 200

Last Answer : In D/A converter, the resolution required is 50mv and the total maximum input is 10v. The number of  bits required is 8 

Choose the correct statement (a) Digital multimeters are built using current measuring elements, while analog

Description : Choose the correct statement  (a) Digital multimeters are built using current measuring elements, while analog multimeters are built using voltage measuring units (b) Digital multimeters are built ... measuring units (d) Both digital and analog multimeters are built using current measuring units

Last Answer : Choose the correct statement  (a) Digital multimeters are built using current measuring elements, while analog multimeters are built using voltage measuring units (b) Digital multimeters are built ... measuring units (d) Both digital and analog multimeters are built using current measuring units

An analog voltmeter has a sensitivity of 10kΩ/volt. The galvanometer used in constructing the instrument

Description : An analog voltmeter has a sensitivity of 10kΩ/volt. The galvanometer used in constructing the instrument will produce a full scale deflection when the current passed through it is  (a) 10 mA (b) 20 mA (c) 50 mA (d) 100 μA

Last Answer : An analog voltmeter has a sensitivity of 10kΩ/volt. The galvanometer used in constructing the instrument will produce a full scale deflection when the current passed through it is 100 μA

An optical fiber cable laid underground has developed a discontinuity at a distance d from the source end.

Description : An optical fiber cable laid underground has developed a discontinuity at a distance d from the source end. The fault can be located using the instrument  (a) Optical spectrum Analyzer (OSA) (b) Optical Time Domain Reflectometer (OTDR) (c) Optical Power Meter (OPM) (d) Laser Diffractometer (LD)

Last Answer : An optical fiber cable laid underground has developed a discontinuity at a distance d from the source end. The fault can be located using the instrument Optical Time Domain Reflectometer (OTDR) 

Two sinusoidal signals of the same frequency are displayed on a dual-trace oscilloscope. One complete cycle

Description : Two sinusoidal signals of the same frequency are displayed on a dual-trace oscilloscope. One complete cycle of each signal covers 6 cm of the horizontal scale and the starting point of the horizontal scale and the starting ... between the two signals in degrees is  (a) 30 (b) 45 (c) 60 (d) 90

Last Answer : Two sinusoidal signals of the same frequency are displayed on a dual-trace oscilloscope. One complete cycle of each signal covers 6 cm of the horizontal scale and the starting point of the horizontal ... signals are separated by 0.5 cm. The phase difference between the two signals in degrees is 30

Transient signals can be observed using

Description : Transient signals can be observed using  (a) storage oscilloscope (b) sampling oscilloscope (c) wave analyzer (d) spectrum analyzer

Last Answer : Transient signals can be observed using storage oscilloscope

The trace on an oscilloscope continually moves to the right of the screen when

Description : The trace on an oscilloscope continually moves to the right of the screen when  (a) the sweep is triggered. (b) the sweep period is larger than the signal period. (c) the sweep period is smaller than the signal period. (d) there is no weep.

Last Answer : The trace on an oscilloscope continually moves to the right of the screen when the sweep period is smaller than the signal period. 

In a dual trace oscilloscope, the display appears segmented when

Description : In a dual trace oscilloscope, the display appears segmented when  (a) low frequency signals are observed in Alternate mode (b) low frequency signals are observed in Chop mode (c) high frequency signals are observed in Alternate mode (d) high frequency signals are observed in Chop mode

Last Answer : In a dual trace oscilloscope, the display appears segmented when high frequency signals are observed in Chop mode

To distinguish between signals having very close values, we need an instrument with

Description : To distinguish between signals having very close values, we need an instrument with  (a) high accuracy (b) high resolution (c) high sensitivity (d) high linearity

Last Answer : To distinguish between signals having very close values, we need an instrument with high resolution

In a weighted-resistor digital-to-analog converter with 8-bit input, if the resistance corresponding to the MSB

Description : In a weighted-resistor digital-to-analog converter with 8-bit input, if the resistance corresponding to the MSB is 2K, what will be the resistance corresponding to the LSB?  (a) 250 Ω (d) 512 KΩ (c) 256 KΩ (d) 25.5 Ω

Last Answer : In a weighted-resistor digital-to-analog converter with 8-bit input, if the resistance corresponding to the MSB is 2K, what will be the resistance corresponding to the LSB?  (a) 250 Ω (d) 512 KΩ (c) 256 KΩ (d) 25.5 Ω

ESD stands for

Description : ESD stands for

Last Answer : ESD stands for Electro static Discharge

In a particular circuit connection, AWG 18 wire is selected over AWG 22. The reason is that it is having

Description : In a particular circuit connection, AWG 18 wire is selected over AWG 22. The reason is that it is having

Last Answer : In a particular circuit connection, AWG 18 wire is selected over AWG 22. The reason is that it is having Higher current carrying capacity

Very small displacements are effectively measured using

Description : Very small displacements are effectively measured using

Last Answer : Very small displacements are effectively measured using LVDT

What are the types of error?

Description : What are the types of error?

Last Answer : Human error or gross error, systematic error, applicational error and random error are the types of error.

What are the factors influencing measurement errors?

Description : What are the factors influencing measurement errors?

Last Answer : The factor influencing measurement errors are accuracy, precision, range and bandwidth, sensitivity, resolution and uncertainty.

What are the SI derived units?

Description : What are the SI derived units?

Last Answer : Electrical capacitance, electrical resistance, electrical inductance, force, energy, power, magnetic flux, electric charge, and electric potential difference and EMF. These are the nine SI derived units.

What are the seven base units?

Description : What are the seven base units?

Last Answer : Length, mass, time, electric current, temperature, luminous intensity and amount of substance are the seven base units.

What is logic analyser?

Description : What is logic analyser?

Last Answer : Logic analyser is the extension of Oscilloscope. Logic analyser is used for troubleshooting digital circuits. Logic analyser can store digital data and it have 8 to 64 channels. Logic analyser are used for Hardware verification, fault analysis and automated testing.