x

what are the importance of reactive power?

131 views

1 Answer

Answer :

Importance of Reactive Power

image


 

•Voltage level control is important In power system. Varying reactive power will vary voltage level.

•Reactive power is directly proportional to voltage level means if reactive power is more voltage level is more and if the reactive power is less voltage level is less.

•Reactive power is very important to avoid blackouts. Power is equal to voltage into current (P=VI). So if the voltage level is low current level is high this will cause transmission lines to go offline.

•Reactive power is required with active power to do useful work.

•Reactive power is useful in transmitting or boosting the active power in transmission lines with less losses.

•Inductive load like induction motor requires reactive power for useful work.

•Reactive power is required to generate magnetic flux.

Like 0 like

Please log in or register to answer this question.

Related Questions


Explain the term reactive power. Why it is sometimes essential to measure reactive power?
Last Answer : Reactive power: The reactive power (Q) is defined as the product of voltage(V), current (I) and sine of angle between voltage(V) and current( I) Therefore Reactive power Q = V I ... power so that corrective measures can be taken accordingly to maintain systems power factor near to the unity.

Show More

82 views 1 answer



List any two methods of reactive power measurement in 3 phase circuit.
Last Answer : Methods of reactive power measurement in 3 phase circuit: (i) Two single phase wattmeter method (ii) One single phase wattmeter method

Show More

175 views 1 answer



The reactive power transfer over a line mainly depends on
Last Answer : The reactive power transfer over a line mainly depends on lVsl- lVRl

Show More

412 views 1 answer



What is the formula for reactive power?
Last Answer : The formula for reactive power is, Reactive power = VI sin (phi) The unit of reactive power is VAR ( Volt ampere reactive). The reactive power is denoted by 'Q'. The formula for real power is, Real power = VI cos (phi) The unit of real power is watts. The real power is denoted by 'P'.

Show More

226 views 2 answers



why reactive ohm cannot converted electrical energy into heat?
Last Answer : Because it describes the resistance of element that store energy rather than dissipate energy as heat

Show More

91 views 2 answers



Use Voltmeter, ammeter, wattmeter to determine active, reactive and apparent power consumed in given R-L series circuit, draw phasor diagram.
Last Answer : Practical Significance In the industry environment Electrical Engineering diploma graduate are expected to measure basic parameters like voltage, frequency, time period etc. for R-L series circuits. Therefore ... /varying L. 7. Draw the phasor diagram for each of reading for verification.

Show More

520 views 1 answer



Precise control of reactive current flow entering the transmission and distribution systems can be minimized by using (A) synchronous condenser (B) static VAR capacitor (C) capacitor bank (D) thyristor switched reactor in parallel with capacitor
Last Answer : Precise control of reactive current flow entering the transmission and distribution systems can be minimized by using (A) synchronous condenser (B) static VAR capacitor (C) capacitor bank (D) thyristor switched reactor in parallel with capacitor

Show More

138 views 1 answer



The apparent power drawn by an A.C. circuit is 10 kVA and active power is 8 kW. The reactive power in the circuit is?
Last Answer : The apparent power drawn by an A.C. circuit is 10 kVA and active power is 8 kW. The reactive power in the circuit is 6 kVAR.

Show More

748 views 1 answer



reactive power is greater in load side compare to generator what will happen?
Last Answer : VI*sin()

Show More

163 views 2 answers



State the importance of electrical power in day to day life. 
Last Answer : Importance of electrical power in day to day life: 1. Electrical energy is the basic necessity for domestic (residency), commercial, industrial, agriculture, consumers , transport (Electric ... agriculture products. iv) Running motors, furnaces of various kinds in industry, running locomotives 

Show More

99 views 1 answer



Explain the importance of solar power in the energy deficient India.
Last Answer : Mainly electricity generated in India is from -  Hydro power plant  Thermal power plant  Nuclear power plant  BUT,  To construct new Hydro power plant following are problem :- 1. There is ... start) 10. It saves the fossil fuel (coal, diesel, oil etc.) which are limited available.

Show More

83 views 1 answer



Briefly explain how the power factor of an inductive circuit can be improved.
Last Answer : As we know that power factor should be corrected to ensure that the current supplied is cost friendly. Meaning the power factor should be around one but not greater than one(0.8-0.9) in a ... an inductive circuit due to the inductive reactance which oppose the change of current in the ac circuit. 

Show More

189 views 1 answer



What is the value of capacitance required to improve power factor from 0.7 to 0.9. Given that: Real power = 50 W Vrms of the source = 120 Frequency = 50 Hz   #powerfactor

Show More

197 views 0 answers



Why engine power is measured in horsepower (HP) ?
Last Answer : James Watt compared engine output with that of work done by a horse. WD by horse = 746W.

Show More

199 views 2 answers



Why is AC better for long distance power transmission than DC ?
Last Answer : ac is more economical to transmit for long distances . wires can be made smaller by step up transformer .. since major cost are wires to transmit .. then at the end of distance step down transformer is used for commercial use.

Show More

211 views 4 answers



Why don't we burry power lines underground ?
Last Answer : Because conductor used for power transmission are not insulated and if we do so it create phase to ground fault causing interruptions to supply.

Show More

107 views 5 answers



Why capacitors are used to improve power factor?
Last Answer :  Capacitors generate reactive power instead of that drawn from source which is required by inductive loads.so it reduce the reactive current which is drawn from source to be drawn from capacitor.This control in Electric bills cost.

Show More

185 views 3 answers



Draw the block diagram of satellite sub-system and explain power subsystem.
Last Answer : POWER SUBSYSTEM- This system provides the necessary DC power to the satellite. All communication satellites derive their electrical power from solar cells. There is also a battery backup facility used during ... . to d.c. converter is used to raise the level of low voltages to high voltage.

Show More

3.1k views 1 answer



Compare the Nuclear power station with Hydro power station. 
Last Answer : SR. No.  Points Nuclear Power plant  Hydro Power station  1 Site/ Location Where there is ample supply of water is available, away from thickly populated areas to avoid radioactive ... Field Application As base load  Used as base load during as well as peak load 

Show More

76 views 1 answer



What are the basic requirements of locating wind power plant ?
Last Answer : The basic requirements of locating wind power plant:  1) The site should be selected where winds are strong i.e. where pressure of wind is high and there is continuity. 2) Wind pressure ... the turbine which can affect the system's overall performance. 10)Possibility to connect to power grid. 

Show More

137 views 1 answer



Classify condensers used in thermal power station. Explain each type in brief. 
Last Answer : Types of condenser: Classification: 1. Jet Condenser (Mixing Type) 2. Surface condenser (non Mixing type)  Explanation:-   1. Jet Condenser (Mixing Type) In Jet condenser the steam ... there in no direct contact between the steam and cooling water. This condensate is reused in boiler. 

Show More

144 views 1 answer



State elements of diesel electric power plant with their functions. 
Last Answer : Elements of Diesel Power Plant with their function):   1) Diesel Engine: - This is the main component of the P.P. which develops mechanical power. 2) Engine air intake system: - Air ... fuel as per requirement. 10) Alternator: - Its function is to convert mechanical power into electrical power.

Show More

100 views 1 answer



Explain the working of Hydro power station with schematic layout. 
Last Answer : Working of Hydro- Electric Power Plant: Water stored at high level by constructing dam across river. This stored water has potential energy. This stored water is passed to run the water ... energy and Alternator is coupled to water turbine which converts mechanical energy into electrical energy. 

Show More

105 views 1 answer



"Efficiency of thermal power station is low". — Justify. 
Last Answer : Justification: Efficiency of thermal power station is low":- Overall efficiency of T.P.P depends upon efficiency of boiler, turbine and alternator. The heat produced due to combustion of coal ... losses in thermal power plant is 71%, So efficiency of thermal power plant is less about 29% 

Show More

106 views 1 answer



State the different methods of Power Generation adopted in India. 
Last Answer : 1. Hydro energy or hydro Electric power plant  2. Nuclear energy or nuclear Power Plant  3. Fossil fuels: i) Thermal energy (by combustion of coal) or Thermal Power Plant ii) Natural gas ... from any organic waste materials. It contains mixture of methane(50-65 % in volume) and carbon dioxide

Show More

74 views 1 answer



Applications of Diesel power station
Last Answer : Applications of Diesel Power Station:  1. It can be used as a standby (emergency) power plant to maintain continuity of supply. (Incase failure of main supply like hospital, Telephone exchange Radio ... 10. Diesel plants are widely used for generating power ranging from 100 to 5,000 H.P. 

Show More

67 views 1 answer



State two advantages of interconnection of power stations. 
Last Answer : 1) Due to interconnection it is possible of wheeling of electricity instantly.  2) The reliability and continuity of the supply is improved with interconnected grid system. With fault ... interconnection, there is optimum utilization of available natural recourses in the country is possible. 

Show More

68 views 1 answer



List out main components of Diesel power station. 
Last Answer : Main components of Diesel power station: 1) Diesel Engine 2) Engine Air intake system 3) Engine Fuel System 4) Engine Exhaust system 5) Engine cooling system 6) Engine Lubricating system 7) Engine Starting system 8) Diesel Engine Generator (Alternator) 

Show More

106 views 1 answer



State advantages of Pulverized coal w.r.t. thermal power plant. 
Last Answer : Advantages of Pulverized coal w.r.t. thermal power plant.  1. Due to pulvarization amount of fuel required to produce same amount of heat reduces. 2. Time required for combution reduces ... of air and thorough mixing of air and fuel, very high-combustion temperatures can be attained.

Show More

100 views 1 answer



State the function of super heater of a thermal power plant. 
Last Answer : Function of Super heater: -  Its function is to increase the temperature of steam by absorbing heat from exhausted hot flue gases.

Show More

87 views 1 answer



Is the power line voltage available in our homes a dc or an ac voltage?
Last Answer : The power line voltage available in our homes is AC. Mobile dwellings are the most commonly DC-supplied homes and even then they tend to include AC supply for heavier loads.

Show More

5.2k views 1 answer



Electric power formula
Last Answer : Electric power formula

Show More

65 views 1 answer



Maximum Power Transfer Theorem 1
Last Answer : Maximum Power Transfer Theorem 1

Show More

94 views 1 answer



Problems on electrical power and energy
Last Answer : Problem on electrical power and energy 1 : https://youtu.be/ZvWHuMdmv9g Problem on electrical power and energy 2 : https://youtu.be/19IZMc6U2vs Problem on electrical power and energy 3 : https ... : https://youtu.be/iYqGIwA919A Problem on electrical power and energy : https://youtu.be/iWnWQz_mzHk

Show More

2.6k views 1 answer



Problem on electrical power and energy 2
Last Answer : Problem on electrical power and energy 2

Show More

135 views 1 answer



Problem on electrical power and energy 1
Last Answer : Problem on electrical power and energy 1

Show More

75 views 1 answer



Problem on electrical power and energy 7
Last Answer : Problem on electrical power and energy 7

Show More

55 views 1 answer



Problem on electrical power and energy 6
Last Answer : Problem on electrical power and energy 6

Show More

66 views 1 answer



Problem on electrical power and energy 5
Last Answer : Problem on electrical power and energy 5

Show More

54 views 1 answer



69 views 0 answers



State the function of following components of a nuclear power station: i) Moderator ii) Shielding iii) Control rod iv) Coolant 
Last Answer : i) Function of Moderator :- Moderator is to moderate or reduce the speed of fast neutron to help the fission process.  ii) Function of sheilding : Shielding is to protect environment, ... from reactor core and transfer it in heat exchanger for producing steam at high pressure and temperature. 

Show More

130 views 1 answer



Explain captive power generation in brief
Last Answer : Advantages of captive power generation:  1. Reliability of supply increases. 2. Power quality is good. (Free from harmonics) 3. Transmission losses reduce as generation is nearby load centre ... . Same steam can be used for generation of electricity. Thus increase efficiency of industry.  

Show More

87 views 2 answers



State the types of radioactive waste generated in a nuclear power station. Explain the methods employed for their disposal.
Last Answer : Types of radioactive waste: The waste produced in nuclear power plant is in the form of solid, liquid & gases, 1. Solid Waste Disposal:-  Solid wastes removed from the reactor are very ... are measured. If it is safe then released to atmosphere at high level through large height chimney.

Show More

132 views 1 answer



"Hydro electric power station are not perennial power station". Justify.
Last Answer : Justification: The water utilized by the hydro power plants comes mostly from storage dams/reservoirs which get filled up during the monsoon rainy season. Such reservoirs are utilized for supplying ... are important. Hence "Hydro electric power stations are not perennial power station" 

Show More

92 views 1 answer



List and state any four limitations of inter connected power station.
Last Answer : Limitations of inter connected power station:- 1) Initial cost of infrastructure of transmission line increases as length increases. 2) Interconnection required more automation which increases cost on ... capacity. But in absence of surplus power merits of interconnection cannot be obtain.

Show More

47 views 1 answer



State the functions of fuel system and exhaust system of a diesel power station.
Last Answer : Fuel system: It supplies fuel to engine for combustion purpose. It consists of Fuel Pump: - It supplies fuel to engine for combustion purpose. Strainer: - Are provided to remove suspended impurities and ... most of the noise. Chimney:- To exhaust gases in the atmosphere as high as possible. 

Show More

97 views 1 answer



State why nuclear power plants are used as base load plants and diesel power plants as a peak load plant. 
Last Answer : 1. Because of following points Nuclear power plant used as base load power plant:-  1. Nuclear power plants is very economical for producing bulk amount of electric power 2. Nuclear power plant is reliable ... . The plants can be put on load easily. 4. Diesel engines take less time to make OFF.

Show More

120 views 1 answer



State the advantages and disadvantages of hydroelectric power plant.
Last Answer : Advantages of Hydroelectric power plant:-  1. There is no air pollution and other environmental problems. 2. The fuel (water) is available freely. 3. No fuel transportation cost so; there is ... , this can force the relocation of large numbers of riverside cities, towns, villages & people.

Show More

89 views 1 answer



State the function of cooling tower and condenser in thermal power station.
Last Answer : 1. Condenser:   Function of condenser is to convert exhaust steam again into water by reducing its temperature with the help of cold water. Also it reduces back pressure of steam turbine 2 ... tower : The function of cooling tower is to reduce the temperature of water coming from condenser.

Show More

319 views 1 answer



State any two applications of diesel power plants.
Last Answer : Applications of Diesel Power Plant: 1. It can be used as a standby (emergency) power plant to maintain continuity of supply. (Incase failure of main supply like hospital, Telephone exchange Radio ... . The diesel units can be used to supply the auxiliaries for starting the large thermal plants.

Show More

84 views 1 answer


Show More⇦ PreviousNext ⇨