A 1000 watts heater is connected to a 240 V AC Supply. Then the current drawn by the heater is

A 1000 watts heater is connected to a 240 V AC Supply. Then the current drawn by the heater is
by

1 Answer

Answer :

A 1000 watts heater is connected to a 240 V AC Supply. Then the current drawn by the heater is 4.166 amperes

by

Related questions

An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes

Description : An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes

Last Answer : Answer: B

What would be the total power drawn from the supply, when two heaters, rated at 1000 W, 250 V each ...

Description : What would be the total power drawn from the supply, when two heaters, rated at 1000 W, 250 V each are connected in series across a 250 V, 50 Hz supply?  (A) 1000 W (B) 500 W (C) 250 W (D) 2000 W

Last Answer : Answer:B. One heater 1000W, 250V resistance is 62.5ohm. Two Series connected heaters so, 62.5+62.5=125ohm. Current in the series circuit is 250V/125ohm = 2A. Total power drawn = current2 X R = 22 x 125 = 500W.

What are the sources of 240 V AC class I supply? What are the functions of each part of UPS?

Description : What are the sources of 240 V AC class I supply? What are the functions of each part of UPS? 

Last Answer : Six sources. Three 20 kVA UPS for safety related loads. Two 60 kVA UPS for non-safety related loads. One 60 kVA UPS as a standby to safety related loads. These all UPS are back up by ... UPS into service. Manual bypass To take main UPS to maintenance by putting stand by UPS into service. 

52 A transformer has 1000 primary turns, connected to 250V ac supply. To get 400V secondary voltage the no of secondary turns should be A. 1600 B. 250 C. 400 D. 1250

Description : 52 A transformer has 1000 primary turns, connected to 250V ac supply. To get 400V secondary voltage the no of secondary turns should be A. 1600 B. 250 C. 400 D. 1250

Last Answer : A. 1600

A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V,

Description : A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum when the supply frequency is 1 kHz. The ... (A) 40, 400 Hz (B) 10, 100 Hz (C) 20, 50 Hz (D) 50, 20 Hz

Last Answer : A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum ... supply frequency is 1 kHz. The approximate values of Q-factor and bandwidth are, respectively 20, 50 Hz

How many amps in a 1000 watts at 110 volts ac?

Description : How many amps in a 1000 watts at 110 volts ac?

Last Answer : 9 amps would be the answer.

A fridge uses 220 watts from 110 V power source. The Fridge then draws a current from the source equal to

Last Answer : A fridge uses 220 watts from 110 V power source. The Fridge then draws a current from the source equal to 2 amps.

If a 220 V heater is used on 110 V supply, the heat produced by it will be nearly

Description : If a 220 V heater is used on 110 V supply, the heat produced by it will be nearly (a) one half (b) twice (c) one-fourth (d) four times 

Last Answer : If a 220 V heater is used on a 110 V supply, the heat produced by it will be significantly less than it would be if it were used on a 220 V supply. This is because the heater is designed to operate ... the heater, but it will be significantly less than it would be if it were used on a 220 V supply.

Two 100 watt light bulbs are connected in parallel across a 100 volt power supply. The total power developed in the circuit is _______________. A. 200 watts B. 100 watts C. 50 watts D. equal to the product of the amperes times the voltage in each branch

Description : Two 100 watt light bulbs are connected in parallel across a 100 volt power supply. The total power developed in the circuit is _______________. A. 200 watts B. 100 watts C. 50 watts D. equal to the product of the amperes times the voltage in each branch

Last Answer : Answer: A

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

What is the effective radiated power of a repeater with 120 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 601 W B. 240 W C. 60 W D. 379 W

Description : What is the effective radiated power of a repeater with 120 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 601 W B. 240 W C. 60 W D. 379 W

Last Answer : C. 60 W

A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the proper connections for across the line starting B. the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Description : A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the ... the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Last Answer : Answer: D

A process electric heater is taking an hour to reach the desired temperature while operating at 440 V. It will take ------- hours to reach the same temperature if the supply voltage is reduced to 220 V. a) 2 b) 3 c) 4 d) 5

Description : A process electric heater is taking an hour to reach the desired temperature while operating at 440 V. It will take ------- hours to reach the same temperature if the supply voltage is reduced to 220 V. a) 2 b) 3 c) 4 d) 5

Last Answer : c) 4

The eddy current loss in an AC motor is 100 watts at 50 Hz. Its losses at 100 Hz will be:

Description : The eddy current loss in an AC motor is 100 watts at 50 Hz. Its losses at 100 Hz will be: (A) 25 watts (B) 59 watts (C) 100 watts (D) 400 watts

Last Answer : The eddy current loss in an AC motor is 100 watts at 50 Hz. Its losses at 100 Hz will be: 400 watts

How many amps will a 230 vac 3500 watts heater draw?

Description : How many amps will a 230 vac 3500 watts heater draw?

Last Answer : Since power = voltage * currentwe have current=power/voltage so 3500 watts/230 volts = about15.218 amperes in a heater using a resistance to generate heat.This should be valid even though the "230 vac" indicates that it isan AC circuit and not a DC circuit.

An immersion heater of 400 watts kept on for 5 hours will consume electrical power of a. 2KWh b. 20KWh c. 6KWh d. 12KWh

Description : An immersion heater of 400 watts kept on for 5 hours will consume electrical power of a. 2KWh b. 20KWh c. 6KWh d. 12KWh

Last Answer : a. 2KWh

A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W....

Description : A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ?  (a) 100 VAR (b) 200 VAR (c) 300 VAR (d) 400 VAR

Last Answer : A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ? 400 VAR

A two-phase generator is connected to two 9012 load resistors. Each coil generates 120 V ac. The value of ...

Description : A two-phase generator is connected to two 90Ω load resistors. Each coil generates 120 V ac. The value of current flowing through the common neutral line will be: A. 1.33 A B. 1.88 A C. 2.66 A D. 1.77 A

Last Answer : A two-phase generator is connected to two 90Ω load resistors. Each coil generates 120 V ac. The value of current flowing through the common neutral line will be: 1.77 A

If there is a reduction in the normally supplied frequency to a 120/240 volt, threephase AC current motor from 60 hertz to 55 hertz, the motor would _____________. A. run at a slower speed B. operate at a lower current C. overheat D. trip off the line

Description : If there is a reduction in the normally supplied frequency to a 120/240 volt, threephase AC current motor from 60 hertz to 55 hertz, the motor would _____________. A. run at a slower speed B. operate at a lower current C. overheat D. trip off the line

Last Answer : Answer: A

What is the amp draw for a 3800 watt 240 volt water heater?

Description : What is the amp draw for a 3800 watt 240 volt water heater?

Last Answer : What is the answer ?

A nichrome heating element connected to a 200 V supply draws an intial current of 2.2 A which settles down after a few seconds to a steady value of 2.

Description : A nichrome heating element connected to a 200 V supply draws an intial current of 2.2 A which settles down after a few seconds to a steady value of 2.

Last Answer : A nichrome heating element connected to a 200 V supply draws an intial current of 2.2 A which settles down after a ... is `1.7xx10^(-4) "per"^(@)C`.

Current in a 60 W light bulb when it is connected to a 230 V power supply is A. 0.26 A B. 1.5 A C. 2.6 A D. 3.9 A

Description : Current in a 60 W light bulb when it is connected to a 230 V power supply is A. 0.26 A B. 1.5 A C. 2.6 A D. 3.9 A

Last Answer : 0.26 A

A series combination of resistance 100 ohm and capacitance 50µf is connected in series to a 230 V, 50HZ supply. Calculate (i) Capacitive reactance (ii) Current (iii) Power factor (iv) Power consumed

Description : A series combination of resistance 100 ohm and capacitance 50µf is connected in series to a 230 V, 50HZ supply. Calculate (i) Capacitive reactance (ii) Current (iii) Power factor (iv) Power consumed 

Last Answer : For RC series circuit

An electric clothes dryer is connected to a 100-volt source. How much current does it use if it requires 2,000 watts of electric power?

Description : An electric clothes dryer is connected to a 100-volt source. How much current does it use if it requires 2,000 watts of electric power?

Last Answer : 20 Amphere

A 35 V dc supply is connected across a resistance of 600 ohm in series with an unknown resistance R. A

Description : A 35 V dc supply is connected across a resistance of 600 ohm in series with an unknown resistance R. A voltmeter having a resistance of 1.2 kOhm is connected across 600 ohm resistances and reads 5 V. The value of resistance R shall be:

Last Answer : A 35 V dc supply is connected across a resistance of 600 ohm in series with an unknown resistance R. A voltmeter having a resistance of 1.2 kOhm is connected across 600 ohm resistances and reads 5 V. The value of resistance R shall be: 2.4 kOhm

If two parallel-connected resistors dissipate 6 watts and 10 watts of power, then what is the total power loss?

Last Answer : If two parallel-connected resistors dissipate 6 watts and 10 watts of power, then 16 watts is the total power loss.

The emf of a cell E is 15 V as shown in the figure with an internal resistance of `0.5Omega`. Then the value of the current drawn from the cell is

Description : The emf of a cell E is 15 V as shown in the figure with an internal resistance of `0.5Omega`. Then the value of the current drawn from the cell is

Last Answer : The emf of a cell E is 15 V as shown in the figure with an internal resistance of `0.5Omega`. Then the value of ... A. `3A` B. `2A` C. `5A` D. `1A`

A loud buzzing noise in an AC controller is probably caused by _____________. A. poor contact with the overload relay B. an incorrectly sized heater C. a broken shading coil D. abnormal starting current

Description : A loud buzzing noise in an AC controller is probably caused by _____________. A. poor contact with the overload relay B. an incorrectly sized heater C. a broken shading coil D. abnormal starting current

Last Answer : Answer: C

When current flows through heater coil it glows but supply wiring does not glow because?

Description : When current flows through heater coil it glows but supply wiring does not glow because?

Last Answer : When current flows through heater coil it glows but supply wiring does not glow because resistance of heater coil is more than the supply wires.

The reactive power drawn by a motor from an AC generator is the power which is _____________. A. used to establish the magnetic field of the motor B. lost in overcoming friction in the bearings C. strictly converted to heat generated by current flow through the windings D. transmitted directly through the rotor shaft to perform useful work

Description : The reactive power drawn by a motor from an AC generator is the power which is _____________. A. used to establish the magnetic field of the motor B. lost in overcoming friction in the ... by current flow through the windings D. transmitted directly through the rotor shaft to perform useful work

Last Answer : Answer: A

A battery of 40 V and three capacitors of 1000 μF, 500 μF and 100 μF are all connected in

Description : A battery of 40 V and three capacitors of 1000 μF, 500 μF and 100 μF are all connected in (I) parallel and (II) series. The ratio of total charge stored in case I to that in case II is approximately  (a) 3 : 64 (b) 64 : 3 (c) 160 : 3 (d) 104 : 5

Last Answer : A battery of 40 V and three capacitors of 1000 μF, 500 μF and 100 μF are all connected in (I) parallel and (II) series. The ratio of total charge stored in case I to that in case II is approximately 104 : 5

Two heaters, rated at 1000 W, 250 V each are connected in series across...

Description : Two heaters, rated at 1000 W, 250 V each are connected in series across a 250 V, 50 Hz ac mains. The total power drawn from the supply would be __________ watt.

Last Answer : Two heaters, rated at 1000 W, 250 V each are connected in series across a 250 V, 50 Hz ac mains. The total power drawn from the supply would be 500 watt.

How many watts is 1000 MA?

Description : How many watts is 1000 MA?

Last Answer : Watts, a measure of electrical power) is a function of (dependson) current and voltage as in watts = current (MA) * Volts. Sinceno voltage was given, the question can not be answeredproperly.If the voltage was ... as1000 MA), it would be 100 watts. If it was 10 Volts, the answerwould be 10 Watts.

The range of speech power is ____. A. 1 – 10 watts B. 100 – 1000 milliwatts C. 10 – 100 milliwatts D. 10 – 1000 microwatts

Description : The range of speech power is ____. A. 1 – 10 watts B. 100 – 1000 milliwatts C. 10 – 100 milliwatts D. 10 – 1000 microwatts

Last Answer : 10 – 1000 microwatts

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Description : An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Last Answer : Solution:

An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to

Description :  An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

Last Answer :  An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge

Description : A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge converter. A large inductance is connected in the dc circuit to maintain the dc current at 20 A ... thyristor will be reverse biased for a period of  (A) 125o (B) 120o (C) 60o (D) 55o

Last Answer : A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge converter. A large inductance is connected in the dc circuit to maintain the ... the solar cell resistance is 0.5 Ohm ,then each thyristor will be reverse biased for a period of 125o

In an L-C -R search circuit connected to an AC source `V=V_(0)sin(100pi+(pi)/(6))``V_(R)=40V, V_(L)=40 and V_(C )=10V`, resistance `R=4Omega` Choose t

Description : In an L-C -R search circuit connected to an AC source `V=V_(0)sin(100pi+(pi)/(6))``V_(R)=40V, V_(L)=40 and V_(C )=10V`, resistance `R=4Omega` Choose t

Last Answer : In an L-C -R search circuit connected to an AC source `V=V_(0)sin(100pi+(pi)/(6))``V_(R)=40V, V_ ... (a) and (b) are correct D. Both a and b are wrong

In an L-C -R series circuit connected to an AC source `V=V_(0)sin(100pi(t)+(pi)/(6))``V_(R)=40V, V_(L)=40 and V_(C )=10V`, resistance `R=4Omega` Choos

Description : In an L-C -R series circuit connected to an AC source `V=V_(0)sin(100pi(t)+(pi)/(6))``V_(R)=40V, V_(L)=40 and V_(C )=10V`, resistance `R=4Omega` Choos

Last Answer : In an L-C -R series circuit connected to an AC source `V=V_(0)sin(100pi(t)+(pi)/(6))``V_(R)=40V, V_(L) ... (2) A` C. `20sqrt(2) A` D. `25sqrt(2) A`

The primary coil of a transformer is connected to a 60 V ac source. The secondary coil is connected to a 330

Description : The primary coil of a transformer is connected to a 60 V ac source. The secondary coil is connected to a 330 ohms load. The turns ratio is 3:1. What is the secondary voltage? A.2 V B.20 V C.180 V D.18 V

Last Answer : The primary coil of a transformer is connected to a 60 V ac source. The secondary coil is connected to a 330 ohms load. The turns ratio is 3:1. What is the secondary voltage? A.2 V B.20 V C.180 V D.18 V

Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor

Description : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

Last Answer : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

ABCD is a parallelogram with diagonal AC If a line XZ is drawn such that XZ ∥ AB, then BX/XC = ? (a) (AY/AC) (b) DZ/AZ (c) AZ/ZD (d) AC/AY Answer: (c) AZ/ZD 13. In the given figure, value of x (in cm) is (a) 5cm (b) 3.6 cm (c) 3.2 cm (d) 10 cm

Description : ABCD is a parallelogram with diagonal AC If a line XZ is drawn such that XZ ∥ AB, then BX/XC = ? (a) (AY/AC) (b) DZ/AZ (c) AZ/ZD (d) AC/AY Answer: (c) AZ/ZD 13. In the given figure, value of x (in cm) is (a) 5cm (b) 3.6 cm (c) 3.2 cm (d) 10 cm

Last Answer : (a) 5cm

How many watts does the charger of Nokia phone type AC-8E consume?

Description : How many watts does the charger of Nokia phone type AC-8E consume?

Last Answer : answer:You can do the conversion here. But the answer is: 0.15 watts.

How many watts to run 11000 btu ac?

Description : How many watts to run 11000 btu ac?

Last Answer : Need answer

A dc voltmeter has a sensitivity of 1000 Ohm/V. When it measures half full scale in 100 V range, the current ...

Description : A dc voltmeter has a sensitivity of 1000 Ohm/V. When it measures half full scale in 100 V range, the current through the voltmeter is

Last Answer : A dc voltmeter has a sensitivity of 1000 Ohm/V. When it measures half full scale in 100 V range, the current through the voltmeter is 1 mA.

A battery of emf E has an internal resistance r. A variable resistacne R is connected to the terminals of the battery. A current `i` is drawn from the

Description : A battery of emf E has an internal resistance r. A variable resistacne R is connected to the terminals of the battery. A current `i` is drawn from the

Last Answer : A battery of emf E has an internal resistance r. A variable resistacne R is connected to the terminals of ... infinity, `(E)/(r)`, V approaches E

What is the maximum current allowed to be drawn from the secondary of a 2 KVA step-down transformer with a turns ratio of four to one if connected across a 440 volt line? A. 1.1 amps B. 4.5 amps C. 18.1 amps D. 22.7 amps

Description : What is the maximum current allowed to be drawn from the secondary of a 2 KVA step-down transformer with a turns ratio of four to one if connected across a 440 volt line? A. 1.1 amps B. 4.5 amps C. 18.1 amps D. 22.7 amps

Last Answer : Answer: C

In a load flow analysis of a power system, the load connected at a bus is represented as a) Constant current drawn from the bus b) Constant impedance connected at the bus c) Voltage and frequency dependent sources at the boss d) Constant real and reactive power drawn from the bus

Description : In a load flow analysis of a power system, the load connected at a bus is represented as a) Constant current drawn from the bus b) Constant impedance connected at the bus c) Voltage and frequency dependent sources at the boss d) Constant real and reactive power drawn from the bus

Last Answer : d) Constant real and reactive power drawn from the bus

What is the capacitance when a capacitor passes a current of 31.43 mA when supplied with 40 V AC with a

Description : What is the capacitance when a capacitor passes a current of 31.43 mA when supplied with 40 V AC with a frequency of 1000 Hz? A) 0.125 F B) 0.125 μF C) 1257.2 μF D) None of these

Last Answer : What is the capacitance when a capacitor passes a current of 31.43 mA when supplied with 40 V AC with a frequency of 1000 Hz? A) 0.125 F B) 0.125 μF C) 1257.2 μF D) None of these

A filament bulb `(500 W, 100 V)` is to be used in a `230 V` main supply. When a resistance `R` is connected in series, it works perfectly and the bulb

Description : A filament bulb `(500 W, 100 V)` is to be used in a `230 V` main supply. When a resistance `R` is connected in series, it works perfectly and the bulb

Last Answer : A filament bulb `(500 W, 100 V)` is to be used in a `230 V` main supply. When a resistance `R` is ... Omega` B. `46 Omega` C. `26Omega` D. `13 Omega`