What is the primary difference between the NPN and PNP amplifiers?

What is the primary difference between the NPN and PNP  amplifiers?
by

1 Answer

Answer :

The polarity of the source voltage
by

Related questions

What is the relationship between the polarity of the voltage applied to the PNP transistor and that applied to the NPN transistor?

Description : What is the relationship between the polarity of the voltage applied to the PNP transistor and that applied to the NPN transistor?

Last Answer : The polarity of voltage applied to the PNP transistor is opposite of that applied to the NPN

An important characteristic of the device shown in figure 'B' of the illustration as compared with conventional NPN or PNP transistors is its ____________. EL-0065 A. higher temperature sensitivity B. higher power ratings C. very high input resistance D. all of the above

Description : An important characteristic of the device shown in figure 'B' of the illustration as compared with conventional NPN or PNP transistors is its ____________. EL-0065 A. higher temperature sensitivity B. higher power ratings C. very high input resistance D. all of the above

Last Answer : Answer: C

PNP and NPN transistor:

Description : PNP and NPN transistor:

Last Answer : PNP transistors is the one in which one N, type semiconductor is sandwiched in between two P type or accepter diodes while NPN transistor is the one in which two N type semiconductors are fitted on the both sides of p-type semiconductor to allow to pass current from them.

In a transistor, the conventional current flows from base to emitter. The transistor is (a) NPN (b) PNP (c) FET (d) None of these

Description : In a transistor, the conventional current flows from base to emitter. The transistor is (a) NPN (b) PNP (c) FET (d) None of these

Last Answer : (a) NPN

Draw symbol of NPN and PNP transistors.

Description : Draw symbol of NPN and PNP transistors. 

Last Answer : symbol of NPN and PNP transistors

In a BJT circuit a pnp transistor is replaced by npn transistor. To analyse the new circuit

Description : In a BJT circuit a pnp transistor is replaced by npn transistor. To analyse the new circuit (1) All calculations done earlier have to be repeated (2) Replace all calculated voltages by ... all calculated currents by reverse values (4) Replace all calculated voltages and currents by reverse values 

Last Answer : In a BJT circuit a pnp transistor is replaced by npn transistor. To analyse the new circuit  Replace all calculated voltages and currents by reverse values 

Most of the transistors are NPN type and not PNP type because

Description : Most of the transistors are NPN type and not PNP type because  1.NPN transistor gives large voltage gain 2.NPN transistors are more negative than PNP transistors 3.In NPN transistor, the current ... free electrons which are less mobiles than holes 4.We can have high conduction is NPN transistors 

Last Answer : Most of the transistors are NPN type and not PNP type because We can have high conduction is NPN transistors 

What are the majority current carriers in a PNP transistor?

Description : What are the majority current carriers in a PNP transistor?

Last Answer : Holes.

What percentage of current in an NPN transistor reaches the collector?

Description : What percentage of current in an NPN transistor reaches the collector?

Last Answer : 98 percent.

In the NPN transistor, what section is made very thin compared with the other two sections?

Description : In the NPN transistor, what section is made very thin compared with the other two sections?

Last Answer : The P or base section.

To properly bias an NPN transistor, what polarity voltage is applied to the collector, and what is its relationship to the base voltage?

Description : To properly bias an NPN transistor, what polarity voltage is applied to the collector, and what is its relationship to the base voltage?

Last Answer : Positive, more positive.

In which direction does the arrow point on an NPN transistor?

Description : In which direction does the arrow point on an NPN transistor?

Last Answer : Outward.

What is the polarity of the first alternation of the tank circuit in an emitter-loaded npn pulsed oscillator?

Description : What is the polarity of the first alternation of the tank circuit in an emitter-loaded npn pulsed oscillator?

Last Answer : Negative

List two common usages of magnetic amplifiers

Description : List two common usages of magnetic amplifiers

Last Answer : Servosystems, temperature recorders, or power supplies

The IF amplifiers are connected in what amplifier configuration?

Description : The IF amplifiers are connected in what amplifier configuration?

Last Answer : Cascade.

In what two ways are amplifiers classified?

Description : In what two ways are amplifiers classified?

Last Answer : By function and frequency response.

Why do electronic devices use amplifiers?

Description : Why do electronic devices use amplifiers?

Last Answer : To amplify the input signal to a usable level.

What is the full form of 'PnP' ? -How To ?

Description : What is the full form of 'PnP' ? -How To ?

Last Answer : The full form of 'PnP' is Plug and Play

What is the full form of PnP ?

Last Answer : Plug 'n Play

As shown in the illustration, which electrical symbol represents a PNP type semiconductor? EL-0065 A. A B. B C. C D. D

Description : As shown in the illustration, which electrical symbol represents a PNP type semiconductor? EL-0065 A. A B. B C. C D. D

Last Answer : Answer: C

As shown in the illustration, which of the elements listed does the line 'B' represent in the basic schematic symbol of a PNP transistor? EL-0068 A. Base B. Emitter C. Cathode D. Collector

Description : As shown in the illustration, which of the elements listed does the line 'B' represent in the basic schematic symbol of a PNP transistor? EL-0068 A. Base B. Emitter C. Cathode D. Collector

Last Answer : Answer: D

Which of the following statements correctly applies to transistors? A. NDN and PNP are the two basic types of transistors. B. The three terminals are called the emitter, base, and collector. C. The emitter separates the base and collector. D. The collector separates the emitter and base.

Description : Which of the following statements correctly applies to transistors? A. NDN and PNP are the two basic types of transistors. B. The three terminals are called the emitter, base, and collector. C. The emitter separates the base and collector. D. The collector separates the emitter and base.

Last Answer : Answer: B

Explain the operating principle of PNP transistor.

Description : Explain the operating principle of PNP transistor. 

Last Answer : The circuit connection of PNP transistor with supply voltages is as shown above. The emitter-base junction is connected as forward bias. Due to this the emitter pushes the holes from the P ... by the collector. This develops the collector current IC. This is how a PNP transistor operates. 

A “PNP” transistor is made of

Last Answer : A “PNP” transistor is made of Either Ge (or) Si

When an NPN transistor is saturated its Vce?

Description : When an NPN transistor is saturated its Vce?

Last Answer : is zero

A triac thyristor functions as a control device and is basically ________________. A. two NPN transistors in parallel with a common base lead B. a diode in series with a temperature sensitive capacitor C. two back-to-back SCR's with a common gate lead D. a triode tube with an extra heavy grid element

Description : A triac thyristor functions as a control device and is basically ________________. A. two NPN transistors in parallel with a common base lead B. a diode in series with a temperature sensitive capacitor C. two ... -back SCR's with a common gate lead D. a triode tube with an extra heavy grid element

Last Answer : Answer: C

Which of the symbols shown in the illustration represents an NPN type transistor? EL-0078 A. A B. B C. C D. D

Description : Which of the symbols shown in the illustration represents an NPN type transistor? EL-0078 A. A B. B C. C D. D

Last Answer : Answer: B

If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the input signal C) Need for high dc collector supply D) Clipping of output in the negative half of the input signal

Description : If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the ... for high dc collector supply D) Clipping of output in the negative half of the input signal

Last Answer : B) Clipping of output in the positive half of the input signal

Draw the construction of BJT (NPN) and explain its working principle. State and explain different operating regions.

Description : Draw the construction of BJT (NPN) and explain its working principle. State and explain different operating regions.

Last Answer : Construction of BJT (NPN): Working of NPN Transistor : The circuit diagram of the NPN transistor is shown in the figure below. The forward biased is applied across the emitter-base ... Zero with input current is Zero transistor in cut off. In this region transistor act as open switch

Draw symbol of NPN transistor and state three configurations of transistor (BJT)

Description : Draw symbol of NPN transistor and state three configurations of transistor (BJT)

Last Answer : Configuration - Common Emitter Common Collector Common Base

With neat diagram explain working of NPN transistor.

Description : With neat diagram explain working of NPN transistor.

Last Answer : N-p-n transistor is made by sandwiching thin layer of p-type semiconductor between two layers of n-type semiconductor. It has three terminals - Emitter, Base and collector. The npn transistor has two ... up in the collector as it is more positive. In this way, current flows in the transistor.

When an NPN transistor is properly biased then most of the electrons from the emitter

Description : When an NPN transistor is properly biased then most of the electrons from the emitter   (A) recombine with holes in the base (B) recombine in the emitter itself (C) pass through the base to the collector (D) are stopped by the junction barrier

Last Answer : a

In an npn transistor, _____ are the minority carriers.

Description : In an npn transistor, _____ are the minority carriers.   (a) Free electrons (b) Acceptor ions (c) Donor ions (d) Holes

Last Answer : In an npn transistor, Holes are the minority carriers.

Common basic applications for the operational amplifier include ____________. A. counting, pulsing and clocking amplifiers B. summing, scaling and difference amplifiers C. step-up, step-down and rectifying amplifiers D. all of the above

Description : Common basic applications for the operational amplifier include ____________. A. counting, pulsing and clocking amplifiers B. summing, scaling and difference amplifiers C. step-up, step-down and rectifying amplifiers D. all of the above

Last Answer : Answer: B

What is the primary difference between the radio horizon and the natural horizon?

Description : What is the primary difference between the radio horizon and the natural horizon?

Last Answer : Sea water.

What is the primary difference between the pump signal of a simple parametric amplifier and the pump signal of a nondegenerative parametric amplifier?

Description : What is the primary difference between the pump signal of a simple parametric amplifier and the pump signal of a nondegenerative parametric amplifier?

Last Answer : The pump signal of a nondegenerative parametric amplifier is higher than twice the input signal.

What is the primary difference in construction between the basic magnetron and the negativeresistance magnetron?

Description : What is the primary difference in construction between the basic magnetron and the negativeresistance magnetron?

Last Answer : The negative-resistance magnetron has a split plate

What is the primary difference between a diode and a triode?

Description : What is the primary difference between a diode and a triode?

Last Answer : The triode contains a third element called the control rid.

What is the primary difference between the major and minor lobes of a radiation pattern?

Description : What is the primary difference between the major and minor lobes of a radiation pattern?

Last Answer : Major lobes have the greatest amount of radiation.

Is it possible to bridge an odd number of amplifiers?

Description : Is it possible to bridge an odd number of amplifiers?

Last Answer : No. That's not possible. Amplifiers can only be bridged in pairs, and pairs of pairs, etc. And if they're not identical amps, you're asking for trouble, too. Some stereo amplifiers are wired so that you ... 4-channel, and he's bridging them in some odd way to create a balanced pair of pair of amps.

What are antenna amplifiers used for?

Description : What are antenna amplifiers used for?

Last Answer : Antenna amplifiers are used to strengthen the signal being supplied to an appliance such as your TV. Amplifiers are necessary when the signal is weak and interferes with your TV reception.

Can I get government assistance if I am deaf and need phone amplifiers?

Description : Can I get government assistance if I am deaf and need phone amplifiers?

Last Answer : Some states do have assistance available-- Nevada and Nebraska are two examples. Help from the Federal Government directly is not available through Medicare or the National Institute on Deafness and Other ... do have a directory of local groups that will help-- www.nidcd.nih.gov/directory/

Are phone amplifiers bad for your hearing?

Description : Are phone amplifiers bad for your hearing?

Last Answer : They can be bad for your hearing if they are putting out more than 105 dB. 10 minutes of noise at 105 dB can damage your hearing. Though minor damage can be repaired by itself, repeatedly getting minor damage adds up to major damage and hearing loss.

Are car amplifiers just about volume, or do they improve sound quality, as well?

Description : Are car amplifiers just about volume, or do they improve sound quality, as well?

Last Answer : Cap amplifiers can provide an enhanced audio experience as they often are able to reproduce a wider range of audio frequencies compared to many stock car stereos.

Does the volume go to "11" on any car amplifiers?

Description : Does the volume go to "11" on any car amplifiers?

Last Answer : No. Police can pull you over for noise pollution so they tend not to make them do higher.

Which car amplifiers work best with MP3 files?

Description : Which car amplifiers work best with MP3 files?

Last Answer : Pioneer is the best amplifer and car system that works with MP3 files.

Are the amplifiers easy to remove?

Description : Are the amplifiers easy to remove?

Last Answer : Yes it's easy to remove amplifiers from your car. First make sure the fuse is out of the power wire , so the wire is not live. Then disconnect the wires from your amp. Then unscrew the amp from where it's mounted.

Are there special amplifiers for hybrid and electric vehicles?

Description : Are there special amplifiers for hybrid and electric vehicles?

Last Answer : Yes, they draw power differently as to not kill the engine.

Negative feedback in amplifiers – (1) increases bandwidth and decreases noise (2) decreases bandwidth and decreases noise (3) increases bandwidth and in-creases noise (4) decreases bandwidth and increases noise

Description : Negative feedback in amplifiers – (1) increases bandwidth and decreases noise (2) decreases bandwidth and decreases noise (3) increases bandwidth and in-creases noise (4) decreases bandwidth and increases noise

Last Answer : (1) increases bandwidth and decreases noise Explanation: Voltage gain, input impedance, output impedance, bandwidth etc. are few important characteristics of an amplifier. These parameters are more or ... be controlled. This can be conveniently achieved by employing a technique, called the feedback.

Negative feedback in amplifiers – (1) increases bandwidth and decreases noise (2) decreases bandwidth and decreases noise (3) increases bandwidth and in-creases noise (4) decreases bandwidth and increases noise

Description : Negative feedback in amplifiers – (1) increases bandwidth and decreases noise (2) decreases bandwidth and decreases noise (3) increases bandwidth and in-creases noise (4) decreases bandwidth and increases noise

Last Answer : (1) increases bandwidth and decreases noise Explanation: Voltage gain, input impedance, output impedance, bandwidth etc. are few important characteristics of an amplifier. These parameters are more or ... be controlled. This can be conveniently achieved by employing a technique, called the feedback.