In general, MOV devices are used to protect electronic equipment from dangerous operating conditions such as A) High temperatures B) Line transients C) Over current D) All of the above.

In general, MOV devices are used to protect electronic equipment from dangerous operating conditions such as
A) High temperatures
B) Line transients
C) Over current
D) All of the above.
by

1 Answer

Answer :

D) All of the above.
by

Related questions

Load regulation is a measure of a power supplies ability keep a constant output under conditions of changing A) Line voltage B) Current demand C) Temperature D) Oscillator frequency.

Description : Load regulation is a measure of a power supplies ability keep a constant output under conditions of changing A) Line voltage B) Current demand C) Temperature D) Oscillator frequency.

Last Answer : A) Line voltage

If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the input signal C) Need for high dc collector supply D) Clipping of output in the negative half of the input signal

Description : If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the ... for high dc collector supply D) Clipping of output in the negative half of the input signal

Last Answer : B) Clipping of output in the positive half of the input signal

What conditions are required for an amplifier to oscillate A) There must be feedback B) The feedback must be in phase C) The gain must be greater than the loss D) All the above are regd.

Description : What conditions are required for an amplifier to oscillate A) There must be feedback B) The feedback must be in phase C) The gain must be greater than the loss D) All the above are regd.

Last Answer : B) The feedback must be in phase

The ideal characteristic of a voltage stablizer is A) constant output voltage with low internal resistance B) constant output current with low internal resistance C) constant output voltage with high internal resistance D) constant internal resistance with variable output voltage.

Description : The ideal characteristic of a voltage stablizer is A) constant output voltage with low internal resistance B) constant output current with low internal resistance C) constant output voltage with high internal resistance D) constant internal resistance with variable output voltage.

Last Answer : A) constant output voltage with low internal resistance

The change in base current will be A) 0.66 micro ampere B) 6.6 micro amperes C) 66 micro amperes D) 660 micro amperes.

Description : The change in base current will be A) 0.66 micro ampere B) 6.6 micro amperes C) 66 micro amperes D) 660 micro amperes.

Last Answer : A) 0.66 micro ampere

As compared to a CB amplifier, a CE amplifier has A) Lower current amplification B) Higher current amplification C) Higher input resistance. D) Both (B) & (C)

Description : As compared to a CB amplifier, a CE amplifier has A) Lower current amplification B) Higher current amplification C) Higher input resistance. D) Both (B) & (C)

Last Answer : D) Both (B) & (C)

Foldback current limiting has the advantage of A) Better pass transistor protection for long term overloads B) A defined turn on point C) Circuit simplicity D) All of the above.

Description : Foldback current limiting has the advantage of A) Better pass transistor protection for long term overloads B) A defined turn on point C) Circuit simplicity D) All of the above.

Last Answer : A) Better pass transistor protection for long term overloads

A crow bar is a power supply circuit that provides A) Conventional current limiting B) Foldback current. limiting C) Temperature control D) Voltage limiting.

Description : A crow bar is a power supply circuit that provides A) Conventional current limiting B) Foldback current. limiting C) Temperature control D) Voltage limiting.

Last Answer : D) Voltage limiting.

Current limited power supplies can prevent damage to A) Rectifier diodes and power transformers. B) Pass transistors C) Other circuits in the system D) All of the above.

Description : Current limited power supplies can prevent damage to A) Rectifier diodes and power transformers. B) Pass transistors C) Other circuits in the system D) All of the above.

Last Answer : D) All of the above.

In a resistance loaded amplifier, the gain decreases a high frequencies because A) Of decreasing reactance of the stray CT B) Increasing reactance of the stray CT C) Increasing reactance of CC D) Decreasing reactance of CC.

Description : In a resistance loaded amplifier, the gain decreases a high frequencies because A) Of decreasing reactance of the stray CT B) Increasing reactance of the stray CT C) Increasing reactance of CC D) Decreasing reactance of CC.

Last Answer : D) Decreasing reactance of CC.

Common base configuration is little used because A) It has low input impedance B) It has high input impedance C) It does not heat up D) It has very high gain.

Description : Common base configuration is little used because A) It has low input impedance B) It has high input impedance C) It does not heat up D) It has very high gain.

Last Answer : A) It has low input impedance

The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency end and bypass capacitors at the low frequency end C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and D) shunt capacitors at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Description : The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency ... at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Last Answer : C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and

In an amplifier if conductor during the cycle is from 0 to 90° and again from 180° to 270°, the amplifier will be termed as A) Class A B) Class B C) Class C D) Class AB.

Description : In an amplifier if conductor during the cycle is from 0 to 90° and again from 180° to 270°, the amplifier will be termed as A) Class A B) Class B C) Class C D) Class AB.

Last Answer : B) Class B

Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Description : Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Last Answer : A) Wave traps in each stage

Which distortion is least objectionable in case of audio amplifers? A) Phase distortion B) Frequency distortion C) Harmonic distortion D) Inter modulation distortion.

Description : Which distortion is least objectionable in case of audio amplifers? A) Phase distortion B) Frequency distortion C) Harmonic distortion D) Inter modulation distortion.

Last Answer : A) Phase distortion

A push pull amplifier balances out A) Odd harmonics B) Even harmonics C) Both odd as well as even harmonics D) Neither odd nor even harmonics.

Description : A push pull amplifier balances out A) Odd harmonics B) Even harmonics C) Both odd as well as even harmonics D) Neither odd nor even harmonics.

Last Answer : A) Odd harmonics

Which amplifier will be preferred for highest gain? A) Darlington's pair B) Cascade amplifier C) Cascode amplifier D) Depends on the circuitry

Description : Which amplifier will be preferred for highest gain? A) Darlington's pair B) Cascade amplifier C) Cascode amplifier D) Depends on the circuitry

Last Answer : C) Cascode amplifier

Which of the following contributes to harmonics distortion in amplifiers? A) Positive feedback B) Presence of noise C) Defective active device D) Non linearity in active device.

Description : Which of the following contributes to harmonics distortion in amplifiers? A) Positive feedback B) Presence of noise C) Defective active device D) Non linearity in active device.

Last Answer : D) Non linearity in active device.

In an amplifier the collector voltage equals the full V+ of 28 V instead of the normal 12 V which of the following can be the trouble? A) RL is open B) Cc is open C) RE is open D) CE is shorted.

Description : In an amplifier the collector voltage equals the full V+ of 28 V instead of the normal 12 V which of the following can be the trouble? A) RL is open B) Cc is open C) RE is open D) CE is shorted.

Last Answer : B) Cc is open

An ideal voltage amplifier should have A) Ri = 0, R0 = 0 B) Ri = 0, R0 =∞ C) Ri = ∞, R0 = 0 D) Ri = ∞, R0 = ∞.

Description : An ideal voltage amplifier should have A) Ri = 0, R0 = 0 B) Ri = 0, R0 =∞ C) Ri = ∞, R0 = 0 D) Ri = ∞, R0 = ∞.

Last Answer : C) Ri = ∞, R0 = 0

A IGFET is a A) Linear device B) Square law device C) Half power device D) 3/2 power law device.

Description : A IGFET is a A) Linear device B) Square law device C) Half power device D) 3/2 power law device.

Last Answer : B) Square law device

An FET has a gate source bias of 2 V. The ac input signal is ± 1.2 V. The class of operation is A) A B) B C) C D) AB

Description : An FET has a gate source bias of 2 V. The ac input signal is ± 1.2 V. The class of operation is A) A B) B C) C D) AB

Last Answer : D) AB

In a resistance loaded, RC coupled amplifier the dc component is blocked by A) Load resistance RL B) Coupling capacitor, CC C) RB D) The transistor.

Description : In a resistance loaded, RC coupled amplifier the dc component is blocked by A) Load resistance RL B) Coupling capacitor, CC C) RB D) The transistor.

Last Answer : B) Coupling capacitor, CC

Which of the following combinations has no phase inversion of the signal? A) Two CE stages B) CE and CC stages C) Three CE stages D) CE stage and emitter follower.

Description : Which of the following combinations has no phase inversion of the signal? A) Two CE stages B) CE and CC stages C) Three CE stages D) CE stage and emitter follower.

Last Answer : A) Two CE stages

The Darlington pair consists of the following two stages A) CE and CC B) Both C) Both CC D) CE and CB

Description : The Darlington pair consists of the following two stages A) CE and CC B) Both C) Both CC D) CE and CB

Last Answer : C) Both CC

Which of the following circuit would be preferred for a 455 kHz IF amplifier? A) A resistance loaded B) Double tuned transformer C) Video amplifier D) Class C

Description : Which of the following circuit would be preferred for a 455 kHz IF amplifier? A) A resistance loaded B) Double tuned transformer C) Video amplifier D) Class C

Last Answer : B) Double tuned transformer

What is the phase relationship of the signal at the collector of Q2 to the signal at the collector of Q, A) 0° B) 90° C) 180° D) 360°.

Description : What is the phase relationship of the signal at the collector of Q2 to the signal at the collector of Q, A) 0° B) 90° C) 180° D) 360°.

Last Answer : C) 180°

A series mode crystal is marked 10.000 MHz., It is used in a circuit that operates the crystal in its parallel mode. The circuit can be expected to A) Run below 10 MHz B) Run at 10 MHz C) Run above 10 MHz D) Not oscillate.

Description : A series mode crystal is marked 10.000 MHz., It is used in a circuit that operates the crystal in its parallel mode. The circuit can be expected to A) Run below 10 MHz B) Run at 10 MHz C) Run above 10 MHz D) Not oscillate.

Last Answer : C) Run above 10 MHz

Six (6) MHz crystal oscillator has a stability of 1 part in 106. The largest frequency error expected of this crystals A) 0.06 Hz B) 0.6 Hz C) 6 Hz D) 60 Hz.

Description : Six (6) MHz crystal oscillator has a stability of 1 part in 106. The largest frequency error expected of this crystals A) 0.06 Hz B) 0.6 Hz C) 6 Hz D) 60 Hz.

Last Answer : C) 6 Hz

An oscillator that uses crystal control should be A) Frequency stable B) useful only at low frequencies C) AVFO D) none of the above.

Description : An oscillator that uses crystal control should be A) Frequency stable B) useful only at low frequencies C) AVFO D) none of the above.

Last Answer : A) Frequency stable

The major function of transistor. Q2 is A) It provides voltage gain B) It provides the feedback signal C) It isolates the oscillator from loading effects D) It provides a phase shift.

Description : The major function of transistor. Q2 is A) It provides voltage gain B) It provides the feedback signal C) It isolates the oscillator from loading effects D) It provides a phase shift.

Last Answer : ) It provides a phase shift.

Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Description : Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Last Answer : C) All oscillators generate sine waves

To protect most of the electrical equipment handling low power, the types of relays used are (a) thermocouple (b) electronic and bimetallic (c) both (a) and (b) (d) none of the above

Description : To protect most of the electrical equipment handling low power, the types of relays used are (a) thermocouple (b) electronic and bimetallic (c) both (a) and (b) (d) none of the above

Last Answer : (c) both (a) and (b)

Sources of impulse noise induced in communication channels. A. Erroneous digital coding bit caused by an error on a transmission facility B. Transients due to relay operation C. Crosstalk from dc signaling systems D. All of these

Description : Sources of impulse noise induced in communication channels. A. Erroneous digital coding bit caused by an error on a transmission facility B. Transients due to relay operation C. Crosstalk from dc signaling systems D. All of these

Last Answer : D. All of these

________ is a quantitative measure of how fair the transients die cut in the system. (a) Absolutely stable (b) Conditionally stable (c) Unstable (d) Relative stability

Description : ________ is a quantitative measure of how fair the transients die cut in the system. (a) Absolutely stable (b) Conditionally stable (c) Unstable (d) Relative stability

Last Answer : (d) Relative stability

There are no transients in pure resistance circuits because they

Description : There are no transients in pure resistance circuits because they (a) Offer high resistance (b) Obey Ohm's law (c) Have no stored energy (d) Are linear circuits

Last Answer : There are no transients in pure resistance circuits because they Have no stored energy

What causes transients?

Description : What causes transients?

Last Answer : Transient is a peak voltage take small period. It will occur due to lightning

How can I determine who created a type of computer file, such as jpegs and .mov files?

Description : How can I determine who created a type of computer file, such as jpegs and .mov files?

Last Answer : answer:Yes. Examine the email source code and trace the path it took and where it really came from. The files do not have serial #s. If they are photos they may have EXIF info but that won't be ... -on the drop down next to reply' select show original' Don't open the files. Tracing IP addresses

Out of the following gas-liquid contacting devices, for a given set of operating conditions, gas pressure drop is the least in __________ tower. (A) Wetted wall (B) Bubble cap (C) Perforated tray (D) Packed

Description : Out of the following gas-liquid contacting devices, for a given set of operating conditions, gas pressure drop is the least in __________ tower. (A) Wetted wall (B) Bubble cap (C) Perforated tray (D) Packed

Last Answer : (A) Wetted wall

When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only and a low resistance meter for DC measurements C. whenever a low impedance meter is not available, regardless of the components being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Description : When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only ... being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Last Answer : Answer: D

Light Emitting Diodes (LED) is used in fancy electronic devices such as toys emit (1) X-rays (2) ultraviolet light (3) (4) All of the above (4) radio waves

Description : Light Emitting Diodes (LED) is used in fancy electronic devices such as toys emit (1) X-rays (2) ultraviolet light (3) (4) All of the above (4) radio waves

Last Answer : (4) All of the above Explanation: A light-emitting diode (LED) is a semiconductor light source that emits light when current flows through it. Infrared LEDs are used in remote-control circuits, such as those used with a wide variety of consumer electronics.

_________ are specially designed computer chips that reside inside o ther devices, such as your car or your electronic thermostat a) Servers b) Embedded computers c) Robotic computers d) Mainframes e) None of these

Description : _________ are specially designed computer chips that reside inside o ther devices, such as your car or your electronic thermostat a) Servers b) Embedded computers c) Robotic computers d) Mainframes e) None of these

Last Answer : b) Embedded computers

how do i protect carob tree from freezing temperatures and wind from the mountains?

Description : how do i protect carob tree from freezing temperatures and wind from the mountains?

Last Answer : When temperature drops below freezing in Las Vegas, carob trees loose all there leaves. How do I probect them???

Electrical machinery insulation will break down more rapidly due to _________________. A. low loading of motors and generators B. frequent megger testing C. high temperatures and vibration D. high operating frequencies

Description : Electrical machinery insulation will break down more rapidly due to _________________. A. low loading of motors and generators B. frequent megger testing C. high temperatures and vibration D. high operating frequencies

Last Answer : Answer: C

In the illustrated electronic governor, the circuit card connected to the potential and current transformers is for ________. EL-0046 A. increasing the signal strength to the governor to maintain constant engine speed with increased load B. send a kilowatt signal to the metering circuit C. shutting down the prime mover in the event of reverse power to protect from motorization D. conditioning the load through the use of a magnetic amplifier current transformer

Description : In the illustrated electronic governor, the circuit card connected to the potential and current transformers is for ________. EL-0046 A. increasing the signal strength to the governor to ... from motorization D. conditioning the load through the use of a magnetic amplifier current transformer

Last Answer : Answer: A

Which of the following conditions indicates that a lead-acid battery is being charged too rapidly? A. Sparks occurring at the positive terminal. B. Unusually high electrolyte specific gravity. C. Low plate potentials being developed. D. Excessively high temperatures and gassing rates.

Description : Which of the following conditions indicates that a lead-acid battery is being charged too rapidly? A. Sparks occurring at the positive terminal. B. Unusually high electrolyte specific gravity. C. Low plate potentials being developed. D. Excessively high temperatures and gassing rates.

Last Answer : Answer: D

Using a fuse whose rating is higher than necessary ________. A. endangers the apparatus it is supposed to protect B. reduces the possibility of short circuits C. increases the efficiency of the equipment by allowing more current to be used D. wastes money because they are more expensive

Description : Using a fuse whose rating is higher than necessary ________. A. endangers the apparatus it is supposed to protect B. reduces the possibility of short circuits C. increases the efficiency of the equipment by allowing more current to be used D. wastes money because they are more expensive

Last Answer : Answer: A