Description : Maximum allowable spacing of shear reinforcement for inclined stirrups with an inclination of 45° is restricted to [ A ] 0.75 d [ B ] 0.45 d [ C ] 0.90 d [ D ] d
Last Answer : [ D ] d
Description : According to IS: 456-2000 spacing of vertical stirrups for shear reinforcement has been limited to [ A ] 0.75 d [ B ] 450 mm [ C ] lesser of 0.75 d or 300 mm [ D ] lesser of 0.75d or 450 mm
Last Answer : [ C ] lesser of 0.75 d or 300 mm
Description : The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii
Last Answer : [ D ] i, ii and iii
Description : A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one- ... beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45
Last Answer : Answer: Option C
Description : An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section
Last Answer : Answer: Option D
Description : The centre to centre spacing of vertical stirrups, in a rectangular beam, is (a) Increased towards the centre of the span of the beam (b) Decreased towards the centre of the span of the beam. (c) Increased at the ends. (d) None of these
Last Answer : (a) Increased towards the centre of the span of the beam
Description : According to IS: 456-2000 Maximum spacing of shear reinforcement in no case shall not exceed [ A ] 250 mm [ B ] 300 mm [ C ] 350 mm [ D ] 450 mm
Last Answer : [ B ] 300 mm
Description : The allowable shear stress in stiffened webs of mild steel beams decreases with (a) Decrease in the spacing of the stiffeners (b) Increase in the spacing of the stiffeners (c) Decrease in the effective depth (d) Increase in the effective depth
Last Answer : (b) Increase in the spacing of the stiffeners
Description : An R.C.C beam of 25 cm width has a clear span of 5 metres and carries a U.D.L. of 2000 kg/m inclusive of its self weight. If the lever arm of the section is 45 cm., the beam is ( ... shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined members (D) Needs revision of the section
Last Answer : Answer: Option A
Description : The allowable tensile stress in mild steel stirrups, reinforced cement concrete, is (A) 1400 kg/cm2 (B) 190 kg/cm2 (C) 260 kg/cm2 (D) 230 kg/cm
Description : A circular pipe is subjected to maximum shear force of 60 kN. What is the diameter of the pipe if maximum allowable shear stress is 5 Mpa? a. 27.311 mm b. 75.56 mm c. 142.72 mm d. 692.10 mm
Last Answer : c. 142.72 mm
Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm (C) 150 cm (D) 200 cm
Description : If L is the effective span of a R.C.C. beam which is subjected to maximum shear qmax at the ends, the distance from either end over which stirrups for the shear, are provided, is (A) (L/2) (1 - 3/qmax) (B) (L/3) (1 - 5/qmax) (C) (L/2) (1 - 5/qmax) (D) (L/2) (1 - 2/qmax)
Description : Spacing of stirrups in a rectangular beam, is (A) Kept constant throughout the length (B) Decreased towards the centre of the beam (C) Increased at the ends (D) Increased at the centre of the beam
Description : The torsion resisting capacity of a given reinforced concrete section. (a) Decreases with decrease in stirrups spacing. (b) Decreases with increase in longitudinal bars. (c) Does not depend upon stirrups and longitudinal steels. (d) Increases with increase in stirrups and longitudinal steels.
Last Answer : (d) Increases with increase in stirrups and longitudinal steels.
Description : According to IS:456-1978, the spacing of stirrups shall not exceed a distance ______the leverarm of the resisting moment. (a) Equal to (b) Two times (c) Three times (d) All the above
Last Answer : (a) Equal to
Description : In order to achieve economy, the spacing of stirrups at mid span section---------- compared to that of support section [ A ] May be decreased [ B ] May be increased [ C ] Must be kept equal [ D ] None of the above.
Last Answer : [ B ] May be increased
Description : A stirrups consists of ____________diameter mildsteel bars bent round the tensile reinforcement (a) 1 to 5mm (b) 5 to 12mm (c) 12 to 18mm (d) All the above
Last Answer : (b) 5 to 12mm
Description : The maximum spacing of manholes specified by Indian standard in sewers upto 0.3 m diameter is A. 20 m B. 30 m C. 45 m D. 75 m
Last Answer : ANS: C
Description : The shear reinforcement in R.C.C. is provided to resist (A) Vertical shear (B) Horizontal shear (C) Diagonal compression (D) Diagonal tension
Description : Shear reinforcement is provided in the form of (a) Vertical bars (b) Inclined bars (c) Combination of vertical and inclined bars (d) All the above
Last Answer : (d) All the above
Description : The Maximum spacing of Secondary reinforcement in slabs should be [ A ] Less than 450 mm [ B ] Less than 300 mm [ C ] Smaller of three times the effective depth and 450 mm [ D ] Smaller of five times the effective depth and 450 mm
Last Answer : [ D ] Smaller of five times the effective depth and 450 mm
Description : The Maximum spacing of Main reinforcement „m‟ slabs shall be [ A ] Less than three times of the effective depth [ B ] Less than 300mm [ C ] Smaller of (a) and (b) [ D ] Greater of (a) and (b)
Last Answer : [ C ] Smaller of (a) and (b)
Description : The maximum of spacing of side face reinforcement shall not exceed [ A ] 300 mm [ B ] Web thickness [ C ] Lesser of (a) and (b) [ D ] Greater of (a) and (b)
Last Answer : [ C ] Lesser of (a) and (b)
Description : Maximum allowable shear stress for M25 grade concrete is [ A ] 2.5 N/mm2 [ B ] 2.8 N/mm2 [ C ] 3.1 N/mm2 [ D ] 3.5 N/mm2
Last Answer : [ C ] 3.1 N/mm2
Description : For a balanced section, the tensile stress in the reinforcement [ A ] reaches its allowable stress [ B ] is always less than its allowable stress [ C ] may be greater than its allowable stress [ D ] none of the above
Last Answer : [ A ] reaches its allowable stress
Description : Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of ... (D) The number of longitudinal bars provided in a circular column should not be less than four
Description : In a combined footing if shear stress does not exceed 5 kg/cm2 , the nominal stirrups provided are (A) 6 legged (B) 8 legged (C) 10 legged (D) 12 legged
Last Answer : Answer: Option B
Description : In a combined footing if shear stress exceeds 5 kg/cm2 , the nominal stirrups provided are: (A) 6 legged (B) 8 legged (C) 10 legged (D) 12 legged
Description : In a combined footing, in the zones where the shear stresses are less than 5 kg/cm2 , stirrups to be provided are generally (a) 2 – legged (b) 4-legged (c) 8 – legged (d) 12 legged
Last Answer : (b) 4-legged
Description : According to IS : 456-2000, clause 39.4, stirrups should be provided for a shear of [ A ] at least 75% [ B ] at least 50% [ C ] at least 25 % [ D ] none of the above.
Last Answer : [ B ] at least 50%
Description : All the maximum shear stresses are at an angle of (a)45 0 (b) 90 0 (c) 135 0 (d) None
Last Answer : (b) 90 0
Description : The maximum allowable Los Angeles abrasion value for high quality surface course is (A) 10 % (B) 20 % (C) 30 % (D) 45 %
Description : The angle between a principal plane and a plane of maximum shear is a. 15 0 b. 45 0 c. 75 0 d. None
Last Answer : b. 45 0
Description : If a beam fails in bond, then its bond strength can be increased most economically by (A) Increasing the depth of beam (B) Using thinner bars but more in number (C) Using thicker bars but less in number (D) Providing vertical stirrups
Description : The amount of reinforcement for main bars in a slab, is based upon (A) Minimum bending moment (B) Maximum bending moment (C) Maximum shear force (D) Minimum shear force
Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m
Description : The amount of reinforcement for main bars in a slab, is based upon (a) Maximum bending moment (b) Minimum bending moment (c) Maximum shear force (d) Minimum shear force
Last Answer : (a) Maximum bending moment
Description : High strength of concrete requires a water cement ratio of [ A ] 0.10 to 0.15 [ B ] 0.25 to 0.30 [ C ] 0.45 to 0.60 [ D ] 0.75 to 0.90
Last Answer : [ B ] 0.25 to 0.30
Description : Minimum spacing between horizontal parallel reinforcement of different sizes, should not be less than (A) One diameter of thinner bar (B) One diameter of thicker bar (C) Twice the diameter of thinner bar (D) None of these
Description : The spacing of transverse reinforcement of column is decided by the following consideration. (A) The least lateral dimension of the column (B) Sixteen times the diameter of the smallest longitudinal ... column (C) Forty-eight times the diameter of transverse reinforcement (D) All the above
Description : Minimum spacing between horizontal parallel reinforcement of the same size should not be less than (A) One diameter (B) 2.5 diameters (C) 3 diameters (D) 3.5 diameters
Description : In limit state approach, spacing of main reinforcement controls primarily (a) Cracking (b) Deflection (c ) Durability (d) Collapse
Last Answer : (a) Cracking
Description : The main reinforcement of a R.C. slab consists of 10 mm bars at 100 mm spacing; if it is desired to replace the 10 mm bars by 12 mm bars, then the spacing of 12mm bars should be (a) 120 mm (b) 140 mm (c ) 144 mm (d) 160mm
Last Answer : (c ) 144 mm
Description : In a general two dimensional stress system, planes of maximum shear stress are inclined at ___ with principal planes. a. 90 degree b. 180 degree c. 45 degree d. 60 degree
Last Answer : c. 45 degree
Description : A reinforced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can be used is (a) 6 mm diameter (b) 8 mm diameter (c) 10 mm diameter (d) 12 mm diameter
Last Answer : (b) 8 mm diameter
Description : In moderate exposure , the allowable crack width at the surface of concrete should be [ A ] 0.20 mm [ B ] 0.30 mm [ C ] 0.45 mm [ D ] 0.55 mm
Last Answer : [ A ] 0.20 mm
Description : According to the ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30
Last Answer : a) X=30 Y=18