According to IS:456, the diameter of the helices in circular a column shall be at least [ A ] The diameter of longitudinal steel [ B ] One-half the diameter of longitudinal steel [ C ] One-fourth the diameter of longitudinal steel [ D ] Three-fourth the diameter of longitudinal steel

According to IS:456, the diameter of the helices in circular a column shall be at least
[ A ] The diameter of longitudinal steel
[ B ] One-half the diameter of longitudinal steel
[ C ] One-fourth the diameter of longitudinal steel
[ D ] Three-fourth the diameter of longitudinal steel
by

1 Answer

Answer :

[ C ] One-fourth the diameter of longitudinal steel
by

Related questions

The diameter of the Links in column should be at least……….of the largest diameter of the longitudinal steel [ A ] One-half [ B ] Three-fourth [ C ] One eighth [ D ] One – fourth

Description : The diameter of the Links in column should be at least……….of the largest diameter of the longitudinal steel [ A ] One-half [ B ] Three-fourth [ C ] One eighth [ D ] One – fourth

Last Answer : [ D ] One – fourth

According to IS: 456 -2000, the spacing of links in a Column should be less than [ A ] 16 x diameter of smallest longitudinal bar [ B ] 24 x diameter of smallest longitudinal bar [ C ] 48 x diameter of smallest longitudinal bar [ D ] 48 x diameter of greatest longitudinal bar

Description : According to IS: 456 -2000, the spacing of links in a Column should be less than [ A ] 16 x diameter of smallest longitudinal bar [ B ] 24 x diameter of smallest longitudinal bar [ C ] 48 x diameter of smallest longitudinal bar [ D ] 48 x diameter of greatest longitudinal bar

Last Answer : [ A ] 16 x diameter of smallest longitudinal bar

Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not exceed four [ C ] The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above

Description : Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not ... The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above

Last Answer : [ B ] The number of longitudinal bars in a circular column should not exceed four

According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is (A) Half of the width of the slab (B) Two-third of the width of the slab (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab

Description : According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is ... (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab

Last Answer : Answer: Option C

In any case, the minimum diameter of the link in a column, according to IS:456-2000 is [ A ] 5 mm [ B ] 6 mm [ C ] 8 mm [ D ] 10 mm

Description : In any case, the minimum diameter of the link in a column, according to IS:456-2000 is [ A ] 5 mm [ B ] 6 mm [ C ] 8 mm [ D ] 10 mm

Last Answer : [ B ] 6 mm

Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of column should not exceed 300 mm (C) Reinforcing bars in a column should not be less than 12 mm in diameter (D) The number of longitudinal bars provided in a circular column should not be less than four

Description : Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of ... (D) The number of longitudinal bars provided in a circular column should not be less than four

Last Answer : Answer: Option D

Minimum pitch of transverse reinforcement in a column is (A) The least lateral dimension of the member (B) Sixteen times the smallest diameter of longitudinal reinforcement bar to be tied (C) Forty-eight times the diameter of transverse reinforcement (D) Lesser of the above three values

Description : Minimum pitch of transverse reinforcement in a column is (A) The least lateral dimension of the member (B) Sixteen times the smallest diameter of longitudinal reinforcement bar to be tied (C) Forty-eight times the diameter of transverse reinforcement (D) Lesser of the above three values

Last Answer : Answer: Option D

For a longitudinal reinforcing bar in a column, the minimum cover shall neither be less than the diameter of bar nor less than (A) 15 mm (B) 25 mm (C) 30 mm (D) 40 mm

Description : For a longitudinal reinforcing bar in a column, the minimum cover shall neither be less than the diameter of bar nor less than (A) 15 mm (B) 25 mm (C) 30 mm (D) 40 mm

Last Answer : Answer: Option D

The spacing of transverse reinforcement of column is decided by the following consideration. (A) The least lateral dimension of the column (B) Sixteen times the diameter of the smallest longitudinal reinforcing rods in the column (C) Forty-eight times the diameter of transverse reinforcement (D) All the above

Description : The spacing of transverse reinforcement of column is decided by the following consideration. (A) The least lateral dimension of the column (B) Sixteen times the diameter of the smallest longitudinal ... column (C) Forty-eight times the diameter of transverse reinforcement (D) All the above

Last Answer : Answer: Option D

Minimum cover to longitudinal steel in a column should be (if the diameter of bar, Ø> 12mm) [ A ] 25 mm [ B ] 30 mm [ C ] 40 mm [ D ] 50 mm

Description : Minimum cover to longitudinal steel in a column should be (if the diameter of bar, Ø> 12mm) [ A ] 25 mm [ B ] 30 mm [ C ] 40 mm [ D ] 50 mm

Last Answer : [ C ] 40 mm

According to IS:456-1978, the spacing of stirrups shall not exceed a distance ______the leverarm of the resisting moment. (a) Equal to (b) Two times (c) Three times (d) All the above

Description : According to IS:456-1978, the spacing of stirrups shall not exceed a distance ______the leverarm of the resisting moment. (a) Equal to (b) Two times (c) Three times (d) All the above

Last Answer : (a) Equal to

The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ D ] i, ii and iii

The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ D ] i, ii and iii

The effective width of a column strip of a flat slab, is (A) One-fourth the width of the panel (B) Half the width of the panel (C) Radius of the column (D) Diameter of the column

Description : The effective width of a column strip of a flat slab, is (A) One-fourth the width of the panel (B) Half the width of the panel (C) Radius of the column (D) Diameter of the column

Last Answer : Answer: Option B

According to IS 456, minimum slenderness ratio for a short concrete column is (a) Less than 12 (b) Between 12 and 18 (c) Between 18 and 24 (d) More than 24

Description : According to IS 456, minimum slenderness ratio for a short concrete column is (a) Less than 12 (b) Between 12 and 18 (c) Between 18 and 24 (d) More than 24

Last Answer : (a) Less than 12

According to IS:456-2000, the minimum slenderness ratio for a short column is [ A ] Less than 12 [ B ] Between 12 and 18 [ C ] Less than 18 [ D ] Must be greater than 18

Description : According to IS:456-2000, the minimum slenderness ratio for a short column is [ A ] Less than 12 [ B ] Between 12 and 18 [ C ] Less than 18 [ D ] Must be greater than 18

Last Answer : [ A ] Less than 12

According to IS:456-2000, the minimum eccentricity in no case [ A ] Shall be not less than 20mm [ B ] Shall be not greater than 30mm [ C ] Shall be 20mm-30mm [ D ] None of the above

Description : According to IS:456-2000, the minimum eccentricity in no case [ A ] Shall be not less than 20mm [ B ] Shall be not greater than 30mm [ C ] Shall be 20mm-30mm [ D ] None of the above

Last Answer : [ A ] Shall be not less than 20mm

According to IS: 456-2000 Maximum spacing of shear reinforcement in no case shall not exceed [ A ] 250 mm [ B ] 300 mm [ C ] 350 mm [ D ] 450 mm

Description : According to IS: 456-2000 Maximum spacing of shear reinforcement in no case shall not exceed [ A ] 250 mm [ B ] 300 mm [ C ] 350 mm [ D ] 450 mm

Last Answer : [ B ] 300 mm

The Maximum diameter steel in slabs should not exceed --------- the total thickness of the slab [ A ] One-half [ B ] One-fourth [ C ] One-eighth [ D ] One-sixteenth

Description : The Maximum diameter steel in slabs should not exceed --------- the total thickness of the slab [ A ] One-half [ B ] One-fourth [ C ] One-eighth [ D ] One-sixteenth

Last Answer : [ C ] One-eighth

If the average bending stress is 6 kg/cm2 for M 150 grade concrete, the length of embedment of a bar of diameter d according to I.S. 456 specifications, is (A) 28 d (B) 38 d (C) 48 d (D) 58 d

Description : If the average bending stress is 6 kg/cm2 for M 150 grade concrete, the length of embedment of a bar of diameter d according to I.S. 456 specifications, is (A) 28 d (B) 38 d (C) 48 d (D) 58 d

Last Answer : Answer: Option D

The diameter of the stirrups according to IS : 456-2000 should not be less than [ A ] 5 mm [ B ] 6 mm [ C ] 8 mm [ D ] 10 mm

Description : The diameter of the stirrups according to IS : 456-2000 should not be less than [ A ] 5 mm [ B ] 6 mm [ C ] 8 mm [ D ] 10 mm

Last Answer : [ B ] 6 mm

If a circular beam of diameter d experiences a longitudinal strain P/E and a lateral strain 2P/mE, the volumetric strain is (A) (P/E) + (2P/mE) (B) (P/E) - (2P/mE) (C) (P/E) + (mE/2P) (D) (P/E) - (mE/2P)

Description : If a circular beam of diameter d experiences a longitudinal strain P/E and a lateral strain 2P/mE, the volumetric strain is (A) (P/E) + (2P/mE) (B) (P/E) - (2P/mE) (C) (P/E) + (mE/2P) (D) (P/E) - (mE/2P)

Last Answer : (B) (P/E) - (2P/mE)

The diameter of longitudinal bars of a column should never be less than (A) 6 mm (B) 8 mm (C) 10 mm (D) 12 mm

Description : The diameter of longitudinal bars of a column should never be less than (A) 6 mm (B) 8 mm (C) 10 mm (D) 12 mm

Last Answer : Answer: Option D

If the diameter of longitudinal bars of a square column is 16 mm, the diameter of lateral ties should not be less than (A) 4 mm (B) 5 mm (C) 6 mm (D) 8 mm

Description : If the diameter of longitudinal bars of a square column is 16 mm, the diameter of lateral ties should not be less than (A) 4 mm (B) 5 mm (C) 6 mm (D) 8 mm

Last Answer : Answer: Option B

The minimum diameter of longitudinal bars in a column is (A) 6 mm (B) 8 mm (C) 12 mm (D) 16 mm

Description : The minimum diameter of longitudinal bars in a column is (A) 6 mm (B) 8 mm (C) 12 mm (D) 16 mm

Last Answer : Answer: Option C

According to IS : 456-2000, clause 39.4, stirrups should be provided for a shear of [ A ] at least 75% [ B ] at least 50% [ C ] at least 25 % [ D ] none of the above.

Description : According to IS : 456-2000, clause 39.4, stirrups should be provided for a shear of [ A ] at least 75% [ B ] at least 50% [ C ] at least 25 % [ D ] none of the above.

Last Answer : [ B ] at least 50%

According to IS:456-2000, Limiting value of yield strain for Fe250grade steel is [ A ] 0.031 [ B ] 0.0031 [ C ] 0.038 [ D ] 0.0038

Description : According to IS:456-2000, Limiting value of yield strain for Fe250grade steel is [ A ] 0.031 [ B ] 0.0031 [ C ] 0.038 [ D ] 0.0038

Last Answer : [ B ] 0.0031

According to IS: 456-2000, limiting value of yield strain for Fe415 grade steel is [ A ] 0.031 [ B ] 0.0031 [ C ] 0.038 [ D ] 0.0038

Description : According to IS: 456-2000, limiting value of yield strain for Fe415 grade steel is [ A ] 0.031 [ B ] 0.0031 [ C ] 0.038 [ D ] 0.0038

Last Answer : [ D ] 0.0038

According to IS:456-2000, Limiting value of yield strain for Fe250 grade steel is [ A ] 0.031 [ B ] 0.0031 [ C ] 0.038 [ D ] 0.0038

Description : According to IS:456-2000, Limiting value of yield strain for Fe250 grade steel is [ A ] 0.031 [ B ] 0.0031 [ C ] 0.038 [ D ] 0.0038

Last Answer : [ B ] 0.0031

According to IS: 456-2000, limiting value of yield strain for Fe415 grade steel is [ A ] 0.031 [ B ] 0.0031 [ C ] 0.038 [ D ] 0.0038

Description : According to IS: 456-2000, limiting value of yield strain for Fe415 grade steel is [ A ] 0.031 [ B ] 0.0031 [ C ] 0.038 [ D ] 0.0038

Last Answer : [ D ] 0.0038

If Ac , Asc and A are areas of concrete, longitudinal steel and section of a R.C.C. column and m and c are the modular ratio and maximum stress in the configuration of concrete, the strength of column is (A) cAc + m cAsc (B) c (A - Asc) + m cAsc (C) c [A + (m - 1)ASC] (D) All the above

Description : If Ac , Asc and A are areas of concrete, longitudinal steel and section of a R.C.C. column and m and c are the modular ratio and maximum stress in the configuration of concrete, the strength of column is (A) cAc + m cAsc (B) c (A - Asc) + m cAsc (C) c [A + (m - 1)ASC] (D) All the above

Last Answer : Answer: Option D

Maximum percentage of longitudinal steel in a column should be less than [ A ] 6% [ B ] 8% [ C ] 9% [ D ] 10%

Description : Maximum percentage of longitudinal steel in a column should be less than [ A ] 6% [ B ] 8% [ C ] 9% [ D ] 10%

Last Answer : [ B ] 8%

Minimum percentage of longitudinal steel in a column should not be less than [ A ] 0.60% [ B ] 0.80% [ C ] 1.00% [ D ] 1.20%

Description : Minimum percentage of longitudinal steel in a column should not be less than [ A ] 0.60% [ B ] 0.80% [ C ] 1.00% [ D ] 1.20%

Last Answer : [ B ] 0.80%

The loose pockets in soil mass can be bridged safely by providing a raft foundation provided the soft area is smaller than (A) The column spacing (B) One-third the column spacing (C) Half the column spacing (D) Three-fourth the column spacing

Description : The loose pockets in soil mass can be bridged safely by providing a raft foundation provided the soft area is smaller than (A) The column spacing (B) One-third the column spacing (C) Half the column spacing (D) Three-fourth the column spacing

Last Answer : Answer: Option B

The minimum diameter of longitudinal steel should be [ A ] 10 mm [ B ] 12 mm [ C ] 16 mm [ D ] 20 mm

Description : The minimum diameter of longitudinal steel should be [ A ] 10 mm [ B ] 12 mm [ C ] 16 mm [ D ] 20 mm

Last Answer : [ B ] 12 mm

The diameter of ties in a column should be (A) More than or equal to one fourth of diameter of main bar (B) More than or equal to 5 mm (C) More than 5 mm but less than one-fourth of diameter of main bar (D) More than 5 mm and also more than one-fourth of diameter of main bar

Description : The diameter of ties in a column should be (A) More than or equal to one fourth of diameter of main bar (B) More than or equal to 5 mm (C) More than 5 mm but less than one-fourth of diameter of main bar (D) More than 5 mm and also more than one-fourth of diameter of main bar

Last Answer : Answer: Option D

The discharge through a convergent mouthpiece is __________ the discharge through an internal mouthpiece of the same diameter and head of water. (A) Equal to (B) One-half (C) Three fourth (D) Double

Description : The discharge through a convergent mouthpiece is __________ the discharge through an internal mouthpiece of the same diameter and head of water. (A) Equal to (B) One-half (C) Three fourth (D) Double

Last Answer : Answer: Option D

The eccentricity (e) of a hollow circular column, external diameter 25 cm, internal diameter 15 cm for an eccentric load 100 t for non-development of tension, is (A) 2.75 cm (B) 3.00 cm (C) 3.50 cm (D) 4.25 cm

Description : The eccentricity (e) of a hollow circular column, external diameter 25 cm, internal diameter 15 cm  for an eccentric load 100 t for non-development of tension, is  (A) 2.75 cm  (B) 3.00 cm  (C) 3.50 cm  (D) 4.25 cm

Last Answer : (D) 4.25 cm

The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose ends are hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2 , the permissible maximum crippling load will be (A) 1.288 tonnes (B) 12.88 (C) 128.8 tonnes (D) 288.0

Description : The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose ends are hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2 , the permissible maximum crippling load will be (A) 1.288 tonnes (B) 12.88 (C) 128.8 tonnes (D) 288.0

Last Answer : (B) 12.88

For keeping the stress wholly compressive the load may be applied on a circular column anywhere within a concentric circle of diameter (A) d/2 (B) d/3 (C) d/4 (D) d/8

Description : For keeping the stress wholly compressive the load may be applied on a circular column anywhere within a concentric circle of diameter (A) d/2 (B) d/3 (C) d/4 (D) d/8

Last Answer : (C) d/4

A student measured the diameter of a small steel ball using a screw gauge of least count 0.001 cm. The main scale reading is 5 mm and zero of circular

Description : A student measured the diameter of a small steel ball using a screw gauge of least count 0.001 cm. The main scale reading is 5 mm and zero of circular

Last Answer : A student measured the diameter of a small steel ball using a screw gauge of least count 0.001 cm. The main scale ... (C) 0.053 cm (D) 0.529 cm

To ascertain the maximum permissible eccentricity of loads on circular columns, the rule generally followed, is (A) Middle half rule of columns (B) Middle third rule of columns (C) Middle fourth rule of columns (D) None of these

Description : To ascertain the maximum permissible eccentricity of loads on circular columns, the rule generally followed, is (A) Middle half rule of columns (B) Middle third rule of columns (C) Middle fourth rule of columns (D) None of these

Last Answer : (C) Middle fourth rule of columns

The range within which a load can be applied on a rectangular column, to avoid any tensile stress, is (A) One-half of the base (B) One-fifth of the base (C) One-fourth of the base (D) One-fifth of the base

Description : The range within which a load can be applied on a rectangular column, to avoid any tensile stress,  is  (A) One-half of the base  (B) One-fifth of the base  (C) One-fourth of the base  (D) One-fifth of the base 

Last Answer : (B) One-fifth of the base 

Top bars are extended to the projecting parts of the combined footing of two columns Ldistance apart for a distance of (A) 0.1 L from the outer edge of column (B) 0.1 L from the centre edge of column (C) Half the distance of projection (D) One-fourth the distance of projection

Description : Top bars are extended to the projecting parts of the combined footing of two columns Ldistance apart for a distance of (A) 0.1 L from the outer edge of column (B) 0.1 L from the centre edge of column (C) Half the distance of projection (D) One-fourth the distance of projection

Last Answer : Answer: Option B

As per IS : 456, the reinforcement in a column should not be less than (A) 0.5% and not more than 5% of cross-sectional area (B) 0.6% and not more than 6% of cross-sectional area (C) 0.7% and not more than 7% of cross-sectional area (D) 0.8% and not more than 8% of cross-sectional area

Description : As per IS : 456, the reinforcement in a column should not be less than (A) 0.5% and not more than 5% of cross-sectional area (B) 0.6% and not more than 6% of cross-sectional area (C) 0.7% and not more than 7% of cross-sectional area (D) 0.8% and not more than 8% of cross-sectional area

Last Answer : Answer: Option D

As per I.S. 456 - 1978, the pH value of water shall be (A) Less than 6 (B) Equal to 6 (C) Not less than 6 (D) Equal to 7

Description : As per I.S. 456 - 1978, the pH value of water shall be (A) Less than 6 (B) Equal to 6 (C) Not less than 6 (D) Equal to 7

Last Answer : Answer: Option C

The diameter of transverse reinforcement of columns should be equal to one-fourth of the diameter of the main steel rods but not less than (A) 4 mm (B) 5 mm (C) 6 mm (D) 7 mm

Description : The diameter of transverse reinforcement of columns should be equal to one-fourth of the diameter of the main steel rods but not less than (A) 4 mm (B) 5 mm (C) 6 mm (D) 7 mm

Last Answer : Answer: Option D

The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, is (A) One-half of the radius (B) One-third of the radius (C) One-quarter of the radius (D) One-fifth of the radius

Description : The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, ... One-third of the radius (C) One-quarter of the radius (D) One-fifth of the radius

Last Answer : (C) One-quarter of the radius

In a short cylindrical external mouthpiece, the vena contracta occurs at a distance __________ the diameter of the orifice from the outlet of orifice. (A) Equal to (B) One-fourth (C) One-third (D) One-half

Description : In a short cylindrical external mouthpiece, the vena contracta occurs at a distance __________ the diameter of the orifice from the outlet of orifice. (A) Equal to (B) One-fourth (C) One-third (D) One-half

Last Answer : Answer: Option B

The breadth of rib in a T-beam should at least be equal to __________the depth of rib (a) One –half (b) One –third (c) One-fourth (d) One –sixth

Description : The breadth of rib in a T-beam should at least be equal to __________the depth of rib (a) One –half (b) One –third (c) One-fourth (d) One –sixth

Last Answer : (b) One –third