Conversion of dynamic velocity head into static pressure head in a centrifugal pump is the result of :
 (a) Increasing area of flow between adjacent vanes from inlet to outlet
 (b) Difference in pressure between suction and delivery ends
 (c) Radial thrust in pumps
 (d) Stuffing Box

1 Answer

Answer :

(b) Difference in pressure between suction and delivery ends

Related questions

Description : In centrifugal pump installation,  (A) Pump is properly primed before starting  (B) The diameter of the pipe at inlet as well as at outlet, is kept smaller than the delivery pipe  (C) The ... out if it is started with empty delivery pipe and with open gate valve  (D) All the above 

Last Answer : (D) All the above 

Description : Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes ... or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Last Answer : (C) Mounting of two or more impellers in series on a single shaft

Description : For attaining maximum efficiency, a Francis turbine runner is so designed as to result in radial discharge at exit. This is done by : a) Providing runner vane angle at inlet as 90o b) Providing ... 90o d) Designing for absolute velocity at outlet to be inclined at 90o to direction of vane there

Last Answer : d) Designing for absolute velocity at outlet to be inclined at 90o to direction of vane there

Description : Pick up the correct statement from the following regarding radial flow centrifugal pumps:  (A) These are provided with volute type or turbine type casings  (B) In involute type of radial flow ... centrifugal pump, is always higher than that of  volute type  (D) All the above 

Last Answer : (D) All the above 

Description : The head developed by a centrifugal pump is largely determined by the (A) Power of the pump (B) Nature of the liquid being pumped (C) Angle of the vanes and the speed of the tip of the impeller (D) Vapour pressure of the liquid

Last Answer : (C) Angle of the vanes and the speed of the tip of the impeller

Description : Cavitation in a centrifugal pump can be avoided by keeping the (A) Inlet pressure high (B) Outlet pressure low (C) Inlet pressure low (D) Outlet pressure high

Last Answer : (A) Inlet pressure high

Description : A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Last Answer : (A) Employs such an impeller, through which the flow is a combination of radial & axial flow

Description : The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor ... of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Last Answer : (C) Suction minus vapor pressure of the liquid at suction temperature

Description : The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor ... of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Last Answer : (C) Suction minus vapor pressure of the liquid at suction temperature

Description : Specific speed of a centrifugal pump depends upon the __________ head. (A) Suction (B) Delivery (C) Manometric (D) None of these

Last Answer : (D) None of these

Description : In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) ... level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Last Answer : (B) Water flow in the suction and discharge pipe of a reciprocating pump

Description : Which one of the following types of impeller vanes are most commonly used in centrifugal type compressors? A. Forward curved B. Radial C. Backward curved D. Tangential

Last Answer : ANSWER : C

Description : What causes cavitation in centrifugal pump? (A) High suction pressure (B) Low barometric pressure (C) Low suction pressure (D) High suction velocity

Last Answer : (C) Low suction pressure

Description : Liquid delivery by centrifugal pump starts, only when the head developed by it is equal to the __________ head. (A) Manometric (B) Total (C) Static (D) Friction

Last Answer : (A) Manometric

Description : Net positive suction head (NPSH) of a centrifugal pump must be (A) Greater than the vapour pressure of the liquid (B) Less than the vapour pressure of the liquid (C) Equal to the vapour pressure of the liquid (D) Less than barometric pressure

Last Answer : (A) Greater than the vapour pressure of the liquid

Description : Cavitation occurs in a centrifugal pump when the suction pressure is (A) Less than the vapour pressure of the liquid at that temperature (B) Greater than the vapour pressure of the liquid at that temperature (C) Equal to the vapour pressure (D) Equal to the developed head

Last Answer : (A) Less than the vapour pressure of the liquid at that temperature

Description : What is a stuffing box in a centrifugal pump?

Last Answer : A stuffing box or gland package is an assembly which is used to house a gland seal. It is used to prevent leakage of fluid, such as water or steam, between sliding or turning parts ... elements. Building Electronic Controls, Inc. provides top quality and the best fire alarm services in California.

Description : The variable required to be known in correlations used for estimating the horse power of a centrifugal gas compressor and hence its cost is P. Inlet pressure Q. Compressor rpm R. Delivery pressure S. Volumetric flow rate at inlet. (A) P, Q and R (B) P and R (C) R and S (D) P, Rand S

Last Answer : (A) P, Q and R

Description : Most commonly used pump for lifting water in water supply mains, is  (A) Axial flow pump  (B) Reciprocating pump  (C) Rotary type pump  (D) Centrifugal pumps 

Last Answer : (A) Axial flow pump 

Description : Consider the following statements: The total head against which a pump has to work must include, besides any other items, 1. the suction lift. 2. the delivery head. 3. the head lost due to friction at entrance in the rising main. 4. the ... 2 & 3 only (b) 2 & 3 only (c) 1, 2, 3 & 4 (d) 3 & 4 only

Last Answer : (c) 1, 2, 3 & 4

Description : Volute of a centrifugal pump should be designed in a fashion, such that the (A) Kinetic head gets converted into static head (B) Moving stream gradually reduces velocity (C) Mean velocity remains constant (D) None of these

Last Answer : (A) Kinetic head gets converted into static head

Description : The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Description : 24 pumps are connected to a tank. Some of them are inlet pumps and the others are outlet pumps. Each of the inlet pumps an fill the tank in 16hours and each of the outlet pumps can empty the tank completely in ... gets filled in 48 hours. How many inlet pumps are there? A) 16 B) 18 C) 17 D) 14

Last Answer : D (x/16)-[(24-x)/12] = 1/48 x/16-24/48+x/12=1/48 (3+4)x/48=97/48 7x/48=97/48 7x=97 X=14

Description : Which of the following is not the function of a volute casing provided in a centrifugal pump? (A) To reduce the head loss in discharge (B) To increase the pump efficiency (C) To collect liquid ... and to transmit it to the delivery pipe at constant velocity (D) To increase the pump discharge rate

Last Answer : Option D

Description : The peripheral velocity at inlet of a centrifugal pump having inlet diameter of 25 cms and rotating at 950 rpm is __________ m/sec. (A) 1.8 (B) 12.4 (C) 186.2 (D) 736.4

Last Answer : (B) 12.4

Description : Hydraulic intensifier is used for increasing the (A) Rate of velocity of liquid supply (B) Rate of flow through delivery pipeline of a pump (C) Intensity of pressure of the liquid (D) Momentum rate through delivery pipe

Last Answer : (C) Intensity of pressure of the liquid

Description : Design of the casing of centrifugal pump should be such as to minimise the (A) Back flow through impeller (B) Loss of kinetic head (C) Loss of static head (D) None of these

Last Answer : (B) Loss of kinetic head

Description : The excess of the sum of pressure & velocity heads over the vaporpressure of the liquid at the suction is called the (A) Static submergence (B) Net positive suction head (NPSH) (C) Cavitation sensitivity (D) Priming

Last Answer : (B) Net positive suction head (NPSH)

Description : The blades of a centrifugal impeller are said to be curved forward, if the __________ of the motion of impeller blades. (A) Inlet tip of a blade curves in a direction opposite to that (B) Outlet tip ... Inlet tip of a blade is towards the direction (D) Outlet tip of a blade is towards the direction

Last Answer : (D) Outlet tip of a blade is towards the direction

Description : Acceleration head in a reciprocating pump (A) Increases the work done during delivery stroke (B) Decreases the work done during suction stroke (C) Does not change the work requirement of the pump (D) Increases the work done during suction stroke

Last Answer : (C) Does not change the work requirement of the pump

Description : In centrifugal pump operation, the cavitation can be eliminated by maintaining suction pressure __________ the vapor pressure of the liquid at the suction temperature. (A) Lower than (B) Higher than (C) Equal to (D) None of these

Last Answer : (B) Higher than

Description : Reciprocating pumps compared to centrifugal pumps (A) Deliver liquid at uniform pressure (B) Can handle slurries more efficiently (C) Are not subject to air binding (D) Can be operated with delivery valve closed

Last Answer : (C) Are not subject to air binding

Description : State the difference between Static head & Manometric head in centrifugal pump.

Last Answer : Static head: The sum of suction head & delivery head is known as static head.  Manometric head: It is the total head that pump is required to develop. This include all losses. This is equal to difference between pressure head at inlet & outlet of pump.

Description : Suction lift of a pump depends upon  (A) Atmospheric pressure  (B) Water temperature  (C) Velocity of water in suction pipe  (D) All the above 

Last Answer : (D) All the above 

Description : Higher specific speed (200-500) of a centrifugal pump indicates that the pump is of __________ flow type. (A) Axial (B) Radial (C) Mixed (D) None of these

Last Answer : (A) Axial

Description : Consider the following statements: Air vessels are fitted on the suction and delivery sides of a reciprocating pump to 1. Achieve higher speed without separation. 2. Reduce work in overcoming frictional resistance. 3. Avoid excessive vibration ... 2 & 3 only (c) 2, 3 & 4 only (d) 1, 2, 3 & 4

Last Answer : (d) 1, 2, 3 & 4

Description : To avoid an interruption in the flow of a siphon, an air vessel is provided (A) At the inlet (B) At the outlet (C) At the summit (D) At any point between inlet and outle

Last Answer : Answer: Option C

Description : Momentum correction factor used in fluid flow problems accounts for the (A) Change in direction of flow (B) Change in total energy (C) Change in pressure (D) Non uniform direction of velocities at inlet & outlet sections

Last Answer : (D) Non uniform direction of velocities at inlet & outlet sections

Description : In the expression of dynamic load capacity P=XVF r + YF a , Y stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor

Last Answer : (c) Thrust load factor

Description : In the expression of dynamic load capacity P=XVF r + YF a , X stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor

Last Answer : (b) Radial load factor

Description : In the expression of dynamic load capacity P=XVF r + YF a , V stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor

Last Answer : (a) Race rotation factor

Description : In the expression of dynamic load capacity P=XVF(r) + YF(a), V stands for ? a) Race rotation factor b) Radial factor c) Thrust factor d) None of the listed

Last Answer : a) Race rotation factor

Description : Volute type of casing is provided in a centrifugal pump to (A) Convert velocity head to pressure head (B) Convert pressure head to velocity head (C) Reduce the discharge fluctuation (D) Increase the discharge

Last Answer : (D) Increase the discharge

Description : Good design of the casing of a centrifugal pump aims at minimising the (A) Cavitation (B) Frictional losses (C) Kinetic energy loss (D) Static head

Last Answer : Option C

Description : A centrifugal pump loses prime after starting. The reason of this trouble may be (A) Incomplete priming (B) Too high a suction lift (C) Low available NPSH and air leaks in the suction pipe (D) All (A), (B), and (C)

Last Answer : (D) All (A), (B), and (C)

Description : Maximum theoretical suction lift for water at 15°C by a centrifugal pump is 34 ft. The same for water at 90°C will be __________ ft. (A) 40 (B) 34 (C) 8 (D) 37

Last Answer : (C) 8

Description : If the discharge of a centrifugal pump is throttled, then its suction lift (A) Increases (B) Decreases (C) Remains unchanged (D) Data insufficient to predict

Last Answer : (A) Increases

Description : Foot valves are provided in the suction line of a centrifugal pump to (A) Avoid priming, every time we start the pump (B) Remove the contaminant present in the liquid (C) Minimise the fluctuation in discharge (D) Control the liquid discharge

Last Answer : (A) Avoid priming, every time we start the pump

Description : The main drawback of centrifugal pump is a)necessity of priming b) discharge from pump varies with the load of water c) For high heads efficiency is low up to 50% d) the suction lift is limited to 6 metre e) all of the above*

Last Answer : e) all of the above*

Description : What type of pump may be appropriate for a liquid near saturation, a low flow rate, and very limited NPSHa (net positive suction head available)?

Last Answer : This application is nearly perfect for a turbine regenerative type of pump. Factors that immediately identify your application and pump type are the small flowrate, low NPSHa, and high temperature. The ... in pressure. You can visit the site below to learn more about these types of pumps.