If water table is encountered in the standard pit while conducting plate load test (a) The load test should be abandoned (b) The pit is considered unsafe (c) Test should be conducted with complete dewatering continuously throughout the test duration (d) The bearing capacity of soil cannot be determined in this condition

If water table is encountered in the standard pit while conducting plate load test
(a) The load test should be abandoned
(b) The pit is considered unsafe
(c) Test should be conducted with complete dewatering continuously throughout the test duration
(d) The bearing capacity of soil cannot be determined in this condition
by

1 Answer

Answer :

(c) Test should be conducted with complete dewatering continuously throughout the test duration
by

Related questions

For determining the ultimate bearing capacity of soil, the recommended size of a square bearing plate to be used in load plate test should be 30 to 75 cm square with a minimum thickness of (A) 5 mm (B) 10 mm (C) 15 mm (D) 25 mm

Description : For determining the ultimate bearing capacity of soil, the recommended size of a square bearing plate to be used in load plate test should be 30 to 75 cm square with a minimum thickness of (A) 5 mm (B) 10 mm (C) 15 mm (D) 25 mm

Last Answer : Answer: Option D

Explain plate load test with neat sketch to determine bearing capacity of soil.

Description : Explain plate load test with neat sketch to determine bearing capacity of soil.

Last Answer : Procedure of plate load test: 1. Excavate a pit of depth equal to 5 times to that of breath of proposed footing. 2. Keep the suitable bearing plate of specified size (30, 45, 60, 75cm square in plan) ... as shown in figure below to find out load before failure as bearing capacity of soil.

In the plate loading test for determining the bearing capacity of soil, the size of square bearing plate should be (A) Less than 300 mm (B) Between 300 mm and 750 mm (C) Between 750 mm and 1 m (D) Greater than 1 m

Description : In the plate loading test for determining the bearing capacity of soil, the size of square bearing plate should be (A) Less than 300 mm (B) Between 300 mm and 750 mm (C) Between 750 mm and 1 m (D) Greater than 1 m

Last Answer : (B) Between 300 mm and 750 mm

A 300 mm square bearing plate settles by 15 mm in a plate load test on a cohesive soil when the intensity of loading is 0.2 N/mm². The settlement of a prototype shallow footing 1 m square under the same intensity of loading is (A) 15 mm (B) 30 mm (C) 50 mm (D) 167 mm

Description : A 300 mm square bearing plate settles by 15 mm in a plate load test on a cohesive soil when the intensity of loading is 0.2 N/mm². The settlement of a prototype shallow footing 1 m square under the same intensity of loading is (A) 15 mm (B) 30 mm (C) 50 mm (D) 167 mm

Last Answer : (C) 50 mm

A 600 mm square bearing plate settles by 15 mm in plate load test on a cohesion-less soil under an intensity of loading of 0.2 N/ram². The settlement of a prototype shallow footing 1 m square under the same intensity of loading is (A) 15 mm (B) Between 15 mm and 25 mm (C) 25 mm (D) Greater than 25 mm

Description : A 600 mm square bearing plate settles by 15 mm in plate load test on a cohesion-less soil under an intensity of loading of 0.2 N/ram². The settlement of a prototype shallow footing 1 m square under the same intensity of ... (A) 15 mm (B) Between 15 mm and 25 mm (C) 25 mm (D) Greater than 25 mm

Last Answer : Answer: Option B

The bearing capacity of piles is determined by (A) Dynamic formula (B) Static formula (C) Pile load tests (D) All the above

Description : The bearing capacity of piles is determined by (A) Dynamic formula (B) Static formula (C) Pile load tests (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement applicable to plate load test (A) Width of the test pit for plate load test is made five times the width of the plate (B) At the centre of the test pit, a hole is dug out whose size is kept equal to the size of the test plate (C) Bottom level of the hole dug at the centre of the test pit, is kept at the level of the actual formation (D) All the above

Description : Pick up the correct statement applicable to plate load test (A) Width of the test pit for plate load test is made five times the width of the plate (B) At the centre of the test pit, a hole is dug ... at the centre of the test pit, is kept at the level of the actual formation (D) All the above

Last Answer : Answer: Option D

Draw a neat labelled sketch of plate load test set up for determination of field bearing capacity.

Description : Draw a neat labelled sketch of plate load test set up for determination of field bearing capacity.

Last Answer : Figure: Plate Load Test using Reaction Truss Loading OR

Consider the following statements: 1. The benefit of surcharge and depth of foundation is only marginal in case of footings on purely cohesive soils. 2. The bearing capacity of a footing in pure clay increases with increase in size of the footing. 3. Size effects in plate load tests are more important in case of cohesionless soils. Which of these statements are correct? (a) 1, 2 & 3 (b) 1 & 2 only (c) 2 & 3 only (d) 1 & 3 only

Description : Consider the following statements: 1. The benefit of surcharge and depth of foundation is only marginal in case of footings on purely cohesive soils. 2. The bearing capacity of a footing in pure clay increases with increase in size of the ... , 2 & 3 (b) 1 & 2 only (c) 2 & 3 only (d) 1 & 3 only

Last Answer : (d) 1 & 3 only

Pick out the wrong statement. (A) In a batch reactor, which is exclusively used for liquid phase reactions; temperature pressure and composition may vary with time (B) In a semi-batch reactor, one reactant is charged batch wise, while the other reactant is fed continuously (C) In a continuous flow reactor, uniform concentration cannot be maintained throughout the vessel even in a well agitated system (D) In a continuous flow reactor, both the reactants and the products flow out continuously

Description : Pick out the wrong statement. (A) In a batch reactor, which is exclusively used for liquid phase reactions; temperature pressure and composition may vary with time (B) In a semi-batch reactor, ... system (D) In a continuous flow reactor, both the reactants and the products flow out continuously

Last Answer : (C) In a continuous flow reactor, uniform concentration cannot be maintained throughout the vessel even in a well agitated system

When a cohesionless soil attains quick condition, it looses (A) Shear strength (B) Bearing capacity (C) Both (a) and (b) (D) Neither (a) nor (6

Description : When a cohesionless soil attains quick condition, it looses (A) Shear strength (B) Bearing capacity (C) Both (a) and (b) (D) Neither (a) nor (6

Last Answer : Answer: Option C

The direct shear test suffers from the following disadvantage: (A) Drain condition cannot be controlled (B) Pore water pressure cannot be measured (C) Shear stress on the failure plane is not uniform (D) The area under the shear and vertical loads does not remain constant throughout the test

Description : The direct shear test suffers from the following disadvantage: (A) Drain condition cannot be controlled (B) Pore water pressure cannot be measured (C) Shear stress on the failure plane is not uniform (D) The area under the shear and vertical loads does not remain constant throughout the test

Last Answer : Answer: Option C

The rise of water table below the foundation influences the bearing capacity of soil mainly by reducing (A) Cohesion and effective angle of shearing resistance (B) Cohesion and effective unit weight of soil (C) Effective unit weight of soil and effective angle of shearing resistance (D) Effective angle of shearing resistance

Description : The rise of water table below the foundation influences the bearing capacity of soil mainly by reducing (A) Cohesion and effective angle of shearing resistance (B) Cohesion and effective ... weight of soil and effective angle of shearing resistance (D) Effective angle of shearing resistance

Last Answer : Answer: Option B

Bearing capacity of soils cannot be improved by (A) Draining sub-soil water (B) Ramming crushed stone in soil (C) Driving sand piles (D) Watering surface of soil

Description : Bearing capacity of soils cannot be improved by (A) Draining sub-soil water (B) Ramming crushed stone in soil (C) Driving sand piles (D) Watering surface of soil

Last Answer : Answer: Option D

Select the incorrect statement. (A) Bearing capacity of a soil depends upon the amount and direction of load (B) Bearing capacity of a soil depends on the type of soil (C) Bearing capacity of a soil depends upon shape and size of footing (D) Bearing capacity of a soil is independent of rate of loading

Description : Select the incorrect statement. (A) Bearing capacity of a soil depends upon the amount and direction of load (B) Bearing capacity of a soil depends on the type of soil (C) Bearing capacity of a ... upon shape and size of footing (D) Bearing capacity of a soil is independent of rate of loading

Last Answer : Answer: Option A

The ultimate bearing capacity of a soil, is (A) Total load on the bearing area (B) Safe load on the bearing area (C) Load at which soil fails (D) Load at which soil consolidates

Description : The ultimate bearing capacity of a soil, is (A) Total load on the bearing area (B) Safe load on the bearing area (C) Load at which soil fails (D) Load at which soil consolidates

Last Answer : Answer: Option C

For a wall carrying heavy load on low bearing capacity soil, (A) Lean concrete bed is provided (B) Thick concrete bed is provided (C) Reinforced concrete bed is provided (D) Both (a) and (c) of the above

Description : For a wall carrying heavy load on low bearing capacity soil, (A) Lean concrete bed is provided (B) Thick concrete bed is provided (C) Reinforced concrete bed is provided (D) Both (a) and (c) of the above

Last Answer : Answer: Option D

The base of a column is subjected to moment. If the intensity of bearing pressure due to axial load is equal to stress due to moment, then the bearing pressure between the base and the concrete is (a) Uniform compression throughout (b) Zero at one end and compression at the other end (c) Tension at one end and compression at the other end (d) Compression, verying as a parabolic profile

Description : The base of a column is subjected to moment. If the intensity of bearing pressure due to axial load is equal to stress due to moment, then the bearing pressure between the base and the concrete ... Tension at one end and compression at the other end (d) Compression, verying as a parabolic profile

Last Answer : (b) Zero at one end and compression at the other end

The single stage well point system of dewatering an excavation can be used if the depth of excavation does not exceed (A) 5 m (B) 10 m (C) 15 m (D) 20 m

Description : The single stage well point system of dewatering an excavation can be used if the depth of excavation does not exceed (A) 5 m (B) 10 m (C) 15 m (D) 20 m

Last Answer : Answer: Option A

Explain the effect of water table on bearing capacity of soil.

Description : Explain the effect of water table on bearing capacity of soil.

Last Answer : Effect of water table on bearing capacity of soil: i. The rise in water table from below the foundation results in decrease in granular soil. ii. When the water table reaches the ... for bearing capacity calculations. ix. As ground water table rises accordingly bearing capacity of soil decreases.

The observed N- value from a standard penetration test conducted in saturated sandy strata is 30; the N- value corrected for dilatancy may be taken as : (b) 15 (a) 20 (c) 23 (d) 39

Description : The observed N- value from a standard penetration test conducted in saturated sandy strata is 30; the N- value corrected for dilatancy may be taken as : (b) 15 (a) 20 (c) 23 (d) 39

Last Answer : (c) 23

Rise of water table in cohesion-less soils upto ground surface reduces the net ultimate bearing capacity approximately by (A) 25 % (B) 50 % (C) 75 % (D) 90 %

Description : Rise of water table in cohesion-less soils upto ground surface reduces the net ultimate bearing capacity approximately by (A) 25 % (B) 50 % (C) 75 % (D) 90 %

Last Answer : (B) 50 %

Suggest the energy conservation techniques in following cases : (i) Motor is running with 70% loaded condition. (ii) Motor is continuously loaded at 50%. (iii) Motor runs with 30% loaded condition but sometimes rises to 50% loading condition. (iv) Motor runs continuously under no-load condition.

Description : Suggest the energy conservation techniques in following cases : (i) Motor is running with 70% loaded condition. (ii) Motor is continuously loaded at 50%. (iii) Motor runs with 30% loaded condition but sometimes rises to 50% loading condition. (iv) Motor runs continuously under no-load condition.

Last Answer : Following are the suggestion the energy conservation techniques in following cases :  (i) Motor is running with 70% loaded condition: Use APFC or IPFC for better power factor improvement. Use ... If possible use low capacity motor for above condition. If possible switch off the motor.

Pick out the wrong statement. (A) Different solids have different equilibrium moisture curves (B) Total condenser or reboiler is considered equivalent to one theoretical plate in McCabe-Thiele method of theoretical plate calculation for distillation column (C) Heat removal load on cooler remains constant, even with increase of the reflux ratio in a distillation column (D) Even a forced draft cooling tower cannot cool water below the wet bulb temperature

Description : Pick out the wrong statement. (A) Different solids have different equilibrium moisture curves (B) Total condenser or reboiler is considered equivalent to one theoretical plate in McCabe-Thiele method of ... (D) Even a forced draft cooling tower cannot cool water below the wet bulb temperature

Last Answer : (C) Heat removal load on cooler remains constant, even with increase of the reflux ratio in a distillation column

The maximum load carried by a pile, when it continues to sink without further increase of load, is known as (A) Ultimate load carrying capacity (B) Ultimate bearing capacity (C) Ultimate bearing resistant (D) All the above

Description : The maximum load carried by a pile, when it continues to sink without further increase of load, is known as (A) Ultimate load carrying capacity (B) Ultimate bearing capacity (C) Ultimate bearing resistant (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) The bearing capacity of a pile is defined as the load which can be sustained by the pile without producing excessive settlement (B) The safe bearing capacity of a pile is obtained by dividing the ultimate bearing capacity with a suitable factor of safety (C) The factor of safety for piles is taken as 6 (D) All the above

Description : Pick up the correct statement from the following: (A) The bearing capacity of a pile is defined as the load which can be sustained by the pile without producing excessive settlement (B) The safe bearing capacity ... of safety (C) The factor of safety for piles is taken as 6 (D) All the above

Last Answer : Answer: Option D

When an exothermic reversible reaction is conducted adiabatically, the rate of reaction (A) Continuously increases (B) Continuously decreases (C) Passes through a maximum (D) Passes through a minimum

Description : When an exothermic reversible reaction is conducted adiabatically, the rate of reaction (A) Continuously increases (B) Continuously decreases (C) Passes through a maximum (D) Passes through a minimum

Last Answer : (C) Passes through a maximum

The ultimate load capacity of slabs can be determined by using the principle of i.Super position ii.Virtual work iii. Equilibrium [ A ] i [ B ] ii [ C ] i and iii [ D ] ii and iii

Description : The ultimate load capacity of slabs can be determined by using the principle of i.Super position ii.Virtual work iii. Equilibrium [ A ] i [ B ] ii [ C ] i and iii [ D ] ii and iii

Last Answer : [ D ] ii and iii

The bearing capacity of a water logged soil, may be improved by (A) Grouting (B) Chemical action (C) Drainage (D) Compaction

Description : The bearing capacity of a water logged soil, may be improved by (A) Grouting (B) Chemical action (C) Drainage (D) Compaction

Last Answer : Answer: Option C

The bearing capacity of a water logged soil can be improved by (A) Compacting the soil (B) Draining the soil (C) Increasing the depth of foundation (D) Grouting

Description : The bearing capacity of a water logged soil can be improved by (A) Compacting the soil (B) Draining the soil (C) Increasing the depth of foundation (D) Grouting

Last Answer : Option B

For the determination of shear strength parameters, c and , of soil in the laboratory, the test to be conducted will be (a) Triaxial compression test (b) Sieve analysis (c) Compaction test (d) Relative density test

Description : For the determination of shear strength parameters, c and , of soil in the laboratory, the test to be conducted will be (a) Triaxial compression test (b) Sieve analysis (c) Compaction test (d) Relative density test

Last Answer : (a) Triaxial compression test

Which one of the following statements is true? (A) Clays are more porous than sands (B) Pressure of organic matter in a soil decreases the bearing capacity of the soil (C) Aluminous cement is used for foundations in soils with chemical deposits (D) All the above

Description : Which one of the following statements is true? (A) Clays are more porous than sands (B) Pressure of organic matter in a soil decreases the bearing capacity of the soil (C) Aluminous cement is used for foundations in soils with chemical deposits (D) All the above

Last Answer : (D) All the above

The maximum net pressure intensity causing shear failure of soil, is known (A) Safe bearing capacity (B) Net safe bearing capacity (C) Net ultimate bearing capacity (D) Ultimate bearing capacity

Description : The maximum net pressure intensity causing shear failure of soil, is known (A) Safe bearing capacity (B) Net safe bearing capacity (C) Net ultimate bearing capacity (D) Ultimate bearing capacity

Last Answer : (C) Net ultimate bearing capacity

Allowable bearing pressure for a foundation depends upon (A) Allowable settlement only (B) Ultimate bearing capacity of soil only (C) Both allowable settlement and ultimate bearing capacity (D) None of above

Description : Allowable bearing pressure for a foundation depends upon (A) Allowable settlement only (B) Ultimate bearing capacity of soil only (C) Both allowable settlement and ultimate bearing capacity (D) None of above

Last Answer : (C) Both allowable settlement and ultimate bearing capacity

The maximum pressure which a soil can carry without shear failure, is called (A) Safe bearing capacity (B) Net safe bearing capacity (C) Net ultimate bearing capacity (D) Ultimate bearing capacity

Description : The maximum pressure which a soil can carry without shear failure, is called (A) Safe bearing capacity (B) Net safe bearing capacity (C) Net ultimate bearing capacity (D) Ultimate bearing capacity

Last Answer : (A) Safe bearing capacity

The bearing capacity of a soil depends upon (A) Size of the particles (B) Shape of the particles (C) Cohesive properties of particles (D) All the above

Description : The bearing capacity of a soil depends upon (A) Size of the particles (B) Shape of the particles (C) Cohesive properties of particles (D) All the above

Last Answer : Answer: Option D

If the bearing capacity of soil is 10 tonnes/cm2 and the projection of plain concrete footing from walls, is a cm, the depth D of footing is (A) D = 0.0775 a (B) D = 0.775 a (C) D = 0.775 a (D) D = 0.775 a2

Description : If the bearing capacity of soil is 10 tonnes/cm2 and the projection of plain concrete footing from walls, is a cm, the depth D of footing is (A) D = 0.0775 a (B) D = 0.775 a (C) D = 0.775 a (D) D = 0.775 a2

Last Answer : Answer: Option B

Black cotton soil is unsuitable for foundations because its (A) Bearing capacity is low (B) Permeability is uncertain (C) Particles are cohesive (D) Property to undergo a volumetric change due to variation of moisture content

Description : Black cotton soil is unsuitable for foundations because its (A) Bearing capacity is low (B) Permeability is uncertain (C) Particles are cohesive (D) Property to undergo a volumetric change due to variation of moisture content

Last Answer : Answer: Option D

The least bearing capacity of soil is that of (A) Hard rock (B) Moist clay (C) Soft rock (D) Coarse sandy soil

Description : The least bearing capacity of soil is that of (A) Hard rock (B) Moist clay (C) Soft rock (D) Coarse sandy soil

Last Answer : Answer: Option B

Raft foundations are used for: (A) Providing increased area of foundation over poor bearing capacity of soil (B) Spanning over small soft or loose pockets (C) Counter acting the hydrostatic effect (D) All the above

Description : Raft foundations are used for: (A) Providing increased area of foundation over poor bearing capacity of soil (B) Spanning over small soft or loose pockets (C) Counter acting the hydrostatic effect (D) All the above

Last Answer : Answer: Option D

Grillage foundation (A) Is used to transfer heavy structural loads from steel columns to a soil having low bearing capacity (B) Is light and economical (C) Does not require deep cutting as the required base area with required pressure intensity is obtained at a shallow depth (D) All the above

Description : Grillage foundation (A) Is used to transfer heavy structural loads from steel columns to a soil having low bearing capacity (B) Is light and economical (C) Does not require deep cutting as the required base area with required pressure intensity is obtained at a shallow depth (D) All the above

Last Answer : Answer: Option D

In case of foundations on black cotton soils, the most suitable method to increase the bearing capacity of soils is to (A) Increase the depth of foundation (B) Drain the soil (C) Compact the soil (D) Replace the poor soil

Description : In case of foundations on black cotton soils, the most suitable method to increase the bearing capacity of soils is to (A) Increase the depth of foundation (B) Drain the soil (C) Compact the soil (D) Replace the poor soil

Last Answer : Answer: Option D

The maximum bearing capacity of soil is that of (A) Black cotton soil (B) Loose fine sandy soil (C) Dry coarse sandy soil (D) Hard rocks

Description : The maximum bearing capacity of soil is that of (A) Black cotton soil (B) Loose fine sandy soil (C) Dry coarse sandy soil (D) Hard rocks

Last Answer : Answer: Option D

Safe bearing capacity of black cotton soil varies from (A) 2 to 3 t/m2 (B) 5 to 7.5 t/m2 (C) 8 to 10 t/m2 (D) 10 to

Description : Safe bearing capacity of black cotton soil varies from (A) 2 to 3 t/m2 (B) 5 to 7.5 t/m2 (C) 8 to 10 t/m2 (D) 10 to 12 t/m2

Last Answer : Answer: Option B

The slope of 9-line is determined by the (A) Reflux ratio (B) Plate efficiency to be achieved (C) Thermal condition of the feed (D) Relative volatility

Description : The slope of 9-line is determined by the (A) Reflux ratio (B) Plate efficiency to be achieved (C) Thermal condition of the feed (D) Relative volatility

Last Answer : (C) Thermal condition of the feed

Operational audits generally have been conducted by internal and COA auditors, but may be performed by certified public accountants. A primary purpose of an operational audit is to provide: a. A measure of management performance in meeting organizational goalsb. The results of internal examinations of financial and accounting matters to a company's top-level management. c. Aid to the independent-auditor, who is conducting the examination of the financial statements. d. A means of assurance that internal accounting controls are functioning as planned.

Description : Operational audits generally have been conducted by internal and COA auditors, but may be performed by certified public accountants. A primary purpose of an operational audit is to provide: ... statements. d. A means of assurance that internal accounting controls are functioning as planned

Last Answer : A measure of management performance in meeting organizational goals

Which of the following statements is true? a. An independent auditor must be a CPA. b. Compliance audits are conducted to determine adherence to rules and regulations set by the auditor. c. An audit, if properly conducted, ensures that fraud is prevented. d. After conducting an audit and release of the auditor’s report, the primary responsibility on the fairness of the financial statements is shifted to the auditor

Description : Which of the following statements is true? a. An independent auditor must be a CPA. b. Compliance audits are conducted to determine adherence to rules and regulations set by the auditor. c. ... s report, the primary responsibility on the fairness of the financial statements is shifted to the auditor

Last Answer : An independent auditor must be a CPA.

Write the procedure of vaccum dewatering concreting for construction of floors.

Description : Write the procedure of vaccum dewatering concreting for construction of floors.

Last Answer : Procedure of vaccum dewatering concreting for construction of floors: The concreting using vaccum dewatering for floor construction is done as follows. 1. Concrete is places uniformly on the spread of ... Finally the floating and towelling is done to achieve better finishing of surface. 

If we exclude the cost factor, which bearing is preferred? a) Hydrostatic b) Hydrodynamic c) Both are equally preferred d) Cannot be determined

Description : If we exclude the cost factor, which bearing is preferred? a) Hydrostatic b) Hydrodynamic c) Both are equally preferred d) Cannot be determined

Last Answer : a) Hydrostatic